Argos Marcell 4ft6 Frame User manual

Marcell
4ft6 Frame
Dimensions
Width - 146/161
Depth - 210/220
Height - 81
Important – Please read these instructions fully before starting assembly
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Assembly Instructions - Please keep for future reference 1803701
2pt
758/5717
ISSUE1 12/05/11
NOTE: Slats are not supplied

Safety and care advice
Important - Please read these instructions fully before starting assembly
Care and maintenance
• Check you have all the
components and tools listed on
page 2 .
• Remove all fittings from the
plastic bags and separate them into
their groups.
• Keep children and animals away
from the work area, small parts
could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight
on the panels during assembly,
•Assemble the unit as close to its
final position (in the same
room) as possible.
• Assemble on a soft level surface
to avoid damaging the unit or your
floor.
• Parts of the assembly will be
easier with 2 people.
• If using power tools, please
follow the safety instructions
supplied with the tools.
• We do not
recommend the use
of power drill/ drivers
for inserting screws,
as this could damage
the unit. Only use hand
screwdrivers.
•Dispose of all packaging carefully
and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on this
unit.
• This product should not be
discarded with household waste.
Take to your local authority waste
disposal centre.
1
this could cause damage.

Components -Parts
Please check you have all the parts listed below
2
2
Head Board ( 146/161 x 81 cm )
1Foot Board ( 146/161 x 32 cm )
Side Frame x 2 ( 192/202 x 27 cm )
3Center Support ( 201.6/191.6 x 10 cm )
4
Center Leg x 2 ( 27 x 25 cm )
5Supporting Tube x 2 ( 138/153 x 10 cm )
6
( Right & Left )
DRW Front Panel x 2 ( 98 x 16 cm )
7DRW Side Panel x 4( 47 x 10 cm )
8
DRW Back Panel x 2( 90 x 10 cm )
9DRW Lathing x 4 ( 45 x 7 cm )
10
11 DRW Bottom Plateboard x 2
( 91 x 45 cm )
( Right & Left )

3
Ruler - Use this ruler to help correctly identify
t
he screws
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
A
Components - Fittings : If you have damaged or missing components,
call the Customer Helpline:
08456 400800
Please check you have all the fittings listed below
4mm Allen Key x 2 5mm Allen Key x 1
25 mm
6mm Bolt x 8
20 mm 20 mm
8mm Bolt x 4
6mm Bolt x 2
40 mm 30 mm
6mm Bolt x 6 6mm Nut x 6
8mm Bolt x 12
B C
DE F
GH
(Fixed on Headboard & Footboard)
(To fix wooden slats) (To fix wooden slats)
FOR BED
FOR DRAWER
I
40 mm
6mm Bolt x 4
15 mm 50 mm
Cam x 12
Rafix Cam Bolt x 12
J K
I
L
12 mm
Cannect x 4 4mm Allen Key x 1
M
Screw Driver not provided

AssemblyInstructions
Step 1
Attaching Head board
to Side frames
Note: It would be
useful to ask someone
to help you at this stage.
Important: Because
of the size of this unit
we recommend that it is
built in the room
intended for use.
Hang side Frame
onto Head board
Note: Do not tighten
screws until completely
assembled.
1
Note: It would be
useful to ask someone
to help you at this stage.
Attaching Foot board
onto Side frames
Step 2
Step 3
Tighten all ‘ bolts ’
4
Loosen screw ,using
Allen key .
And fasten screw .
A
H
A
Hang side Frame
onto Foot board 2
Loosen screw ,using
Allen key .
And fasten screw .
A
H
A
13
Right
Left
A
H
1
2
3
A
H
3
3

5
Assembly Instructions
Step 5
Note: It would be useful
to ask someone to help
you at this stage.
Use bolt and Allen Key
to fix the Center
Support onto the
Head Board and Foot
Board
Fix the Center Support
Step 4
Fitting the Center Leg
Note: It would be useful
to ask someone to help
you at this stage.
Use Bolts and Allen
Key to fix the Center
Leg onto Center
Support .
D
G
2
B
Note: If the screw hole
can not match when
assemble, need move the
base a little to make sure
the bed is straight.
4
5
G
D
5
4
B
H
4
H
4
1
2
1

6
AssemblyInstructions
Step 7
Note: It would be useful
to ask someone to help
you at this stage.
Use Screw driver , Rafix
Cam Bolt , Cam to
fix the Drawer Side Panel
and Drawer Back
panel .
Note : Screwdriver is
not provided
Fix the DRW Side Panel
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Fix the Supporting Tube
Step 6
Use bolt and Allen
Key to fix the
Supporting Tube to
the Side Frame
C
G
C
G
6
3
3
9
8
8
I
J
6
3
I J
8
9

7
AssemblyInstructions
Step 9
Fix the DRW Bottom
Plateboard
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Fix the DRW Lathing
10
Step 8
Use Bolt and Allen
to fix the DRW Lathing
onto the DRW Back Panel
10
10
9
K
M
L
K M
9
11
Fx the DRW Bottom
Plateboard 11
Note: Screwdriver is not
provided

8
AssemblyInstructions
Step 11
Fix the Drawer
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Fix the DRW Front Panel
Step 10
Use Radfix Cam Bolt
and Cam to fix the
DRW Front Panel
7
I
7
I
J
I
J
7

9
AssemblyInstructions
Put down the slats and
assemble completed
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
F
E