Argos Verona 609/5033 User manual

Assembly Instructions - Please keep for future reference
Dimensions
Width - 90cm
Depth - 45cm
Height - 41cm
Important - Please read these instructions fully before starting assembly
Verona Coffee Table
issue 1 4/23/10
609/5033
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
610/6812

We do not
recommend the use
of power drill/ drivers
for inserting screws,
as this could damage
the unit. Only use hand
screwdrivers.
Warning: The unit weighs
approximately 7.4kgs.
Please lift with care.
●Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
●From time to time check that
there are no loose screws on this
unit.
●This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
1
Safety and Care Advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
Check you have all the
components and tools listed on
pages 2 and 3.
plastic bags and separate them
into their groups.
Remove all fittings from the
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand on the panels, this
could cause damage.
Assemble the unit as close to its
final position (in the same room)
as possible.
Assemble on a soft level
surface to avoid damaging the unit
or your floor.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging carefully
and responsibly.

Components - Panels
Please check you have all the panels listed below
2
Table top (90 x 45cm)
1
Post x 4 (37.1 x Ø3.5cm)
3
Foot x 4 (4.7 x 3.4cm)Ø
4
Shelf (70 x 35cm)
2
If you have damaged or missing components,
call the Customer Helpline:08456 400800
Cap screw x 4
Components - Fittings
Please check you have all the fittings listed below
Ruler - Use this ruler to help correctly identify the screws
A
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
Pre-assembled at 4

Assembly Instructions
Step 1
Fitting the legs a:
4
A
Step 1
a: Unscrew Cap screws
a from the Feet .
A4
b: Use Legs to fix the
Feet onto the Shelf
2 .
3
b:
c:
2
2
3
4
4
1
A
c: Use Cap screws to
fix the Top panel onto
the unit.
1
A
3

Assembly Instructions
Assembly is complete.
Finally place the unit in
the desired location.
Step 2
Finishing the unit
Note: Before use always
make sure the unit is
secure.
If you need help or have damaged or missing parts, call the Customer Helpline : 08456 400800
4

Simple Assembly Instructions - Please keep for future reference
IMPORTANT
1. Read these instructions carefully and
familiarise yourself with the procedure
before assembling the unit.
2. Check that you have all the component
parts following the list on the back
cover and familiarise yourself with
each part before proceeding.
3. Take all the fittings out of the plastic bag
and separate them into their groups.
4. Ensure you have enough space to lay out
all the parts before assembly.
Verona Beech / Silver Coffee Table
Components
5. To avoid scratching it is recommended
that you assemble the unit on a soft
level surface.
Fittings
8-03
A4 x Cap Screw
1 x Table Top
A
1 x Shelf
B
4 x Leg
C
4 x Foot
D

Assembly Instructions Assembly Instructions
Stage 2 – Finishing the Unit
Care and Maintenance
Stage 1 – Fitting the Legs
Safety
To avoid any risk of suffocation to animals or children dispose of the plastic
bags immediately.
Fitting
From time to time please ensure there are no loose screws on the product.
Cleaning
As with all surfaces clean with a damp cloth and mild detergent, do not use bleach
or abrasive products.
1. Finally place the unit in the desired
location.
See fig. 3.
fig. 3
fig. 3
fig. 1
D
2. Use Legs C to fix the Feet D
onto the Shelf B.
See fig. 2.
3. Use Cap Screws A to fix the
Table Top Aonto the unit.
See fig. 3.
1. Unscrew Cap Screws Afrom the
Feet D.
See fig. 1.
A
A
fig. 2
B
D
C
A