Argos Jenson 937/4610 User manual

Spare Parts
Visit: www.argos-support.co.uk
Email: [email protected]
Call: 0330 016 1114
Customer Support
Call: 0345 640 2020
JENSON
Gloss
937/4610 940/4597
Issue 2 - 29/09/20

Safety
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 66kgs.
Please lift with care.
• During assembly children
should be kept away from the
product due to possible risk of
injury.
• Installation shall only be
carried out exactly according to
the manufacturer’s instructions -
otherwise a safety risk can
occur if incorrectly installed.
• Do not use this item if any
components are missing or
damaged.
Care Advice
• Check you have all the
components and tools listed on
relevant pages.
• Remove all fittings from the
specified plastic bag and
separate them into their groups.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• WARNING: To prevent
possible overbalancing this unit
must be secured to a wall using
the 2 overbalance protector kits
supplied.
• A unit that is allowed to topple
can cause serious or fatal injury.
In addition to wall fixing the unit,
place heavy items on the lower
shelves, do not put any heavy
objects on top of the unit and
never allow children to climb or
hang on drawers, doors or
shelves.
• Refer to guide after section 27
for wall fixing information.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• Assembly videos are
available throughout
these instructions by
scanning in the QR
codes.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean with a damp cloth.

Cabinet Panels Please do NOT remove any protective film until after assembly
173.3 x 42.9cm
DF-00023252 DF-00023253
DF-00023248
DF-00013263
DF-00023249
DF-00021905 XDF-00022863
DF-00023255
273.3 x 42.9cm 376.4 x 41.4cm
679.8 x 45cm
8 63.7 x 39.3cm
476.4 x 6cm x 2
567.7 x 77.4cm
776.4 x 41.3cm

Fittings Use these drawings to
correctly identify the fittings
Main Bag
F900
A
F22 F901
Ax 16 Bx 12 Cx 12 D
F
F639
x 7
F110
x 4
GI
F137
x 4
F646
x 4 E
F51
x 5
F63
Hx 8
F474
Jx 2 Kx 4
F328
Tools
Only used for
drilling walls

1
2
1
2
1
2
1
Ax 6
2
Bx 4
3
Cx 8
Finished
front edges

4
5
3
Bx 4 Ax 6
1
3
Finished
front edge
Finished
front edges
x 2

6
Bx 4
Ax 4
7
4
2
4
8
4
4
1
Finished
front edge
x 2
x 4

9
10
5
x 4
D

11
12
5
www.youtube.com/watch?v=FeaI6541z7o
Squaring up a Chest and fitting the Back Panel
A = B
Make sure measurement
A and B are the same
The Back panel must be
flush with the Back Rail.
A
B
x 5
E

13
Cx 4 Jx 2
6
6
14
IMPORTANT:
The Back panel must
slot into the groove
in the Top panel
Finished
front edge
Finished
front edge
Only use 1 Screw
to fit each Bracket
x 4

15 Fx 7

16
Top
WARNING!
In order to prevent overturning
this product must be used with the 2
wall attachment devices provided
Slide the Brackets against the wall. Fit the 2nd screws supplied
with the Brackets into the underside of the Top panel.
Mark the slot at the back of the Brackets for drilling into the wall.
Wall fixings are not supplied as they will need to suit the wall type.
Note: Take care when drilling the wall that you do not drill
into any pipes, wires etc.
If in doubt, consult an expert.
See the next section for a guide
to wall mounting and fixings

Important note:
Important: When drilling into walls always
check that there are no hidden wires or pipes etc.
If plastic wall plugs
are supplied with your
product:
- these are only suitable for
use in masonry walls.
If you are in any doubt about
the correct wall plugs for
your wall, seek professional
advice.
Failure of the product due to
using incorrect fixings is the
responsibility of the installer.
Make sure that the screws and wall plugs being used
are suitable for supporting your unit. Consult a qualified
tradesperson if you are unsure.
Hints:
1: General rule: Always use a larger screw and wall plug
if you are not sure.
2: Ensure you use the recommended drill bit to match the wall
plug and hole size.
3: Ensure you drill the hole horizontally, do not force the drill or
enlarge the hole.
4: Take extra care when drilling high walls, ceilings and ceramic
tiles. Ensure wall plugs are inserted beyond the thickness of
the ceramic tiles to avoid the tiles splitting or cracking.
5: Ensure wall plugs are well fitted and are a tight fit in the
drilled hole.
Types of walls You can use one of the following types of wall plug if your
walls are made of brick, breeze block, concrete, stone or wood.
Generally aerated blocks should not
be used to support heavy loads, use
a specialist fitting in this case. For light
loads, general purpose wall plugs can
be used.
For use with plasterboard partitions or
hollow wooden doors.
For use with walls stuck with
plasterboard. The hammer fixing allows
it to be fixed to the wall rather than the
plasterboard. Always check the fixing
is secure to the retaining wall.
For use when attaching light loads on
to plasterboard partitions.
For use when fitting or supporting
heavy loads such as shelving, wall
cabinets and coat racks.
For use with heavier loads such as TV
& HiFi speakers and satelite dishes etc.
No.1 “General Purpose” wall plug No.3 “Cavity Fixing” wall plug No.5 “Hammer Fixing” wall plug
No.2 “Plasterboard” wall plug
No.4 “Cavity Fixing-Heavy Duty”
wall plug
No.6 “Shield Anchor” wall plug
Heavy loads
A Guide to Wall Mounting & Fixings
Care &
Maintenance
Safety: Always check the fitting
and location to ensure your safety
in and around the home.
Fitting: From time to time check
the fitting to ensure the wall plugs
or screws do not become loose.

17
18
Gx 4
7
Finished
front edge

19
20
Kx 4
Hx 8
https://www.youtube.com/watch?v=b4NeCGnpjP8
Pre-mounted Hinge Fitting & Adjustment
8
8
Press the screws into the holes in the panels
When the hinges have been pushed in,
tighten up their screws
Repeat for both doors

a:
b:
a: Height adjustment.
Loosen screws A on Hinge Plates and
move Door up or down as required.
Retighten screw A.
21
https://www.youtube.com/watch?v=b4NeCGnpjP8
Pre-mounted Hinge Fitting & Adjustment
c:
A
A
B
C
Adjust the Door if required
b: Forward and Back adjustment.
Loosen screw B on Hinge Plate and
move door in or out as required.
Retighten screw B.
c: Sideways adjustment.
To move door ‘out’ loosen screw C.
To move door ‘in’ tighten screw C.
22 Ix 4
Assembly is complete
Please remove any blue protective film from panel
edges and clear protective film from panel surfaces
ALR3670