Argos Aubrey 549/6516 User manual

Length - 200,5cm
Width - 152,1cm
Height - 110cm
Aubrey - 4ft6 Bed
Assembly Instructions- Please keep for future reference
Important – Please read these instructions fully before starting assembly
Issue 06 - 04/04/17
Dimensions
If you need help or have damaged or missing parts, ca l l t h e customer Helpline: 03456 400 800
549/6516
549/9441
709/6055

Note: if required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
. Check you
have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
.
plastic bags and separate them
into their groups.
Keep children and animals
.
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
.
space to layout the parts before
starting.
Do not stand or put weight on
.
the product, this could cause
damage.
We do not
.
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
.
easier with 2 people.
Dispose of all packaging
.
carefully and responsibly.
care and maintenance
. Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
.Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
.
From time to time check
that there are no loose
screws on this unit.
.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
Assemble on a soft level
.
surface to avoid damaging the
unit or your floor.
Assemble the item as close
.
to its final position (in the same
room) as possible.
. This product contain natural
timber. You may notice some
variation in the grain and
colour of different component
parts which is normal for
furniture produced using
natural wood and is not the
result of any manufacturing
fault.

01 Headboard (152,1 x 110,0cm)
02 Footboard (152,1 x 60,0cm)
03 Side rails x 2 (190 x 11,5cm)
04 Central Support (191 x 6cm)
05 Support Foot x 2 (27,8
x 6cm)
06 Slats x
26 (68 x 6,9cm)
Components - Panels
Please check you have all the panels listed below
2

Components- Fittings
Please check you have all the fittings listed below
If you have damaged or missing components,
call theCustomer Helpline: 03456 400 800
Note:The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
D
40mm Wooden dowel x 04
A
90mm Bolt 1/4 x 04
B
Half-Moon Nut 1/4 x 04
E
35mm Screw x 52
H
Nut 1/4 x 06 70mm Headless Bolt 1/4 x 04
I
C
Allen key x 01
G
Spanner x 01
F
Washer 1/4 x 04
J
16mm Screw x 08
L
80mm L Shaped Bracket x 02
M
40mm Bolt 1/4 x 02
O
50mm Bolt x 04
N
Spacer 83mm x 02
2m
Ruler- Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(medium & large)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
3

Step1
4
Fitting dowels
Insert dowels
into the indicated parts.
D
Assembly Instructions
D
D
D
D
D
03
03
Step 2
03
03
G
G
I
I
F
F
H
H
02
02
A:
B:
Assembling side rails
Screw headless boltA:
to footboard as shown.
Fix headless bolts using
nuts and spanner .
02
I
H
G
Do not over tighten.
I
B: Insert washer to
side rails and fit
footboard to side rails.
F
03
the

Step 3
Assembly Instructions
A
C
B
B
B
C
01
03
03
A
B
5
Step 4
Fixing support foot
C
O
04
05
C
05
B
C
A
03
Attach side rails to
the headboard. Insert
half moon nut into
side rails as shown.
Then fix them to the
headboard using
bolts and allen key .
03
01
Fix Support foot to
Central support
using Bolt and Allen
Key as shown.
05
04
O
02

Assembly Instructions
Step 5
Step 6
6
Fixing L shaped brack
Fix L shaped brackets
into pre-drilled holes in the
headboard and
footboard using screws
as shown. Do not over
J
L
01
01
Fixing central supp
Fix central support
to L shaped brackets in
headboard and
footboard using bolts
and nut as shown.
H
M
04
01
02
02
02
M
H
L
J
J
J
J
04
02
tighten screws.
L

7
Assembly Instructions
Additional step to fixing
slats Warning!
collide.
Assemble is complete!
Step 7
E
Step 8
N
N
Fixing slats
06
Make sure that
s slats screws
never collide to the
screws on the slats
support bar, as shown
in the diagram.
E
N
Using spacer ,
centralize slats in bed
frame prior to fixing. Fix
slats using screws , as
shown.
Fix slats in one side first,
then fix them in the other
side by pushing the rail
against the slats if
necessary.
Periodically check that
all screws are tight.
EN
N
E
E
N
N