Argos Alfie User manual

Ale - Cabin Bed
Dimensions
Width - 195cm
Depth - 95.5cm
Height - 53cm
Issue 1 - 9/30/13
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Assembly Instructions - Please keep for future reference
167/8527
162/4698

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: if required the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your oor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• WARNING: Do not place this child`s bed near heat
sources, windows and other furniture.
• WARNING: Do not use this child`s bed if any part is
broken, torn or missing.
• WARNING: Not suitable for children under the age of
4 years.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below

Components - Panels
Please check you have all the panels listed below
2
Front bed board (192 x 55.5cm)
1Left bottom panel (63.5 x 30.05cm) 9
Right bottom panel (32 x 30.05cm)
10
Shelf (32 x 30.05cm)
11
Front central support (93.5 x 11cm)
12
Left shelf partition (53.2 x 37.2cm)
13
Right shelf partition (53.2 x 37.2cm)
14
Back bed board (192 x 40cm)
2
Front side frame (192 x 11cm)
3
If you have damaged or missing components,
call the Customer Helpline:
08456 400800
Back side frame (192 x 11cm)
4
Front/Back bed support x 2 (192 x 14.3cm)
5
Front panel (192 x 4cm)
6
Large central support (63.5 x 37.2cm)
7
Small central support (32 x 37.2cm)
8

3
Components - Panels
Please check you have all the panels listed below
Left side panel (95.5 x 53cm)
15
Drawer front panel x 2 (96.4 x 16cm)
17
Drawer back panel x 2 (88 x 11.6cm)
18
Drawer bottom panel x 2 (91 x 33.6cm)
19
Drawer left side x 2 (34 x 9.8cm)
20
Drawer right side x 2 (34 x 9.8cm)
21
Drawer bottom support x 2 (32.5 x 6cm)
22
Right side panel (95.5 x 53cm)
16
If you have damaged or missing components,
call the Customer Helpline:
08456 400800

Please check you have all the ttings listed below
50mm wood screw x 22
Ruler - Use this ruler to help correctly identify the screws
Tools required
A
Screw-in dowel x 6
E
50mm xing screw x 44
B
16mm wood screw x 26
H
30mm wooden dowel x 12
C
13mm xing screw x 12
I
Note: The quantities below are the correct amount to complete the assembly. In some cases more ttings
may be supplied than are required.
100 20 30 40 50 60 70 80 90 100
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Cap x 6
F
Locking nut x 6
D
Left inside runner x 2
Plastic support x 7
Nut x 6
K
N
Q
Shelf support x 4
G
Left outside runner x 2
J
Components - Fittings
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
Wrench №10
Right outside runner x 2
Allen key x 1
Support leg x 2
L
O
R
Right inside runner x 2
25mm carriage bolt x 6
M
P
4

Assembly Instructions
Step 1
Step 2
Attaching runners
Two people are needed
here.
Position runners J 2mm
in from front edge of the
left shelf partition 13 and
runners L 2mm in from
front edge of the right
shelf partition 14 .
Fix through holes shown
using 13mm xing screw
I .
Assemble middle
modul
a: Screw the left shelf
partition 13 and the right
shelf partition 14 to the
front central support 12
through 50mm xing
screw B.
Note: Use the Allen Key
O.
5
Finished
front edge
Finished
front edge
J
J
J
L
L
I
I I I
I
I
I
I
I
I
I
I
I
I
I
14
13
13
B
B
13
14
12
Clockwise
B
O

6
b:
Assembly Instructions
Attaching panels
Two people are needed
here.
Position the left bottom
panel 9 to the left shelf
partition 13 and the right
bottom panel 10 to the
right shelf partition 14 .
Use 50mm xing screw
B.
Attaching panels
Two people are needed
here.
a: Insert the 30mm
dowels C to the left
shelf partition 13 and to
the right shelf partition
14 like shown on the
drawing.
b: Position the large
central support 9 to the
left shelf partition 13 and
the small central support
10 to the right shelf
partition 14 .
Fix the panels through
50mm xing screw B.
Step 4
Step 3
13
13
9
10
14
14
C
C
B
B
Clockwise
9
13
14
10
B
B
B
O
Clockwise
B
O
a:

Assembly Instructions
c: Fix the large central
support 9 and the
small central support
10 through 50mm xing
screw B.
Note: Use the Allen Key
O.
Step 5
Attaching panel
a: Screw plastic
supports N to the front
panel 6 through 16mm
wood screws H.
Note: Use the guidance
pilot holes.
Rotate the construction
of the bed horizontally at
180 degrees.
b: Position the front
panel 6 and screw it
to left bottom panel 9
, front central support 12
and right bottom panel
10 through 16mm wood
screws H.
Note: Use the guidance
pilot holes.
7
9
10
B
B
B
c:
a:
b:
HH
H
H
H
H
H
H
H
H
H
H
H
H
H
N
N
N
N
N
N
N
N
6
6
10
12
9
Step 4 - continued
180
Clockwise
B
O

Assembly Instructions
Attaching panels
Position the front side
frame 3 to the left shelf
partition 13 and the right
shelf partition 14 and x
it through 50mm xing
screw B.
Attaching panels
a: Insert the 30mm
dowels C to the left
side panel 15 and then
position it to the large
central support 7 and
the front side frame 3 .
b: Fix the left side panel
15 through 50mm wood
screws A.
Note: Use the Allen Key
O.
Step 7
Step 6 B
B
B
B
3
14
13
a:
b:
15
15
3
7
C
C
A
A
O
A
A
A
8
15
Clockwise
B
O

Assembly Instructions
b: Fix the left side panel
15 and the right side
panel 16 through 50mm
wood screws A.
Note: Use the Allen Key
O.
Step 8
C
A
A
A
A
A
A
C
C
C
15
15
16
16
4
3
8
10
b:
a:
Attaching panels
Two people are needed
here.
a: Insert the 30mm
dowels C to the left side
panel 15 and the right
side panel 16 .
First postition the back
side frame 4 to the left
side panel 15 and while
holding the back side
frame 4, position the
right side panel, following
the guidance lines of the
dowels C.
9
16
A
O