Argos Home New Pagnell 601/9435 User manual

New Pagnell 2 Dr 2 Drw Wardrobe
Assembly Instructions -
Please keep for future reference 601/9435
Dimensions
Depth - 54.5cm
Width - 76cm
Height - 180.5cm
601/6524
Important - Please read these instructions fully before starting assembly
Version 1 Date: 08/11/16
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
601/8436

Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Safety and Care Advice
Important –Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
Handy Hints
• Do not use this item if any
components are missing or
damaged.
• Parts of the assembly will be
easier with 2 people.
• Argos Ltd. MK9 2 NW. • This product is intended for
children in the age 6 or above.
• Maximum load:
50 kgs (inside of wardrobe).
• Assembly of this product must
be carried out by a competent
adult.
IMPORTANT: RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE
• During assembly children
should be kept away from the
product due to possible risk of
injury.

2
Right side panel (179 x 52cm)
2
Left side panel (179 x 52cm)
3
Pilot holes for guidance only
Pilot holes for guidance only
Top panel (76.2 x 54cm)
1
Middle panel (73 x 51.9cm)
4
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800

3
Bottom support (73 x 11cm)
6
Bottom panel (73 x 11cm)
5
Front panel (73 x 7cm)
7
Middle support (73 x 11cm)
8
Drawer front panel x 2 (72.3 x 14.4cm)
10
Drawer back panel x 2 (69.8 x 11.5cm)
11
Drawer left side panel x 2
(34 x 11.5cm)
13
Drawer right side panel x 2
(34 x 11.5cm)
12
Drawer bottom panel x 2
(70.7 x 33.6cm)
14
Door x 2 (138.2 x 36.1cm)
9
Back panel (75.8 x 173.2cm)
15
Pilot holes for guidance only
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800

4
Note: The quantities below are the correct amount to complete the assembly. In some cases mor
may be supplied than are required.
Components - Fittings
N
Nail x 30
(This screw is included
in the bag of runner)
A
Runner x 4
B
12mm Screw x 12
C
Door hinge x 6
D
15mm Screw x 24
(This screws is included in
the door hinge bag) E
Rail Support x 2
F
39mm Locking pin x 18
G
30mm Dowel x 14
H
Door stop x 2
I
20mm Screw x 4
J
Plastic support x 3
K
14mm Screw x 8
L
15mm Locking nut x 10
M
50mm Screw x 6
O
12mm Locking nut x 8
P
30mm Screw x 8
Q
Clothes rail x 1
R
12mm Screw x 4
S
Door pad x 4
U
Wall strap x 2
(This screw is
included in the
wall strap bag)
x 2
V
Wall plug x 2
W
Glue x 1
T
15mm Screw x 4
Ruler - Use this ruler to help correctly identify the screws
Tools required
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
7mm Suitable drill bit
(for use with wall plug)
The screws length is measured from the head to the point (30mm screw shown).
X
Ventilation holes cover x 2

5
a:
Assembly Instructions
Step 1
b:
Attaching runners and
hinges
B
2
A
2
B
B
A
a:
Position Runners
in front edge of the Right
side panel .
Slide top of the Runner
back.
Runners on the Right
side panel .
A
B
A
2
Door hinges ‘back
plates’ onto the Right
side panel .
C
D
2
Rail support on the
Right side panel .
T
E
2
Middle hole
Middle hole
T
E
Continued on next page.
A
A
B
B
D
D
D
T
C
C
C
E
Pilot holes for
guidance only
Finished
front edge
B
B
B
B
2
2
2
1.7cm
Note: The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
A
b: Slide top of Runners
forward and
A
B
.
A
A
D
C

B
B
B
B
3
6
c:
Assembly Instructions
Step 1 - continued
d:
Door hinges ‘back
plates’ onto the Left side
panel .
C
D
3
Rail support on the
Left
side panel .
T
E
3
T
E
A
BB
3Middle hole
A
B3
Middle hole
E
T
D
D
D
C
C
C
A
A
B
B
Pilot holes for
guidance only
back edge
3
1.7cm
Note:
The front part of
the runner should be
approximately 1.7cm
from the front edge of the
panel.
c: Position Runners in
front edge of the Left
side panel .
3
Runners on the Left
side panel .
A
Slide top of the Runners
A
A
B
3
.
d: Slide top of Runners
forward and
A
B
.
A
A
Pilot holes for
guidance only
D
C

7
Assembly Instructions
Step 2
Step 3
Fitting locking pins
Screw Locking pins
into the Right side panel
and Left side panel
.
F
Note:
Insert locking pins
as far as shown.
Do not over tighten.
3
2
Fitting dowels
F
F
F
F
F
F
F
F
F
F
F
2
3
56
4
G
G
G
G
G
G
G
G
G
G
G
G
H
I
6
Insert Dowels into the
Bottom panel ,
Bottom support ,
Middle support and
Middle panel .
G
8
5
4
4
Stop onto the Middle
panel .
H
I
H
I
8

Step 4
Step 5
Assembly Instructions
8
b:
a:
Note:
2 people are need
at this stage.
Position Front panel
and Bottom panel
onto the unit.
Attaching front panel
Attaching plastic
supports
a:
Plastic supports onto
the Front panel .
K
7
J
b:
Front panel onto the
Bottom panel .
K
7
5
K
J
back surface
K
J
7
K
J
K
J
K
K
K
7
5
Insert Locking nuts
into the Bottom panel
.
Use a screwdriver to turn
Locking nuts clockwise
to lock.
L
L
L
5
2
K
7
5
7
5
L

Step 6
Assembly Instructions
9
back edge
Note:
2 people are
needed at this stage.
Position Middle panel
onto the unit.
Insert 2 Locking nuts
into the Middle panel .
Use a screwdriver to turn
Locking nuts clockwise
to lock.
L
L
Attaching middle panel
Insert 2 Locking nuts
into Middle support
and Bottom support .
Use a screwdriver to turn
Locking nuts clockwise
to lock.
L
L
Step 7
Attaching back
support and bottom
support
L
L
2
8
6
4
4
Position Middle support
and Bottom support
onto the unit.
6
8
6
8
L
2
L
L
4
back edge
L