Argos Kensington 411/7542 User manual

MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
Kensington - 3 Door Mirror Robe
Assembly Instructions - Please keep for future reference
ALR3174
411/7542
413/6949
Width - 125.6cm
Depth - 49.5cm
Height - 198.8cm
Issue 1 - 16/06/15

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 93kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
overbalance protector kit
supplied or, an alternative fixing
method of your choice.
• Dispose of all packaging
carefully and responsibly.
Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Top (DF3757)
(125.6 x 49.5cm)
Base (DF3765)
(119.4 x 47.4cm)
Inner Top (DF3766)
(119.4 x 47.4cm)
Wide Shelf (DF3761)
(79.7 x 45cm)
1 2
3 4 Narrow Shelf (DF3764)
(38.2 x 45cm) x 4
5

Components - Panels
Please check you have all the panels listed below
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
2
80%
Front Plinth (DF3762)
(125.6 x 9.2cm)
Rail (DF3760)
(119.4 x 9.2cm) x 2
Side Plinth (DF2431)
(47.5 x 9.1cm) x 2
Plain Door (DF3767)
(184.5 x 39.4cm) x 2
Mirror Door (DF5210)
(184.5 x 39.4cm)
(Mirror - SG29
177.6 x 30cm
Safety Back SAR)
Small Back (X1892-401)
(189.2 x 40.1cm)
Large Back (X1892-816)
(189.2 x 81.6cm)
Left Side (DF3758)
(197.3 x 47.5cm)
6Right Side (DF3759)
(197.3 x 47.5cm)
Divider (DF3763)
(185.1 x 45.1cm)
7 8
10
9
11
13 14 15 16
Hanging Rail (FHR791)
(79.1cm long)
12

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
3
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Tools required
Scissors / Rule / Hammer / Cross-head screwdriver / Square / Spirit level / Step ladder
Eye protection (when using a hammer or drill)
Electric drill (only use when drilling into walls)
A B
D E
G H
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer
Eye protection
(when using a
hammer or drill)
Cross-head screwdriver Step
ladder
Electric drill
(only use
when drilling
into walls)
C
F
P Q
Large locking
nut (F900) x 24
Metal dowel (F901) x 24 Wooden dowel (F22) x 26
Hinge plate
(F523) x 12 Hinge (F522) x 12
I
40mm Screw (F910) x 2 19mm Screw (F461) x 2
Back holder (F276) x 6
*These can also be round
Nail screw (F277) x 6
L
Shelf stud (F110) x 16
N
Handle (F220) x 2
J K
Nail (F51) x 42 Plastic Nail (F91) x 6
13mm Screw (F63) x 28
25mm Screw (F50) x 4
M
Rail Holder
(F891) x 2
OStrap
Screw Washer x 2
Overbalance protector kit (F269) x 1

Assembly Instructions
4
Step 1
C
C
Prepare the divider
a: Screw 2 metal
dowels into the
divider .
Note: Tighten the metal
dowels up fully against
the panels.
Insert 2 large locking
nuts into the
divider .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap 4 wooden dowels
into the divider .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
b: To fit the rail holder
screw through the top
hole with screw and
into the mark hole drilled
in the divider . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
Fit 4 hinge plates onto
the divider , making
sure that the slot is
facing towards the
finished front edge.
A
8
8
C
8
A
G
M
G
M
10mm
C
B
B
M
G
8
G
P
8
b:
a:
B
B
A
A
C
C
Finished
front edge
8
1
G
G
M
Finished
front edge
P
P
P
P
P
8

Finished
front edge
Finished
front edge
C
C
C
C
Assembly Instructions
5
Step 2
Step 3
Prepare the inner top
Screw 2 metal dowels
into the inner top .
Insert 4 large locking
nuts into the inner top
. .
Tap 4 wooden dowels
into the inner top .
3
C
3
B
B
B
B
B
C
C
A
A
Finished
front edge
Important: The inner top is
very similar to the base but,
the inner top will only have
holes on one surface.
3
A
B
Fit the inner top to
the divider
Push the inner top
onto the divider .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the divider .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 4
3
8
B
B
8
3
8
B
BB
B
C
C
Prepare the wide shelf
Insert 4 large locking
nuts into the wide
shelf .
Tap 4 wooden dowels
into the wide shelf .
4
C
4
B
Finished
front edge
A
3
4

Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 5
8
4
Fit the wide shelf
Push the wide shelf
onto the divider .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the wide shelf .
4
8
B
4
C
C
B
B
B
B
C
C
Finished
front edge
2
Step 6
Prepare the base
Insert 4 large locking
nuts into the base .
Tap 4 wooden dowels
into the base .
Step 7
Fit the base
Push the base onto
the divider and
secure it using 2 screws
. .
2
C
2
B
D
D
2
8
D
2
8

C
C
Assembly Instructions
7
Step 8
Prepare the right side
a: Screw 6 metal
dowels into the right
side .
Insert 2 large locking
nuts into the right
side .
b: Tap 2 wooden
dowels into the right
side .
Fit 4 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
A
7
7
C
7
B
b:
a:
B
B
A
A
A
A
A
A
P
P
P
P
Finished
front edge
Finished
front edge
P
7
7
7
Fit the right side
Push the right side
onto the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the base and inner
top .
7
B
2
3
Step 9
7
2
3

Finished
front edge
Finished
front edge
C
Assembly Instructions
8
Step 10
C
C
B
B
P
P
P
P
A
A
A
A
A
A
A
G
G
M
A
Prepare the left side
a: Insert 2 large locking
nuts into the
left side .
Tap 2 wooden dowels
into the left side .
Fit 4 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
b: Screw 8 metal
dowels into the left
side .
To fit the rail holder
screw through the top
hole with screw and
into the mark hole drilled
in the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
A
6
6
C
6
B
M
G
6
G
P
6
b:
a:
6
6
P
B
B
C
Prepare the 2 rails
Insert 2 large locking
nuts into each of the 2
rails .
Tap 2 wooden dowels
into each of the 2 rails .
9
C
9
B
Step 11
9
x 2

Assembly Instructions
9
Step 12
Fit the right side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 8 large
locking nuts fitted to
the base , inner top ,
wide shelf and 2 rails
. .
Step 13
9
9
Fit the 2 rails
Push the 2 rails onto
the assembly.
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the 2 rails .
9
B
9
Note: Support this rail
until the left side has been
fitted in the next step.
9
9
6
B
2 3
4
9
6
2
3
4