Argos Dalton 246/6422 User manual

MADE IN
BRITAIN
Dimensions
Width - 90cm
Depth - 40cm
Height - 87cm
Dalton - 4 Drawer Chest
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 23/06/14
Important - Please read these instructions fully before starting assembly
ALR3039
246/6422
226/3113
257/8767
Issue 2 - 23/06/14 - The F63 Screws used in Step 27 are now fitted into the 1st hole on the Runners to avoid clashing with the Cams.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 36kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 1, 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)

Components - Panels
Please check you have all the panels listed below
2
12 3
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Left End (DF696)
(851 x 365mm)
Top (DF698)
(900 x 396mm)
Left Internal
End (DF703)
(771 x 365mm)
Rail (DF701)
(866 x 80mm) x 2
Plinth (DF957)
(866 x 80mm)
Right Internal
End (DF956)
(771 x 365mm)
4
Right End (DF697)
(851 x 365mm)
5
Pilaster (DF702)
(851 x 88mm) x 2
13
6
78
Drawer Back (W672-124)
(672 x 124mm) x 4
Drawer Base (T683-347)
(683 x 347mm) x 4
Back (X797-892)
(797 x 892mm)
Left Drawer Side (W350-124LH)
(350 x 124mm) x 4
Right Drawer Side (W370-124RH)
(370 x 124mm) x 4
9
10
11
12
14
Drawer Front (DF700)
(716 x 188mm) x 4

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 14
B
Metal dowel (F901) x 30
C
D
Large locking
nut (F900) x 22
E
Small locking
nut (F3) x 8
F
G H I
Nail (F51) x 22
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J K
Knock-in Peg (F171GY) x 16
L
Wedgefix (F639) x 16
13mm Screw (F63) x 24
13mm Screw (F52) x 24
M
Handle (F287) x 8
N
Bracket (F327) x 1
PR Runner (F160) x 4
b
L Runner (F161) x 4
Pc
L Runner (F159) x 4
Pa
R Runner (F162) x 4
Pd
350mm long
19mm Screw (F461) x 16
13mm Screw (F79) x 1
Plastic Nail (F91) x 4
O
Q
50mm Screw (F49) x 4
Allen Key (F36) x 1

Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
80%
x 2
x 4
x 4
x 4
x 4
B
B
B
F
F
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the small groove is on the inside, as shown.
FF
910
Step 2
Prepare the 4 drawer
fronts
Screw 2 metal dowels
into each of the drawer
fronts .
Note: Tighten the metal
dowels up fully against
the panels.
B
8
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
F
9
10
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
9
10
8
F
F
9
10
B
B
8
8
9
10

Assembly Instructions
5
Step 4
C
C
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
12
9 10
8
11
9 10
12
11
11
C
Attach the handles
Attach a handle to
each of the drawer fronts
. using screw .
Note: Do not
overtighten the screw.
H
8
9 10
Step 7
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 4 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
L
x 4
x 4
x 4
C
C
x 4
L
L
L
L
L
12
9
11
9
10
12
10
8
H
H
M
M
H
H
M
8

6
Fit runners to the
drawers
Fit runner , marked
with ‘R’, to the bottom
edge of the right drawer
side , as shown,
making sure that it is
pushed up against the
back of the small drawer
front . Use a bradawl
to mark the fixing
positions, then secure
with 2 screws .
Fit runner , marked
‘L’, to the bottom edge
of the left drawer side
using the same method.
9
P d
10
8
I
P c P d
R
R
I
I
I
I
L
P c
L
Runners must be
pushed up against
the drawer front
Assembly Instructions
Step 8
9
10
x 2
Prepare the 2 palisters
Screw 6 metal dowels
into each of the 2
palisters .
B
13
B
B
BB
BB
Step 9
13

A
A
A
A
Assembly Instructions
7
Step 10
Prepare the left end
Tap 2 wooden dowels
into the left end .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 3 large locking
nuts into the left end
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Screw 3 metal dowels
into the left end .
Step 11
B
1
B
E
E
E
E
BB
E
1
1
10mm
A
1
A
B
BB
E
E
E
Prepare the right end
Tap 2 wooden dowels
into the right end .
Insert 3 large locking
nuts into the
right end .
Screw 3 metal dowels
into the right end .
B
2
E
2
2
A
2

8
Assembly Instructions
Step 12
Step 13
E
B
Fit the left end to a
palister
Push the left end
onto a pallister .
Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the left end .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Note: Dowels
this end
1
13
E
1
E
1
13
Fit the right end to a
palister
Push the right end
onto a pallister .
Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the right end .
2
13
E
2
2
13
Note: Dowels
this end

A
A
Assembly Instructions
9
Step 14
Prepare the left
internal end
Tap 2 wooden dowels .
into the left internal end
. .
Insert 5 large locking
nuts into the
left internal end .
E
E
E
E
E
A
3
E
3
3
Step 15
A
A
E
E
E
E
E
4
Prepare the right
internal end
Tap 2 wooden dowels .
into the right internal end
. .
Insert 5 large locking
nuts into the
right internal end .
Step 16
A
4
E
4
Fit the left internal
end to the palister
Push the left internal end
. onto the pallister
fitted to the the left end
. .
Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the left internal end .
313
1
E
3
Note: Dowels
this end
1
13
3
1