Argos Malibu 426/8154 User manual

MADE IN
BRITAIN
Dimensions
Width - 74.7cm
Depth - 39.6cm
Height - 93.6cm
Malibu - 4 Drawer Media Unit
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 2 - 08/06/15
Important - Please read these instructions fully before starting assembly
ALR3191
426/8154
402/3502
391/8144
425/5198
424/0392
Issue 2 - 08/06/15 - Incorrect prefixes on the Drawer Back and the 2 Backs.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 31kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
12 4
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
5 7
Left Side (DF3308)
(91.1 x 39.4cm)
Shelf (DF3339)
(71.4 x 39.2cm)
Front Rail (DF3304)
(71.4 x 7.2cm)
Back Rail (DF3303)
(71.4 x 6cm) x 2
Drawer Front (DF3338)
(71 x 15.6cm) x 4
Right Side (DF3309)
(91.1 x 39.4cm)
3Top (DF3301)
(74.7 x 39.6cm)
Drawer Back (W682-124)
(68.2 x 12.4cm) x 4
Left Drawer Side (W370-124LH)
(37 x 12.4cm) x 4
Right Drawer Side (W370-124RH)
(37 x 12.4cm) x 4
Drawer Base (T693-367)
(69.3 x 36.7cm) x 4
Small Back (X610-169)
(61 x 16.9cm)
LargeBack (X740-659)
(74 x 65.9cm)
Plinth (DF3302)
(71.4 x 9.2cm)
6
8 9 10
11
12
13
14

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Electric drill
(only use when
drilling into walls)
25mm Screw (F50) x 8
40mm Screw (F910) x 10
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A B
D E F
G H I
L
Small locking
nut (F3) x 8
C
Nail (F51) x 18
M
J
9mm Screw (F74) x 8
K
9mm Screw (F73) x 16
Drawer runner (F1004) x 8
Knock-in Peg (F171GY) x 16
Large locking
nut (F900) x 2
Metal dowel (F901) x 10
Wooden dowel (F22) x 12
N
N
Wedgefix (F639) x 16
Back holder (F276) x 3
*These can also be round
Nail screw (F277) x 3
OStrap Screw Washer x 2
Overbalance protector kit (F269) x 1
P
Handle (F631) x 8

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
x 4
x 4
x 4
x 4
A
A
C
Step 2
Prepare the drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
A
Prepare 4 pairs of the
drawer sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
9
10
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the 4
drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
9
10
8
C
C
9
10
C
CC
910
10
8
9
A
A
8
8
80% x 2

Assembly Instructions
5
Step 4
8
F
F
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
fronts .
Step 5
Fit the drawer back
Fit the drawer back .
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
12
9 10
8
11
9 10
12
11
11
F
Attach the handles
Attach 2 handles to
each drawer front
using 2 screws .
P
H
8
x 4
x 4
x 4
x 4
F
F
10
9
12
12
10
9
9 10
11
N
Fit the wedgefixes
Turn the 4 drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
N
N
NN
N
Step 7
Note: Do not
overtighten the screws.
8P
H
P
H

Finished
front edge
Finished
front edge
Finished
front edge
D
Assembly Instructions
6
Step 8
Finished
front edge
I
M
Prepare the left side
a: Place 4 runners on
the left side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
c: Tap a wooden dowel
. into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert a large locking
nut into the left side
. .
Note: The arrow on the
locking nuts must point
towards the hole in the
edge of the panel.
1
I
I
B
1
1
1
M
M
a:
b:
c:
I
M
I
M
I
M
I
M
I
I
I
I
B
D
10mm
D
1
1
1
B

D
Assembly Instructions
7
Step 9
B
Finished
front edge
I
M
Prepare the right side
a: Place 4 runners on
the right side as
shown. Slide back the
top of runner and use the
2nd hole from the front
to fit the 1st screw .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
c: Tap a wooden dowel
. into the right side .
Insert a large locking
nut into the right side
. .
2
I
I
B
2
2
M
Ma:
b:
c:
I
M
I
M
I
M
I
M
I
I
I
I
Finished
front edge
Finished
front edge
Finished
front edge
2
2
2
2
D

Finished
front edge
Finished
front edge
D
D
Finished
front edge Finished
front edge
G
G
Assembly Instructions
8
Step 10
Fit the shelf to the
right side
Attach the shelf to
the right side using 2
screws .
4
2
G4
2
D
D
Step 11
Prepare the front rail
Tap 4 wooden dowels
into the front rail .
D
5
Step 12
Fit the front rail
Push the front rail
onto the right side .
5
2
5
5
2

D
G
D
Assembly Instructions
9
Step 13
2
D
Prepare the plinth
Tap 2 wooden dowels
into the plinth .
D
6
6
6
Step 14
Fit the plinth
Push the plinth onto
the right side and
secure it with screw .
Step 15
6
2
G
Note: Support the plinth until
the left side has been fitted.
Prepare the 2 back
rails
Tap 2 wooden dowels
into each of the 2 back
rails .
D
7
D
7x 2
6