Argos Seville 147/4556 User manual

Assembly Instructions - Please keep for future reference
Ruler - Use this ruler to help correctly identify the screws
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
MADE IN
BRITAIN
If you need help or have damaged or missing parts, call the Customer Helpline: 0870 112 1928
or email: [email protected] (quoting your original order number)
Important - Please read these instructions fully before starting assembly
Dimensions
Issue 3 - 21/01/15
Width - 102.5cm
Depth - 49.5cm
Height - 175.5cm
Seville - 3 Door Robe
ALR2909
147/4556
167/8338
173/6146
171/6939
Issue 2 - 04/09/14 - Round Back Holders replaced with Oblong Back Holders.
Issue 3 - 21/01/15 - Overbalance Bracket replaced with Strap.
Back Holders now shown being fitted vertically.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 59kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.

2
80%
x2
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
[email protected] (quoting your original order number
and the reference numbers below)
1 2
Left Side (D2483A)
(1753 x 496mm)
Right Side (D2497A)
(1753 x 496mm)
Upright (D2500A)
(1640.5 x 477mm)
Door (D2487A)
(1652 x 327mm) x 3
Small Back (X1666-332)
(1666 x 332mm)
Large Back (X1666-685)
(1666 x 685mm)
Shelf (D2501A)
(313 x 475mm) x 2
3
Plinth (D2502A)
(995 x 80mm)
Top (D2498A)
(995 x 495mm)
Base (D2499A)
(995 x 480mm)
4
5
6
7
9
10
11
Hanging Rail (FHR659)
(659mm long)
8

3
Rule
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Step
ladder
Ruler - Use this ruler to help correctly identify the screws
Electric drill
(only use
when drilling
into walls)
Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
[email protected] (quoting your original order number
and the reference numbers below)
A
Wooden dowel (F22) x 6
B C
D E F
G H I
Nail (F51) x 36 40mm Screw (F910) x 14
K
L M
Hinge plate
(F523) x 9 Hinge (F522) x 9
13mm Screw (F63) x 20
Rail holder
(F1014) x 2
Handle (F300) x 3
25mm Screw (F95) x 3 Shelf support (F121) x 8
Nail screw (F277) x 5
J
Back holder (F276) x 5
*These can also be round
Strap
Screw Washer x 2
Overbalance protector kit (F269) x 1
Important: Always pair up
the hinges with the hinge
plates from the same bag.
DO NOT mix them up.

4
F
Step 1
Assembly Instructions
If you have damaged or missing components, call the
Customer Helpline: 0870 112 1928 or email:
[email protected] (quoting your original order number
and the reference numbers below)
A
Step 2
10mm
A
Prepare the top and
base
Tap 2 wooden dowels
into the top .
Tap 2 wooden dowels
into the base .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
A
A
4
5
A
4
A
A
5
plain chipboard surface
Prepare the upright
Push a rail holder into
the upright . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Fit 3 hinge plates onto
the upright , making
sure that the slot is
facing towards the
finished front edge.
H
3
L
3
L
L
L
L
H
F
Finished
front edge
F3
Finished
front edge
Finished
front edge

Finished
front edge
Finished
front edge
Finished
front edge
C
C
Assembly Instructions
5
Step 3
Fit the top and the
base to the upright
Fit the top and the
base onto the upright
. using 4 screws .
C
C
3
4
5
plain chipboard surface
4
5
3C
Step 4
Prepare the right side
Fit 3 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
L
2
2
L
L
L
L
2
Finished
front edge

6
Finished
front edge
1
L
Prepare the left side
Push a rail holder into
the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
Fit 3 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
H
1
L
1
L
L
L
H
F
1
F
Assembly Instructions
Step 5
Step 7
C
C
C
C
2
Fit the right side
Push the right side
onto the top and
base and secure it
using 4 screws .
2
4
5
4
5
C
Step 6
A
Prepare the plinth
Tap 2 wooden dowels
into the plinth .
6
A
A
Plain chipboard
6

C
Assembly Instructions
7
Step 8
Step 9
Fit the plinth
Push the plinth onto
the right side and
secure it using screw .
6
2
2
C
Note: Support the plinth
until the left side has been
fitted in the next step.
6
Finished
front edge
C
1C
C
C
C
Fit the left side
Push the left side
onto the assembly and
secure it using 5 screws
. .
1
C

8
Assembly Instructions
Step 10
b:
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
Place the small back
and large back down
onto the unit as shown.
Make sure that
the 2 backs are
pushed up tight
against each
other and that
they meet over
the back edge of
the upright.
b: Nail around
the outside edges
of the 2 backs.
Note: Do not nail where
the backs meet. Nails
should be spaced about
150mm apart.
10
11
B
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
y
y
x
x
B
Warning: The
unit is heavy.
Lift with care.
10
11
Step 11
Secure the backs
Tap the nail screws
through the back holders
. and down between
the backs and
into the back edge
of the divider.
Keep tapping the
nail screws in
until the back
holders dig
into the small
and large back.
Stand the unit up for
the next step.
K
J
10 11
K
J
10
11
KJ +x 5
Note: Do not
nail where the
backs meet.
K
J
J
Note: These can
also be round

Assembly Instructions
9
Step 12
Ex 4
Ex 4
8
H
Fit the hanging rail
and the shelves
Push hanging rail into
the rail holders fitted
to the side panels.
For each of the 2
shelves , insert 4 shelf
studs at the required
height.
Lower the 2 shelves
down onto the shelf
studs .
8
H
8
Make sure that the plastic
sleeve is fully pushed
onto the shelf stud.
E
7
E
7
L
7
7
Step 13
Prepare the 3 doors
Push fit 3 hinges into
each of the the doors
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
F
M
9
90
M
.x 3
M
F
F
M
F
F
M
F
F
9