Argos Baby Amelie 228/2785 User manual

If you need help or have damaged or missing parts, call the
Important - Please read these instructions fully before starting assembly
Dimensions
Width - 80 cm
Depth - 40 cm
Height - 80 cm
Baby Amelie-
Assembly Instructions 228/2785 - Please keep for future reference
Customer Helpline: 08456 400 800
3 Drawer Chest
Issue 1 - 24/04/14

Note:if required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
.Check you have all the
components and tools listed on
pages 2 and 3.
.Remove all fittings from the
plastic bags and separate them
into their groups.
.Keep children and animals
away from the work area, small
parts could choke if swallowed.
.Make sure you have enough
space to layout the parts before
starting.
.Do not stand or put weight on
the product, this could cause
damage.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
.
.Assemble the item as close
to its final position (in the same
room) as possible.
.Assemble on a soft level
surface to avoid damaging the
unit or your floor.
Care and maintenance
Avoid placing the furniture in
Use an appropriate furniture .From time to time check
that there are no loose
screws on this unit.
.This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.
.
.
direct sunlight as this will cause
the timber to prematurely age.
polish for natural wood
furniture and a dry cloth to
clean the product.
Safety and Care Advice
Important -
.
.
Please read these instructions fully before starting assembly

2
Components - Panels
Please check you have all the panels listed below
15 Back panel x 2 (57.7x35.8 cm)
3
16 H profile x 1 (55x1.7 cm)

3
Components - Fittings If you have damaged or missing components,
call the Customer Helpline: 08456 400 800
Note:The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Phillips screwdriver
(medium & large)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
Tools required
Wooden dowel x 24 30 mm Screw x 24 12 mm Screw x 19
12 mm Screw x 12 Right runner x 6
Nail x 18
Knob x 6 20 mm Bolt x 6
Please check you have all the fittings listed below
A B C
FED
G H I
K
J
Left runner x 6
Locking nut x 8Metal dowel x 8
30 mm Screw x 12
L
Wall strap x 1 Washer x 1
NM
E2
E1 F1
F2

4
Assembly Instructions
A
Step 1
Fitting Wooden Dowels:
Insert dowels into holes in
the indicated parts.
G
Fitting metal dowel
Screw metal dowel into top
panel , side panels and
.
Step 2
L
Parts , , , , and
are labelled for easier
identification.
Attach left side panel to left
front foot and left back foot
using screws .
Attach right side panel to
right front foot and right
back foot using screws .
2
3
L
Note: Insert metal
dowels as far as
shown.
Do not over tighten. 3
3
4
6
8
9
Attention:
Make sure side
panels are correctly
aligned and in flush
with the top of the
feet prior to fixing,
as shown.
2345 6
7

5
Assembly Instructions
Step 3
C
E
Fixing runners:
Fix runners and in the pre
drilled holes on side panel
and using screws .
Step 4
2
3
F
Assembly the cabinet
Fit bottom frame and back
rail to the right side panel
as shown.
Insert 2 locking nuts into
bottom frame and back rail
where shown.
Use a screwdriver to turn
locking nuts clockwise to
lock.
Do not over tighten.
H
8
9
3
8
3
8
9
H
Attention:
Make sure runners
are positioned as
shown.

Assembly Instructions
Step 5
Step 6
6
Fit left side panel to bottom
frame and back rail as
shown.
Insert 2 locking nuts into
bottom frame and back rail
where shown.
Use a screwdriver to turn
locking nuts clockwise to
lock.
Do not over tighten.
H
Fit top panel to left side
panel and right side panel
then, insert 4 locking nuts
into side panels where
shown.
Use a screwdriver to turn
locking nuts clockwise to
lock.
Do not over tighten.
H
2
3
8
9
1

Assembly Instructions
Step 7
7
Drawer assembly
B
A) Attach drawer sides and
in the drawer front using
screws .
B) Slide drawer bottom in to
slots on drawer sides and .
C) Attach drawer back to
drawer sides and using
screws .
D) Fix knob using bolts .
E) Fix runner and using
screws as shown.
12 10
12
JK
B
12 10
12
12
Make sure finished
side face inside the
drawer.
EF
D
BB
BB
Finished side
to face inside
A)
B)
C) D)
E)
Make sure runners
are positioned as
shown.

Assembly Instructions
Step 8
Step 9
I
Carefully turn the chest upright.
Fix back panels within
rebates using nails . Ensure
H profile is in place before
nailing as shown.
Important: Cabinet
MUST be 'square' when
back is attached.
1515
Insert drawers
Hook the wheels of the runner
on the back of the drawers over
the wheels of the runners on
the left and right sides, then
hold the drawers level and slide
backwards into position.
8
15
15
16
Fixing back panels

Assembly Instructions
Step 10
Step 11
Adjusting drawers
Loosen the screws in the
runners, adjust the drawers to
suit and once drawers are
aligned retighten and insert 1
screw into fifth hole of the
runners and .
C
F
E
9
+/-
Adjusting drawers
To move drawers left or right:
loosen the screws in the
runners, adjust the drawers to
suit and once drawers are
aligned retighten.
1