Argos Hygena Genoa 464/2718D User manual

Hygena Genoa Slatted Display Unit
Dimensions
Width - 75cm
Depth - 31.4cm
Height - 152.2cm
Issue 1 - 16/09/15
Important –Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Assembly Instructions- Please keep for future reference 464/2718D

1
Note: if require the next
page can be cut out and used
as reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• Remove all fittings from the
plastic bags and separate them
into their groups.
Safety and Care Advice
Important– Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 3 & 4.
• Keep children and animals
• Make sure you have enough
space to layout the parts before
starting.
away from the work area, small
parts could choke if swallowed.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance

Components- Panels
Please check you have all the panels listed below
Bottom panel
(750 x 300 mm)
1
Leg x 4
(60 x 130 mm)
2
(750 x 300mm)
3Top panel
Left side panel
(1340 x 300mm)
4
Right side panel
(1340 x 300mm)
5
(409 x 240mm)
6Lower divider
Rear panel
(735 x 430mm)
7
Lower fixed shelf
(711 x 300mm)
16
Left side door
(360 x 402mm)
10
Right side door rail
(402 x 61mm)
11
Adjustable shelf x 2
(347 x 238mm)
8
(351 x 402mm)
9Right side door
(60 x 122mm)
12 Center leg
Upper divider
(916 x 299mm)
13
Left fixed shelf x 2
(348 x 299mm)
14
(348 x 299mm)
15 Right fixed shelf x 2
16
10
11
13
14
14
15
15
12
1
2
2
2
2
3
4
5
6
7
8
8
9
2

Components- Panels
Please check you have all the panels listed below
Bottom panel
(750 x 300 mm)
Leg x 4
(60 x 130 mm) (750 x 300mm)
123Top panel
Left side panel
(1340 x 300mm)
Right side panel
(1340 x 300mm) (409 x 240mm)
456Lower divider
Rear panel
(735 x 430mm)
Adjustable shelf x 2
(347 x 238mm) (351 x 402mm)
7
Lower fixed shelf
(711 x 300mm)
16
Left side door
(360 x 402mm)
10 Right side door rail
(402 x 61mm)
11
89Right side door
(60 x 122mm)
12 Center leg
Upper divider
(916 x 299mm)
Left fixed shelf x 2
(348 x 299mm) (348 x 299mm)
13 14 15 Right fixed shelf x 2
3

Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Components- FittingsIf you have damaged or missing components,
call the Customer Helpline: 03456 400800
Please check you have all the fittings listed below
50mm Screw
x
x
5
A
B C
14 mm Screw x 20
D
E
Metal cam x 24
F
Shelf pin
x
8
Ruler- Use this ruler to help correctly identifythescrews
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100
110 115 120 125 130 135 140 145 150 155 160 165 170
105
Metal dowel
x
G
H I
J
Tools required
Phillips screwdriver
(medium & small)
Flatblade screwdriver
Small wood dowel x 36Cover pad x 28
40mm Screw
12
x
25mm Screw
4
K
Adjustable foot
Large wood dowel x 10
L
Webbing and screw x 2
4
24

Assembly Instructions
Step
1
Lay Upper divider and
Left fixed shelves on
their long edges on a flat
soft surface as the
direction shown.
Push Upper divider
onto the wood dowels in
Left fixed shelves and
fasten using 40mm
Screws .
Step
2
13
13
14
14
14
13
H
H
H
Push Wood dowels
into ends of Upper
divider .
Push Lower fixed shelf
onto the wood dowels
and fasten using 40mm
Screws .
H
I
I
Push Small wood dowels
into indicated holes in
the shelves.
I I
Cam holes in the top
right of Upper divider.
Cam holes underneath
the Left fixed shelves.
Cam holes underneath
the Left fixed shelves.
13
16
16
5

shelves on to the
Upper divider ,
ensuring the Metal
dowels and wood
dowels enter
corresponding holes.
13
C
C
I
Assembly Instructions
Step
3
Step
5
Screw 6 Metal dowels
into the threaded holes in
Upper divider and Lower
fixed shelf.
C
Insert the 4 Metal Cams
into the 4 holes on
the Panels so that
they are flush.
Note: Longer
leg of the cross
on the Metal
Cams must face towards
end of panel (as shown).
Then, using a Philips
Screwdriver, screw all
Metal Cams
clockwise until they are
‘hand tight’.
D
15
D
Step 4
dowels and wood
dowels enter
C
A
Insert Small wood dowels
into the center holes
in Upper divider.
I
Firmly push Right fixed
D
Note: Longer leg of
the cross on the
Metal Cams must
face towards end
of panel.
I
D
16
15
15
15
13
6

C
ensuring the Metal
dowels and wood
dowels enter
corresponding holes,
secure with Metal cams
.
C
I
D
D
Step
6
Step
7
Assembly Instructions
dowels and wood
dowels enter
C
A
Insert Small wood dowels
into the middle holes in
Shelves .
I
Firmly push the side
panels onto the
ends of the shelves,
Grooves in the rear edge
of side panels for rear panel.
4
4
4
4
5
5
5
Screw 6 Metal dowels
into the threaded holes in
C
14
14
15
15
16
16
Left side panel .
Screw 6 Metal dowels
into the threaded holes in
C
Right side panel .
5
7

C
D
D
Holes in the rear edge for
securing on to the wall in
the last step.
Holes in the rear edge for
securing on to the wall in
the last step.
4
6
6
3
3
5
Assembly Instructions
Step
8
Step
10
Screw 6 Metal dowels
into the threaded holes in
Top Panel as
shown.
C
3
Step 9
dowels and wood
dowels enter
corresponding holes.
C
A
Insert Small wood dowels
into the middle holes in
Side panels and Dividers.
I
Firmly push the Top
Panel onto the ends
of the panels and
, ensuring the Metal
dowels and wood
dowels enter
corresponding holes,
secure with Metal cams.
C
3
13
4 5
I
dowels and wood
dowels enter
corresponding h
C
A
Insert Small wood dowels
into the middle holes in
Lower fixed shelf .
I
I
I
Firmly push the Lower
divider onto the
dowels and secure with
Metal cams.
13
16
16
8

Push Wood dowels
into ends of side
panels and .
Push Bottom panel
onto the wood dowels in
the end of panels and
fasten using 40mm
Screws .
4
4
5
5
1
1
6
6
H
H
I
I
Adjustable foot in
the bottom.
Step
11
Step
13
Assembly Instructions
Step 12
Lay Bottom Panel on
its long edge on a flat
soft surface.
Screw Adjustable foot
into the bottom hole of
Center leg . You can
adjust the foot to make
sure the unit is stable
when the assembly is
complete.
Push Legs onto the
corner wood dowels in
Bottom panels and fasten
using 50mm Screws .
Repeat this step to
secure Center leg in
the middle of bottom
panel.
1
1
2
2
2
2
12 12
12
12
2
B
B
Push Large wood dowels
into indicated holes in
Bottom panel.
A
A
K
K
Turn the unit upright,
cover all visible cam
holes with Cover pads .
G
9

Push 4 Shelf Pins
into each side of the
side panels and divider
at desired height.
E
Tape.
Unfold Rear Panel .
Secure the Rear Panel
into the rear edges
of side panels, lower fixed
shelf and bottom panel
using 14mm Screws .
Note - make sure
unit is square
before securing
rear panel in place.
7
7
F
Measure on the back
across the 2 diagonals
to make sure unit is
square.
Y
X
7
F
Assembly Instructions
Step
14
Step
15
10

8
Taped edge.
Pin
2 people needed for this step.
Step
16
Step
17
Assembly Instructions
9
Insert the bottom rollers
of Door in the inner
groove in the bottom
panel, holding the door
and push the top edge to
line up with the inner
groove in lower fixed
shelf.
Push the release button
to release the pin into the
top inner groove.
Make sure the pin in the
top lock in the Door
is down, if not, push it
down until it locks.
9
9
Place adjustable
shelves onto the
Shelf Pins.
8
11
Release button

11
J
Assembly Instructions
Step
18
Step
19
Insert the bottom rollers
of Door in the outer
groove in the bottom
panel, holding the door
and push the top edge
to line up with the outer
groove in lower fixed
shelf.
Push the release button
to release the pin into the
top outer groove.
Make sure the pin in the
top lock in Left side
door is down, if not,
push it down until it locks.
10
10
Secure Right side door
rail on to the Right
side door using
Screws from the
counter sunk hole as
shown.
Cover the visible screw
holes with Cover pads .
11
J
G
9
12

Step
20
If you need help or have damaged or missing parts, call the Customer Help Line: 03456 400800
Home Retail Group plc. Avebury, 489-499 Avebury Boulevard. Milton Keynes. MK9 2NW
Assembly Instructions
Assembly is complete.
Note: This Step
is for securing
the Unit to a
wall and should only be
attempted by
experienced persons.
You willNeed the
Following:
- Another person to
assist you
- Electric Drill (& Drill
Bits)
- Screwdriver
Note: The
fixings
described are
for use with solid
masonry walls only.
Alternative fixings should
be purchased if you have
a different wall
construction.
Fixings Supplied:
- 2 Webbings
- 2 Small Wood
Screws
-
2 Large Wall Screws
- 2 Wall Plugs
13