Argos Aruba 614/3868 User manual

Aruba - Sideboard
614/3868
Assembly Instructions - Please keep for future reference
Important –Please read these instructions fully before starting assembly
Dimensions
Width - 104cm
Depth - 47cm
Height - 83,5cm
Issue 1 - 16/04/13
614/3875
116/6383
If you need help or have damaged or missing parts, call the Argos Customer Helpline: 08456 400 800
or Homebase Customer Helpline: 0845 077 8888

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
We do not
recommend the
use of power
drill/drivers
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
for
inserting screws,
This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
The product has been treated
with a wax and oil finish to
prevent dirt ingress and preserve
moisture.
On unpacking the
furniture you may notice an
odour due to this treatment;
this will disappear once the
furniture is unpacked and
assembled after a period of time.
This process may leave some
staining on the packaging
material; please take care to
ensure this does not transfer
to clothing or carpeted surfaces
during assembly.
Care and maintenance
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

underside
1Top panel (104 x 47cm)
2Base panel (96 x 42.4cm)
3Shelf (96 x 40cm)
4Right side panel (81 x 44cm)
5Left side panel (81 x 44cm)
16 Door x 2
(43.4 x 39.4cm)
17 Drawer front
x 2 (39.5 x 14cm)
18 Drawer sides
x 4 (34 x 14cm)
19 Drawer back
x 2 (37 x 14cm)
top
top
view from behind
Components - Panels
Please check you have all the panels listed below
2
15 Front plinth (103.6 x 9.2cm)
8Top front frame (90.6 x 6.5cm)
9Middle front frame (90.6 x 6.5cm)
10 Bottom front frame (90.6 x 6.5cm)
11 Back column (71.8 x 6.5cm)
12 Vertical frame (48 x 6.5cm)
13 Small vertical frame
(18.8 x 6.5cm) 21 Side drawer runner
x 2 (36.6 x 5.5cm)
14 Side (45 x 9.2cm)plinth x 2
23 Back panel x 2 (75 x 47cm)
20 Middle drawer runner
(40.5 x 8.1cm)
24 Drawer bottom
x 2 (38 x 32.6cm)
6Right front frame (81 x 6.5cm)
7Left front frame (81 x 6.5cm)
22 Block x 4
(10 x 2cm)

3
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(medium & large)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
A
D
G
J
B
E
H
K
C
F
I
L
Wooden dowel x 28 14mm Screw x 37 30mm Screw x 24
50mm Screw x 440mm Screw x 635mm Screw x 21
M
Nail x 32
N
2m
19mm Bolt x 4
O
P
Plug x 2Clip x 2
Door / drawer
handle x 4
Door
hinge x 4
Metal dowel x 6 Locking
nut x 6
Wall strap x 1
Washer x 2
Components - Fittings If you have damaged or missing components,
call the Argos Customer Helpline: 08456 400 800
or Homebase Customer Helpline: 0845 077 8888

Yes!No!
Yes!No!
Step 2
Step 1
Fixing right front frame
to the right side panel
.
(Two people required for
an easier assembly)
Insert right side panel
into right front frame
through joints.
a:
4
Note:
Before fixing the
blocks into
place it is important to
ensure that the slot and
groove of parts and
are fully pushed together
and lined up correctly at
the top and bottom.
D
c:
.
Fix front frame through
blocks using screws
4
b: Place blocks in the
to the side panel using
screws .
positions shown. First fix
6
6
D
Assembly Instructions
4
22
22
22
Fixing left front frame
to the left side panel
.
(Two people required for
an easier assembly)
Insert left side panel
into left front frame
through joints.
a:
5
Note:
Before fixing the
blocks into
place it is important to
ensure that the slot and
groove of parts and
are fully pushed together
and lined up correctly at
the top and bottom.
D
c:
.
Fix front frame through
blocks using screws
b: Place blocks in the
to the side panel using
screws .
positions shown. First fix
7
D
22
22
7
5
a: b: c:
Top
a: b: c:
4
160mm
100mm
110mm
330mm
100mm
Top
160mm
100mm
110mm
330mm
100mm
5
7
D
D
D
4
6
D
7
5
6
22
22
22
22
22
22
22
43mm
6
Attention!
43mm
Attention!
7

Assembly Instructions
5
Step 3
Step 4
Insert dowels into the
indicated parts.
1
Fitting Metal dowels.
Do not over tighten.
Screw metal dowels
into top panel .
Insert metal
dowels as far as
shown.
Note:
H
H
H
H
A
4
A
2x
11
20
21
A
A
2
A
A
3
A
AA
1
Step 5
Insert 2 dowels in the
right side panel .
Fit side drawer runner
to the right side panel
then fix it using screws
as shown.
Repeat step 5 for the
other side drawer runner
and left side panel .
A
A
21
21
F
F
21
4
4
5

Assembly Instructions
6
Step 6
Step 8
Assembling parts.
Put parts , , ,
and together as
shown in the diagram.
Attention!
To the correct
holes position.
Insert the assembled
frame into the holes on
left side panel .
8 9 10 12
13
5
Step 7
8
9
10
12
13
5
Fixing panels.
Attach base panel to
the left side panel
using screw .
Fit shelf to the left
side panel .
H
Attention!
You might need to rotate
base panel to get it in the
right position.
oles on base
panel to be facing up.
2
E
5
3
5
5
E
E
23
2
Attention!
10
8
Attention!

Assembly Instructions
7
Step 9
Step 10
4
Place side properly
ensuring dowels and front
frames , and are
all fit into their holes at
the same time.
Fix right side panel to
the base panel using
screws . 2
E
8 9 10
4
E
4
E
Fixing middle drawer
runner.
Important:
With help,
carefully stand the
product upright.
Fit middle drawer runner
to the small vertical
frame then fix using
screw .
Make sure middle
drawer runner is
positioned as shown in
the diagram prior to fixing.
Attention:
13
D
Attention:
D
2
20
20

Assembly Instructions
8
Step 11
Step 12
Fixing back column.
Fit back column to
the base panel and
middle drawer runner
then fix it using screw .
20
11
D
2
2
20
11
D11
1
2
11
D
Fixing top panel.
With help, f
Insert locking nuts
into anel where
shown
Use a screwdriver to turn
locking nuts clockwise
to lock
to base panel and
top panel using screws
.
to top panel using
screw .
6
side p s
.
.
Do not over tighten.
it top panel
to the cabinet.
Attach back column
Attach top front frame
I
I
1
I
I
11
2
1
D
1
8
D
D
20
I
I
D

Assembly Instructions
9
Step 14
Step 13
With help, carefully
lay down the product.
Fix bottom front frame
to the base panel
using screw .
a:
Important:
b:
c:
b:
C
14
14
Fitting hinges to doors.
a: Attach hinges to the
pre drilled holes in the
door using screws .
B
10
15
C
a:
10
C
2
b: Fix side plinths to
the side panels using
screws .
Make sure
side plinths are
aligned to the bottom and
front edges of the side
panels.
Note:
c: Fix front plinth
to the bottom front frame
using screws .
Make sure front
plinth is aligned to the
bottom edge of the side
panels and in line to the
side plinths.
Note:
14
C
15
10 C
15
J
J
16
B
B
B
G
K
b:
a:
b: Attach handle to the
door using bolt , then
fix handle plate to the
door using screws .
Make sure handle plate
is aligned before fixing.
Repeat step 14 for the
other door.
K
G
B
10
C