Argos 558/8228 User manual

MADE IN
BRITAIN
Dimensions
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Important - Please read these instructions fully before starting assembly
More help is available throughout this
booklet by scanning in the QR codes
or typing in the links
WARNING!
In order to prevent overturning, this product must be
used with the wall attachment device provided
Malibu - 5+2 Drawer Chest
Assembly Instructions - Please keep for future reference
539/6173
544/1341
541/5566
542/1907
558/8228
Width - 74.8cm
Depth - 39cm
Height - 108.6cm
Issue 5 - 06/10/16
CR
CR
CR
CR
CR
CR
CR

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 38kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: To prevent
possible overbalancing this unit
must be secured to a wall
using the overbalance protector
kit supplied or, an alternative
fixing method of your choice.
• Dispose of all packaging
carefully and responsibly.
Tools required
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)
When applicable, remove any protective film
from the panels before they are used

Components - Panels
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
Please check you have all the panels listed below When applicable, remove any
protective film before use
2
12 4
3
5
8
6 7
9 10
11 12 13
14
15
16
17
Left Side (DF6786)
(107.1 x 39.4cm)
Top (DF6780)
(74.8 x 39.6cm)
Large Drawer Front (DF5996)
(70.8 x 15.7cm) x 5
Back Rail (DF5857)
(71.4 x 6cm) x 2
Divider (DF6781)
(16 x 37.3cm)
Plinth (DF5856)
(71.4 x 9.2cm)
Cross Rail (DF5858)
(71.4 x 6cm)
Right Side (DF6787)
(107.1 x 39.4cm)
Small Left Drawer
Front (DF6782)
(35.25 x 15.7cm)
Small Right Drawer
Front (DF6783)
(35.25 x 15.7cm)
Large Drawer Back (W665-130)
(66.5 x 13cm) x 5
Small Drawer Back (W300-130)
(30 x 13cm) x 2
Small Drawer Base (T311-347)
(31.1 x 34.7cm) x 2
Left Drawer Side (WB350-130LH)
(35 x 13cm) x 7
Right Drawer Side (WB350-130RH)
(35 x 13cm) x 7
Large Drawer Base (T676-347)
(67.6 x 34.7cm) x 5
Back (DF6788)
(98.9 x 74cm)

Please check you have all the fittings listed below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Components - Fittings
If you need help or have damaged or missing parts, please visit www.argos-support.co.uk
or email: [e-mail] (quoting your original order number)
Alternatively, call the Spares Helpline on: 0370 112 1928.
For any other queries please contact the Customer Helpline on: 0345 640 2020
3
J
Plastic Nail (F91) x 5
I
9mm Screw (F73) x 42
Drawer Fittings Bag marked ‘drw kit’
Main Fittings Bag
A
Quickfit dowel (F545) x 14
A
Quickfit dowel (F545) x 12
C
Knock-in Peg (F171GY) x 28
D
19mm Screw (F461) x 12
F
13mm Screw (F63) x 14
H
Wooden dowel (F22) x 16
K
Nail (F51) x 24
M
Handle (F418) x 12
336mm long
Large locking cam nut (F607) x 14
B
Large locking cam nut (F607) x 12
B
Drawer Brace (F420) x 5
L
Nb
Na
350mm long
CL
CR
CR Runner (F424) x 7
CL Runner (F422) x 7
Nc
Nd
13mm Screw (F63) x 28
F
Individual Fittings Bags
DR
DL
DL Runner (F425) x 7
DR Runner (F426) x 7
Overbalance protector
kit (F474) x 1
O
G
Wedgefix (F639) x 4
E
15mm Screw (F284) x 10

Assembly Instructions
4
Step 1
Step 2
Fit the drawer sides
to the 5 large drawer
fronts
Push the left drawer
sides . and right
drawer sides . down
onto the back of the 5
large drawer fronts .
Turn the large locking
cam nuts clockwise
to the “2 o’clock” position
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
11
10
12
Prepare 5 pairs of
drawer sides
a: Insert a large locking
cam nut into the left
drawer sides and the
right drawer sides .
Note: The arrow on the
locking cam nut must
point towards the
hole in the end of the
panel.
b: Push 1 of the quickfit
dowels as far as it will
go into the 5 left drawer
sides and the 5 right
drawer sides .
Note: Only the plastic
thread of the quickfit
dowel sticks out from the
panel.
A
11
12
a:
b:
B
11
12
x 5
B
A
B
x 5 x 5
11 12
BB
x 5 x 5
11 12
AA
11
12
10
Use the Drawer Fittings Bag marked ‘drw kit’ for Steps 1 - 14
hps://www.youtube.com/watch?v=HclfJdkm-Lg
Standard Drawer Box Assembly
B
Turn to “2 o’clock”
Edge Edge Edge

Assembly Instructions
5
Step 3
Fit the large drawer
bases
Slide a large drawer base
. down the grooves in
the drawer sides and
. and down into the
groove in the large
drawer front .
Step 4
Fit the large drawer
backs
Fit a large drawer back
between the drawer
sides and .
Make sure that the large
drawer base fits into
the groove in the large
drawer back .
Hold the large drawer
back in position and
tap the knock-in pegs
through the holes in the
drawer sides and .
16
12
11
10
14
11 12
16
14
14
C
11 12
x 5
Step 5
Fit the handles
Attach 2 handles to
each large drawer front
. using screws .
M
D
10
D
M
D
M
10
10
C
C
12
16
9
12
x 5
x 5
16
11
C
C
14
11
x 5
Fit the drawer braces
Turn the 4 drawer
assemblies over and
hook a drawer brace
onto the bottom edge of
the drawer back .
Fix it to the drawer front
. and drawer back
using 2 screws .
L
E
14
Step 6
Important: Make sure
that the drawer assembly
is square before fitting
the drawer brace.
hps://www.youtube.com/watch?v=HclfJdkm-Lg
Standard Drawer Box Assembly
14
EE
L
L
E
L
E
10
10 14

12 12
Assembly Instructions
6
Step 7
Fit the drawer sides
to the small drawer
fronts
Push the left drawer side
. and right drawer side
. down onto the back
of the small drawer
fronts and .
Turn the large locking
cam nuts clockwise to
the “2 o’clock” position
as far as they will go to
secure the panels.
Important: Make sure
there is no gap between
the fitted panels.
Step 8
8 9
Prepare 2 pairs of
drawer sides
a: Insert a large locking
cam nut into the left
drawer sides and the
right drawer sides .
Note: The arrow on the
locking cam nut must
point towards the
hole in the end of the
panel.
b: Push 1 of the quickfit
dowels as far as it will
go into the left drawer
side and the right
drawer side .
Note: Only the plastic
thread of the quickfit
dowel sticks out from the
panel.
A
11
12
B
11
12
8
B
11
12
9
Note: The small right drawer
front has a small identification
hole (see panels page).
9
a:
b:
B
A
x 2 x 2
11 12
BB
x 2 x 2
11 12
AA
11 11
B
Turn to “2 o’clock”
Edge Edge Edge

8 9
Assembly Instructions
7
Step 9
Fit the small drawer
bases
Slide a small drawer
base down the
grooves in the drawer
sides and and
down into the groove in
the small drawer front
and .
Step 10
Fit the small drawer
backs
Fit a small drawer back
between the drawer
sides and .
Make sure that the small
drawer base fits into
the groove in the small
drawer back .
Hold the small drawer
back in position and
tap the knock-in pegs
through the holes in the
drawer sides and .
15
1211
9
8
13
11 12
15
13
13
C
11 12
x 2
x 2
x 2
D
M
Step 11
Fit the handles
Attach a handle to
each small drawer front
. and using screws
. .
Step 12
M
D
8 9
8 9
12
11
15
C
C
9
12
x 2
15
C
C
13
11
G
G
G
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
G
Important: Make sure
that the drawer assembly
is square before fitting
the wedgefixes.

Assembly Instructions
8
Step 13
Step 14
x 5
Fit runners to the 5
large drawers
Fit the DL runner to
the bottom edge of the
left drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front. Use a bradawl to
mark the fixing
positions, then secure
with 2 screws .
Fit the DR runner to
the bottom edge of the
right drawer side
using the same method.
12
N c
11
F
N d
Fit runners to the 2
small drawers
Fit the DL runner to
the bottom edge of the
left drawer side , as
shown, making sure that
it is pushed up against
the back of the drawer
front. Use a bradawl to
mark the fixing
positions, then secure
with 2 screws .
Fit the DR runner to
the bottom edge of the
right drawer side
using the same method.
12
N c
11
F
N d
12
11
N c
DL
F
F
DL
Runners must be
pushed up against
the drawer front
N d
F
F
DR
x 2
F
F
DL
F
F
12
11
N c
DL
N d
DR
Runners must be
pushed up against
the drawer front
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounted Runners

Assembly Instructions
9
Step 15 Use the Main Fittings Bag for Steps 15 - end
AH
H
A
Finished
front edge
Finished
front edge
Prepare the left side
a: Fit 6 CL runners
to the left side .
The 1st screw uses
the 1st hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
b: Fit a screw into
the hole at the top of the
runner .
c: Insert 2 large locking
cam nuts into the left
side .
Push 2 of the quickfit
dowels as far as they
will go into the left side
. .
Tap 2 wooden dowels
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
N a
1
I
I
F
N a
N a
I
1st
screw
Finished
front edge
CL
Finished
front edge
CL
I
II
N a
F
CL
F
CL
I
II
N a
CL
F
CL
I
II
N a
CL
F
CL
F
CL
CL
CL
CL
B
B
b:
c:
a:
A
1
B
1
H
1
1
10mm
H
A
B
CL
I
II
N a
CL
I
II
N a
CL
I
II
N a
CL
F
CL
F
CL
CL
Finished
front edge
1
1
hps://www.youtube.com/watch?v=Z6lGMy19h7Q
Fixing Bottom Mounted Runners