Argos 1866968 User manual

Ref. no NOR 10.00 Date: 6/06/11
Desk
A embly In truction - Please keep for future reference
Important - Please read these instructions fully before starting assembly
Dimen ion
For enquirie relating to pare part plea e contact : 08456 400800
Width - 110.1 cm
Depth - 44.3 cm
Height - 81 cm
1866968
186698

Safety and care advice
Important - Please read these intructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 3 and 4.
Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight
on the panels, this could cause
damage.
• Assemble the unit as close
to its final position (in the same
room) as possible. •
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• If using power tools, please
follow the safety instructions
supplied with the tools.
•We do not
recommend the
use of power drill/
drivers for inserting
screws, as this
could damage the unit. Only use
hand screwdrivers.
• Warning: Before drilling,
check the wall for hidden pipes
and cables.
• Dispose of all packaging
carefully and responsibly.
• Warning: The unit weighs
approximately 34kgs
Please lift with care.
Recycling – the packaging materials for this product may
be recycled through your local recycling centre. When you
want to dispose of the product itself, please consider
donating it to a local charitable organisation, otherwise
recycle it through your local recycling centre.
Cleaning instructions
• This product has been
manufactured using modern
manufacturing methods and
materials. With appropriate
in-home care and mainte-
nance it will provide trouble
free performances. Many
domestic multi-purpose
cleaning agents are unsuitable
for use on this product.
The use of aggressive chemi-
cals can result in irreversible
damage. Please follow these
guidelines carefully.
USE only 5% soap, 95%
water solution, wiping with a
damp (not wet) cloth. Finally
dry with a soft clean cloth.
Dust with a soft clean cloth
only.
DO NOT USE wax furniture
polish, abrasive or aggressive
cleaners, bleach or hypochlo-
rate (chlorine) based cleaners,
multi-purpose cleaners,
dilutes, acetone, alcohol,
solvent or similar products.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
2

1
5
10
4
14
9
8
RAW
Left side x 1
(41.8 x 78.8cm)
2
Right internal side x 1
(41.8 x 78.8cm)
3
Right external side x 1
(41.8 x 78.8cm)
Top x 1 (110.1 x 44.3cm)
Back panel drawer x 1
(43.9 x 73.6cm)
6
Back panel desk x 1
(63.4 x 37.1cm)
7
Back structural plinth x 1
(41.8 x 7.8cm)
Front structural plinth x 3
(41.8 x 5cm)
Front structural plinth x 1
(41.8 x 7.8cm)
F
Left drawer
side x 3 (40 x 14cm)
12
Front drawer x 3
(44.7 x 21cm)
11
Right drawer
side x 3 (40 x 14cm)
R
Drawer bottom x 3
(38 x 39.8cm)
13
Back drawer x 3
(36.85 x 14cm)
S
3
Component - Panels
Plea e check you have all the panel li ted below

Wooden dowel x 32 Support foot x 6
Ruler -Usethisruler to help correctly identify thescrews
Tools required
A
Metal dowel x 32
Spacer x 1
Note: The quantities below are thecorrect amount to complete the assembly. In some cases more
fittings may be supplied than are required.
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
ET
Z
C D
I
12mm Screw x 18 25mm Nail x 30
Long locking
nut x 20
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
01234 56
Phillips screwdriver
(medium & large)
Spirit level
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer)
mm
P
X
B30mm
Bumper x 3
U
V
Strap x 1 30mm Screw x 12
15mm Screw x 1
11mm Euroscrew x 12
Short locking
nut x 12
Pair of roller runners x 3
Z2
Z1
B1
Component - Fittings For enquirie relating to pare part plea e
contact : 08456 400800
Plea e check you have all the fitting li ted below
4

Fit wooden dowels A
Fit metal dowels B
Fit long locking nuts D
Fix runner parts Z to
the side panel through
holes shown in the detail
view using euroscrews
and screws .
Fit support foot .
Fit wooden dowels A
Fit metal dowels B
Fit long locking nuts D
Fit support foot .
Preparation of side
panels
Preparation of right
external panel and
structural plinths
C
C
C
B
T
D
D
D
D
D
A
C
B
A
Z1
U
Assembly Instructions
Step 1
Bottom
Bottom
Bottom
2
Front
Front
1
3
B
B
B
C
B
B
B
B
B
RAW
Z1
Z1
A
A
A
Front
Front
Z1
U U
T
U
C
C
C
9
8
7
x3
5

Fit metal dowels a onto
top .
Fit long locking nuts b
and wooden dowels A
onto back panel .
Preparation of top and
back panel desk
B
Assembly Instructions
Step 2
Step 3
6
6
4
4
2
1
7
A
A
A
A
A
B
B
C
C
8
9
9
9
RAW
B
Attaching panels
2
Fit metal dowels a onto
right internal side .
Position structural plinth
7 onto the
side .
Use a screwdriver to turn
locking nuts D clock-
wise to lock.
B
Important:
Two people are
needed here
A
7 8 9
12
6

Attaching panels
Position top panel 4
onto the side panels
1 2
Use a screwdriver to turn
locking nuts D clock-
wise to lock.
Fix of top panel
Assembly Instructions
Step 4
Step 5
B
B
Position back panel desk
6 onto the side .
Use a screwdriver to turn
locking nuts D clock-
wise to lock. B
Important:
Two people are
needed here
1 2
4
B
4
1
2
6
6
3
3
3
3
2
2
7

Assembly Instructions
Step 6
Step 7
5
5
E
Position back panel
5
Attach back panel
using 30 nails G
Attach back panels
E
5
Important:
Cabinet MUST
be “square”
when the back
is attached
8

Assembly Instructions
Step 8
Step 12
Important:
two people are
needed here.
To prevent possible
overbalancing we
recommend that this unit
is secured to a suitable
wall.
Secure one end of the
wall strap to the wall.
Thread the other end of
the wall strap h through
the gap between the top
of the chest and the
back panels.
Working from the front of
the chest, fix the wall
strap to the underside of
the top using the wall
strap screw h and
spacer i supplied.
Thread the screw
through the spacer and
then through the end of
the wall strap and into
the pilot hole in the
underside of the top.
Do not fix the wall strap
to any other component.
Top of Unit
W
A
L
L
W
A
L
L
W
A
L
L
Important:
Take care when drilling
the wall that you do
not drill into any pipes,
wires etc. If in doubt,
consult an expert.
wall plug and screw
not included.
Wall fixing
V
V
V
V
V
I
I
X
X
X
9

Fit runner
Fix runner part 2 onto the
drawers using 12 mm
screws .
Repeat this step for all
drawers.
Assembly Instructions
Step 9
Step 10
12
12
T
Assembling of drawer
box
Fit the RH 14 and LH
13 drawer sides to the
drawer backs 15 using
30 mm screws S
Assembling drawer
fronts
Slide drawer bottom
panels 11 into the drawer
boxes grooves.
Fit short locking nuts E
to the drawer side panels
14 13 .
Insert wooden dowels A
in the drawer side panels
14 13 .
Fit metal dowels B onto
the drawer fronts .
Fix bumper as shown.
Position drawer fronts
2 onto drawer boxes
turn locking nuts E
clockwise to lock.
Repeat this step for all
drawers.
11
10
11
10
14
A
12
12
ZZ
11
13
10
11
11
14
10
10
13
13
Z2
C
B1
C
B1
B1
Z2
A
Z2
T
T
P
P
P
10