Argos Nest of Tables 609/1439 User manual

Chloe Nest of Tables
Assembly Instructions -
Please keep for future reference 609/1439
Dimensions
Depth - 40/30cm
Width - 56/40cm
Height - 47/35.5cm
Large / Small
609/1893
609/6300
Important - Please read these instructions fully before starting assembly
Version 3 Date: 19/03/15
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
415/9672

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
Handy Hints

2
Large table top (56 x 40cm)
1
Small table top (40 x 30cm)
2
Large support x 2 (43.8 x 6cm)
3
Medium support x 4 (27.8 x 6cm)
4
Small support x 2 (17.8 x 6cm)
5
Large leg x 4 (45.5 x 4.5cm)
6
Small leg x 4 (34 x 4.5cm)
7
Pilot holes for
guidance only
Pilot holes for guidance only
Pilot holes for
guidance only
Pilot holes for
guidance only
Pilot holes for
guidance only
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800

3
Note: The quantities below are the correct amount to complete the assembly. in some cases mor
may be supplied than are required.
40mm Dowel x 24
Components - Fittings
43mm Locking pin x 16 14mm Screw x 20
ABC
15mm Locking nut x 16
DE
Plastic support x 10
Ruler - Use this ruler to help correctly identify the screws
Tools required
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
7mm Suitable drill bit
(for use with wall plug)
The screws length is measured from the head to the point (30mm screw shown).

4
a:
b:
Assembly Instructions
Step 1
Fitting the large legs
b:
onto the Large support
Locking nuts
Large legs
.
D
6
3
Note:
assembly the other legs.
Follow the same
Note: It would be useful
to ask
someone to help
you at this stage.
a:
Insert Dowels into
the Large legs .
B
Note: The screw holes
on the legs and support
should align.
Use a screwdriver to turn
Locking nuts clockwise
to lock.
D
b to
Continued on next page.
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
Screw Locking pins into
the Large legs .
A
6
6
X 4
B
B
B
A
A
6
X 2 D
D
3
6
6
D

5
Assembly Instructions
Step 1 - continued
c:
the Medium supports .
Large legs
Locking nuts
6
D
4
Note: The screw holes
on the medium supports
should face inward.
Use a screwdriver to turn
Locking nuts clockwise
to lock.
D
Continued on next page.
Step 2
6
6
6
6
A
A
A
A
Fitting the large table
top
a:
Insert Dowels fully
into the Large legs
.
6
A
c:
a:
D
6
6
6
6
3
3
4
4
D
D
D
D

Step 2 - continued
b:
c:
Plastic supports onto
the Large table top .
E
1
C
1
C
C
E
Carefully locate the
Large table top onto
the unit.
1
c:
b:
6
Assembly Instructions
C
C
E
1

Assembly Instructions
Step 3
Step 4
7
Finishing the large
table
Carefully turn the table
upright.
X 4
B
7
B
B
A
A
Fitting the small legs
a:
Insert Dowels into
the Small legs .
B
Note:
Insert Locking pins
as far as shown.
Do not over tighten.
Screw Locking pins into
the Small legs .
A
7
7
Continued on next page.
a:

Assembly Instructions
Step
8
7
5
7
b:
onto the Small support
Locking nuts
Small legs
.
D
7
5
Note:
assembly the other legs.
Follow the same
Note: It would be useful
to ask
someone to help
you at this stage.
Note: The screw holes
on the legs and support
should align.
Use a screwdriver to turn
Locking nuts clockwise
to lock.
D
b to
c:
the Medium supports .
Small legs
Locking nuts
7
D
4
Note: The screw holes
on the medium supports
should face inward.
Use a screwdriver to turn
Locking nuts clockwise
to lock.
D
D
D
4
4
5
5
7
7
7
7
D
D
b:
c:
X 2
D
D
4 - continued

9
Assembly Instructions
Step
A
A
A
A
a:
b:
5
Step
Fitting the small table
top
a:
Insert Dowels fully
into the Small legs
.
7
A
Carefully locate the
Small table top onto
the unit.
2
b:
2
7
7
7
Continued on next page.