Argos Kids Sywell 248/6282 User manual

MADE IN
BRITAIN
Dimensions
Width - 99.5cm
Depth - 99cm
Height - 99cm
Kids Sywell - 1 Drawer Bedside
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 2 - 06/02/15
Important - Please read these instructions fully before starting assembly
ALR3018
247/9732
226/1627
227/1356
248/6282
276/2690
275/1096
OLD CODES
Issue 2 - 06/02/15 - Replaced Argos codes with the latest ones.
Update helpline number.
Added note to last step to remove film.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 9.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
12 3
4
Back (X389-359)
(389 x 359mm)
Rail (D2544A)
(363 x 78mm) x 2
5Drawer Front (D2545A)
(359 x 162mm)
9 10
78
6
Left Drawer Side (W370-124LH)
(370 x 124mm)
Right Drawer Side (W370-124RH)
(370 x 124mm)
Drawer Base (T342-367)
(342 x 367mm)
Left Side (D2924A)
(388 x 396mm)
Right Side (D2925A)
(388 x 396mm)
Drawer Back (W331-124)
(331 x 124mm)
Horizontal (D2541A)
(363 x 394mm) x 2

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 14
C
D E F
G H I
J K
9mm Screw (F74) x 2 9mm Screw (F73) x 4
Drawer runner (F1004) x 2
Knock-in Peg (F171GY) x 4
Small locking
nut (F3) x 2
Large locking
nut (F900) x 12
Nail (F51) x 10
Handle (F315) x 1
25mm Screw (F95) x 2
M
Plastic Nail (F91) x 4
L
Wedgefix (F639) x 2
Short cross-head
screwdriver

5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
B
B
E
E
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the small groove is on the inside, as shown.
EE
78
Step 2
Prepare the drawer
front
Screw 2 metal dowels
into the drawer front .
Note: Tighten the metal
dowels up fully against
the panels.
B
5
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
E
7
8
Attach the drawer
sides to the drawer
fronts
Push the left drawer sides
. and right drawer sides
. onto the back of the
drawer fronts .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
7
8
5
E
E
7
8
7
8
B
B
B
5

5
Assembly Instructions
5
Step 4
C
C
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
Step 6
9
7 8
5
6
7 8
9
6
6
C
Attach the handle
Attach the handle to
the drawer front
using screws .
Note: Do not
overtighten the screws.
J
F
5
7 8
Step 7
Fit the wedgefixes
Turn the drawer
assembly over and slide
2 wedgefixes into the
front and back grooves,
as shown, and tighten up
the screws.
L
C
C
L
L
L
9
7
8
6
7
8
9
F
F
J
5

Finished
front edge
1
Finished
front edge
1
Assembly Instructions
6
Step 8
Prepare the left side
a: Place a runner on
the left side . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .
Screw 6 metal dowels
into the left side .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the left side .
K
1
Finished
front edge
H
K
Ha:
a:
b:
b:
B
1
K
H
1
Finished
front edge
H
K
Step 9
Prepare the right side
a: Place a runner on
the right side . Slide
back the top of the
runner and use the 2nd
hole from the front to fit
the 1st screw .
Screw 6 metal dowels
into the right side .
b: Slide the runner
back the other way and
fit the 2nd screw into
the corresponding hole
in the right side .
K
2
H
B
2
K
H
2
H
K
B
B
B
B
B
B
H
Finished
front edge
Finished
front edge
H
K
B
B
B
B
B
B
H
2
2

Finished
front edge
Assembly Instructions
7
Step 10
A
Prepare the 2
horizontals
Tap 2 wooden dowels
into each of the
horizontals .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 4 large locking
nuts into each of the
horizontals .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Fit a horizontal to the
right side
Push a horizontal
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 11
D
D
D
D
D
A
10mm
A
A
3
D
3
3
plain chipboard surface
Finished
front edge
3
2
D
3
D
B
D
x 2
2
Finished
front edge
plain chipboard surface
3

2
Assembly Instructions
8
Step 12
Step 13
Prepare the 2 rails
Tap 2 wooden dowels
into each of the 2 rails .
Insert 2 large locking
nuts into each of the
2 rails .
Step 14
A
4
D
4
x 2
A
A
plain chipboard surface
4
D
D
Fit the other horizontal
to the right side
Push the horizontal
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .
3
2
D
3
2
Finished
front edge
plain chipboard surface
3
Fit the 2 rails
Push the 2 rails onto
the right side .
Use a screwdriver to
tighten the large locking
nut fitted to each of
the 2 rails .
D
4
2
4
4
4
Note: Support this
rail until the left
side has been fitted
in the next step.

Assembly Instructions
9
Step 15
Step 16
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 6 large
locking nuts fitted to
the 2 horizontals and
the 2 rails .
D
1
3
4
2
Fit the back and
plastic nails
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
10
I
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
10
b:
I
10
yy
x
x
3
3
4
4
1