Argos Tolga 03R 462/6071 User manual

Dimensions
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline:
Assembly Instructions - Please keep for future reference
Tip : To prevent damage,
we recommend that you
build your unit on the
carton(s) it was packed in.
Height - 180cm
Depth - 51,75cm
Width - 112,5cm
Tolga 03R
Argos = 03456 400 800
462/6071
482/6369
496/5581
496/5581 BLUE
482/6369 PINK
462/6071 OAK
Issue: 3 - 18/05/16
DR825205

1
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
•
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fi ttings are
tightend properly.
Handy Hints
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below•
Important – Please read these instructions fully before starting assembly
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• Check you have all the
components and tools listed
on the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Assembly should be carried out
by a competent adult only.
• do not use this item if any
components are missing
or damaged.
• this item is suitable for childeren
from the age of 6.
Safety and Care Advice

Please check you have all the panels listed below
Components - Panels If you have damaged or missing components,
call the Customer Helpline:
2
03456 400 800
Back Broad x1
(1723 x 741 x 2,5mm)
1
BO2579
Back Narrow x1
(1723 x 376 x 2,5mm)
2
BO2581
Top x1
(1095 x 496 x 18mm)
3
P1012
Shelf Broad x1
(720 x 494 x 18mm)
4
P1013
Shelf Narrow x1
(357 x 494 x 18mm)
5
P1014
Bottom x1
(1095 x 496 x 18mm)
6
P1015
Right Side x1
(1800 x 497 x 15mm)
7
P2128
Mid panel x1
(1693 x 495 x 18mm)
8
P2129
Left Side x1
(1800 x 497 x 15mm)
9
P2131
Door left/right x2
(1743 x 372 x 18mm)
10
P3136
Plinth x1
(1095 x 70 x 15mm)
12
P7156
Door Middle x1
(1743 x 372 x 18mm)
11
P3137

Please check you have all the fittings listed below
Components - Fittings
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Tools required
Eye protection
(when using a
hammer or glue)
Ruler/tape
measure
0102030405060708090 100 110 120 130 140 150
0123456
Small
hammer
Setsquare
Spirit level
Drill
6mm Suitable drill bit
(for use with wall plug)
Flatblade screwdriver
(medium)
Phillips screwdriver
(medium & large)
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
The screws length ismeasured from thehead to the point (30mm screw shown).
3
Hanger rail x 1 (712mm)
PM1829
V
Hanger rail x 1 (350mm)
PM1804
U
Parkerscrew x 1 (dimension)
ZF99936B
T
Wall Plug x 1 (6mm)
ZF99936A
S
Hinge x 9
FK1263
R
Hinge back x 9
FK1262
Q
Nail Holder x 1
FK1415
P
Wood Dowel x 4 (5x30mm)
FK1410
O
Screw x 24 (4x15mm)
FK1400
N
Screw x 4 (3x15mm)
FK1311
M
Pozi Screw x 18 (4x12,5mm)
FK1309
L
Corner connectro, white x 2
FK1248
K
L-bracket x 1
FK1235
J
Peg, Brown x 1
FK1234
I
Hanger Rail support x 4
FK1223
H
Double locking bolt x 3 (7x62,5mm)
FK1018
G
Allen Key x 1 (3mm)
FK1013
F
Locking Nut x 24 (15x12mm)
FK1012
E
Locking screw x 18 (5x24mm)
FK1011
D
Confirmat screw x 4 (5x40mm)
FK1005
C
Nail x 60
FA1515
B
Glue x 1
FA1510
A
15mm

Assembly Instructions
4
6
3E
E
EE
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
4
5
H
H
M
M
Q
Q
Q
Q
D
D
D
D
D
D
D
D
D
D
9
Finished
front edge
Step - 1
Step - 2
Insert locking nuts E
into shelfs 3.
Make sure the ‘arrow’ on
locking nuts Epoints
towards the hole in the
edge of 3.
Repeat with panels:
4, 5, 6.
Screw locking screw D
into left side 9.
Note: Insert locking
screw Das far as shown.
Do not over tighten.
Attach hanger rail support
Husing 15mm screw M
onto left side 9.
Screw hinge back Qonto
left side 9.

H
H
M
M
D
D
D
D
D
D
D
D
D
D
7
Q
Q
Q
Q
H
H
M
M
8
Q
Q
QQ
H
H
M
M
8
Finished
front edge
Assembly Instructions
5
180˚
Finished
front edge
Finished
front edge
Step - 3
Step - 4
Screw locking screw D
into right side 7.
Note: Insert locking
screw Das far as shown.
Do not over tighten.
Attach hanger rail support
Husing 15mm screw
Monto right side 7.
Note: Use the lower two
holes to mount hanger
rail support Honto right
side 7.
Screw hinge back Qonto
right side 7.
a: Attach hanger rail
support Husing 15mm
screw Monto mid panel
8.
Note: Use the lower two
holes to mount hanger
rail support Honto mid
panel 8.
Turn panel over
b: Attach hanger rail
support Husing 15mm
screw Monto mid panel
8.
Note: Use the upper two
holes to mount hanger
rail support Honto mid
panel 8.
Screw hinge back Qonto
mid panel 8.
a:
b:

12
O
O
A
O
O
O
3
8
C
C
C
C
6
F
5
G
G
G
G
3
84
6
Assembly Instructions
6
Finished
front edge
Finished
front edge
Finished
front edge
Position Top panel 3
onto mid panel 8.
Insert two confirmat screws
Cthrough top panel 3
into mid panel 8as
shown.
Use allen key Fto turn
confirmat screw Cinto
panel.
Repeat with bottom 6.
Attaching panels
Step - 4
Step - 5
Step - 6
Put drop of glue Ainto the
4 holes of plinth #.
Put dowels Ointo the
holes of plinth #.
Insert three double locking
bolts Ginto mid panel 8
as shown.
Position shelf broad 4
onto mid panel 8.
Use a screwdriver to turn
locking nuts Eclockwise
to lock.
Repeat with shelf narrow
5.
Attaching panels

7
53
4
8
6
5
3
7
4
8
12
6
9
Assembly Instructions
7
Finished
front edge
Finished
front edge
Step - 7
Step - 8
Attaching panels
Position right side 2onto
the unit.
Use a screwdriver to turn
locking nuts Eclockwise
to lock.
Attaching panels
Position Plinth @onto
the unit as shown.
Position left side 9onto
the unit.
Use a screwdriver to turn
locking nuts Eclockwise
to lock.

11
L L
L
L
L
L
LL
L
LLL
L
L
10
R
R
R
R
R
R
R
B
B
P
B
B
B
P
1
12
6
2
N
N
N
N
N
N
NNNNNN
NN
N
N
N
N
N
N
N
N
N
N
N
K
K
K
9
Assembly Instructions
8
Step - 9
Step - 10
Fitting hinges to doors
Fix hinge door Rto doors
!,0(2x) using 12,5mm
Pozi screw Linto the holes
of doors !,0(2x).
Fitting back panel
Attach back 1,2to the
back with the coloured
surface facing the inside
using nails B.
Use nail holder Pto
hold the nails Bvertical
and at correct distance as
you secure the back 1,2.
Nails Bshould be spaced
about 150mm apart.
Use screw Ninto the holes
of back 1,2to attach to
the shelf 6.
Use screw Ninbetween
panel 1and 2to fix them
to mid panel 8.
Important:
Furniture MUST
be ‘square’ when
back is attached.

R
Q
6
12
8
1
5
H
U
U
V
9
4
3
V
6
12
8
1110 10
9
4
3
/
Assembly Instructions
9
Step - 11
Step - 12
Inserting hanger rail
Insert hanger rail large V
into hanger rail support H.
Insert hanger rail U
into hanger rail support H
Hanging doors
With help, slot hinge door
Ronto hinge back Q.
Tighten screw shown to
lock hinges in position.
Note: Look first to
‘assemble’ on page ‘hinge
instructions’
For adjusting the doors 0,
!see ‘adjustment’ on
page ‘hinge instructions’