Argos New Penton 246/4943 User manual

New Penton - 2+2 Drawer Chest
246/4943
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400 800
Important –Please read these instructions fully before starting assembly
Dimensions
Width - 80cm
Depth - 40cm
Height - 80cm
Issue 1 - 14/05/14
237/9409
257/2794

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
1
Check you have all the
components and tools listed on
pages 2 and 3.
Remove all fittings from the
plastic bags and separate them
into their groups.
Keep children and animals
away from the work area, small
parts could choke if swallowed.
Make sure you have enough
space to layout the parts before
starting.
Do not stand or put weight on
the product, this could cause
damage.
Assemble the item as close
to its final position (in the same
room) as possible.
Assemble on a soft level
surface to avoid damaging the
unit or your floor.
We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
Parts of the assembly will be
easier with 2 people.
Dispose of all packaging
carefully and responsibly.
This product has been produced
from natural timber; you may
notice some variation in the grain
and colour of different component
parts which is normal for furniture
produced using natural wood and
is not the result of any
manufacturing fault.
The product has been treated
with a wax and oil finish to
prevent dirt ingress and preserve
moisture.
On unpacking the
furniture you may notice an
odour due to this treatment;
this will disappear once the
furniture is unpacked and
assembled after a period of time.
This process may leave some
staining on the packaging
material; please take care to
ensure this does not transfer
to clothing or carpeted surfaces
during assembly.
Care and maintenance
Use an appropriate furniture
polish for natural wood
furniture and a dry cloth to
clean the product.
Avoid placing the furniture in
direct sunlight as this will cause
the timber to prematurely age.
From time to time check
that there are no loose
screws on this unit.
This product should not be
discarded with household
waste. Take to your local
authority waste disposal
centre.

Components - Panels
Please check you have all the panels listed below
2
1Top panel (80 x 40cm)
2Right side panel (78 x 38cm)
3Left side panel (78 x 38cm)
4Right front frame (78 x 9.2cm)
5Left front frame (78 x 9.2cm)
6Back panel x 2 (73 x 37.7cm)
18 H profile (52 x 1.8cm)
12 Block x 4
(10 x 2cm)
top
top
8Smaller drawer front
x 2 (26 x 15.4cm)
7Larger drawer front
x 2 (59 x 15.4cm)
9Larger drawer back
x 2 (56.6 x 15.4cm)
10 Smaller drawer back
x 2 (23.6 x 15.4cm)
11 Drawer side x 8
(29.8 x 15.4cm)
13 Top front frame x 2
(63.6 x 6.5cm)
15 Bottom front frame x 2
(63.6 x 6.5cm)
17 Cross rail (74.4 x 6.5cm)
19 Side drawer runner
x 6 (33.2 x 8cm)
20 Middle drawer
runner (34.4 x 8cm)
16 Back column
(16 x 6.5cm)
21 Larger drawer bottom
x 2 (57.6 x 28.4cm)
22 Smaller drawer bottom
x 2 (24.6 x 28.4cm)
14 Vertical frame
(20 x 6.5cm)

G
3
Components - Fittings
Please check you have all the fittings listed below
If you have damaged or missing components,
call the Customer Helpline: 08456 400 800
Note: The quantities below are the correct amount to complete the assembly. In some cases more
fittings may be supplied than are required.
Ruler - Use this ruler to help correctly identify the screws
0510 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
Tools required
Phillips screwdriver
(small & medium)
Eye protection
(when using a
hammer or glue)
Small
hammer
Ruler/tape
measure
A
D E
C
Wooden dowel x 48
2m
F
H
B
I
JK
14mm Screw x 3 30mm Screw x 32
35mm Screw x 27 22mm Bolt x 12 Metal dowel x 4
Locking
nut x 4
Drawer
handle x 6 Nail x 22
Washer x 2 Wall strap x 1

Assembly Instructions
4
Yes!No!
4
2
a: b: c:
a: b: c:
D
D
Attention: correct
position of panel.
Top
4
2
12
12
Yes!No!
D
D
12
12
3
5
Attention: correct
position of panel.
Top
12
12
5
3
Step 2
Step 1
Fixing right front frame.
(Two people required for
an easier assembly).
a: Insert right side panel
into right front frame
through joints.
c: Fix front frame through
blocks using screws
.
Note:
Before fixing the
blocks into
place it is important to
ensure that the slot and
groove of parts and
are fully pushed together
and lined up correctly at
the top and bottom.
4
4
D
D
b: Place blocks
between the two marks on
the front frame as shown.
First fix to the side panel
using screws .
Fixing left front frame.
(Two people required for
an easier assembly).
a: Insert left side panel
into left front frame
through joints.
c: Fix front frame through
blocks using screws
.
Note:
Before fixing the
blocks into
place it is important to
ensure that the slot and
groove of parts and
are fully pushed together
and lined up correctly at
the top and bottom.
D
D
b: Place blocks
between the two marks on
the front frame as shown.
First fix to the side panel
using screws .
5
5
2
12
2
12
12
3
12
3
12
12

Assembly Instructions
5
Step 3
Step 4
Insert dowels into the
indicated parts.
A
1
Fitting Metal dowels.
Screw metal dowels
into top panel .
Insert metalNote:
dowels as far as
shown.
Do not over tighten.
F
1
F
3
and
19
6x
2
17
16
20
A
A
A
A
A
A
A
A
F
F

Assembly Instructions
6
Step 6
Fit middle drawer runner
to the back column
then fix using screw .
Note:
Note correct
position of dowels before
fixing, as shown.
Step 7
Assembling parts.
Put parts and
together as shown in the
diagram.
16
20
D
A
Note:
Step 5
D
a:
b:
Fixing side drawer
runners.
a: Fit side drawer
runners to the right
side panel. Fit and push
dowels into the front
frame first.
b: Attach side drawer
runners using screw .
Repeat step 5 for the
left side panel and side
drawer runners.
D
D
D
D
19
2
19
19
19
19
13
14
13
13 14
20 16
D

Assembly Instructions
7
Step 8
Assembling the cabinet.
Insert assembled frame
and bottom front frames
into holes on left side
panel , as shown.
15
Step 9
Assembling the cabinet.
Place right side panel
properly ensuring front
frames are all fitted into
their holes at the same
time.
Fix bottom front frame
to the right and left
side panels using screws
as shown in the
diagram.
Step 10
Fixing cross rail.
Fit cross rail to the
side panels and
then fix it using screws
.
Important!
After fixing the
cross rails, with help,
carefully stand the
product upright.
Note: The
hole position.
3
3
15
15
2
B
B
B
B
15
15
B
17
17
3
2
23
D
D
D
D
17

D
Assembly Instructions
8
Step 11
Step 12
Fixing top panel.
With help, fit top panel
to the cabinet.
Insert 4 locking nuts
into side panels where
shown.
Use a screwdriver to turn
locking nuts clockwise
to lock.
Do not over tighten.
Fixing middle drawer
runner.
Fit middle drawer runner
at the vertical frame
then fix it using screw .
Attach back column
to top panel using screw
.
20
D
G
1
G
1
G
16
D
G
G
G
20
D
16
20

Assembly Instructions
9
Step 14
a:
b:
d: Using bolts attach
the drawer handle to
the drawer front.
Repeat step 14 for the
other larger drawer.
Larger drawer
assembly.
a: Attach drawer sides
to the drawer front
using screws .
b: Slide drawer bottom
into slots on drawer
sides and position drawer
back in place.
c: Holding the drawer
back , press the drawer
sides and fix them using
screws .
C
C
E
Step 13
Fixing back panels.
Important:
Cabinet beMUST
‘square’ when back
panels are attached.
a: Attach the right back
panel first using nails
.
18
c: Carefully slot the
second back panel into
the profile and fix it to the
cabinet using nails .
b: Position profile onto
back panel (just attach).
6
I
6
I6
I
18 6
6
6
18
18
I
I
I
C
C
c:
d:
C
C
H
E
H
E
7
21
11
11 9
11
7
9
9
H
21