Argos HOME HM Maine 806/4402 User manual

792/8044
HM Maine Coffee Table
764/8070
Dimensions
Depth - 40cm
Width - 80cm
Height - 45cm
806/4402
798/5362
Important
Version 3 Date: 18/09/17
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
- Please read these instructions fully before starting assembly
797/9323
803/2276
Assembly Instructions - Please keep for future reference

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
that all bolts and fittings are
tightend properly.
Handy Hints

2
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline:
Argos = 0345 6400800
Pilot holes for guidance only
Top support x 2 (76.8 x 6cm)
4
Bottom support x 2 (76.8 x 6cm)
5
Top panel (80 x 40cm)
1
Bottom panel (76.8 x 39.6cm)
2
Side panel x 2 (43.5 x 39.8cm)
3

3
Note: The quantities below are the correct amount to complete the assembly. in some cases mor
may be supplied than are required.
Components - Fittings
ABC
30mm Dowel x 8
15mm Locking nut x 16 39mm Locking pin x 16
D
15mm Screw x 12
E
Plastic support x 6
Ruler - Use this ruler to help correctly identify the screws
Tools required
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
Phillips screwdriver
(medium & large)
Flatblade screwdriver
(medium)
Small
hammer
Ruler/tape
measure
Drill
Eye protection
(when using a
hammer or glue)
7mm Suitable drill bit
(for use with wall plug)
The screws length is measured from the head to the point (30mm screw shown).

Step
Assembly Instructions
Attaching bottom panel
a: Use Screw to fix the
Plastic supports onto
the Bottom support .
1
4
D
E
b: Position the Bottom
supports onto the
Bottom panel use
Screws .
D
b:
E
D
Insert Dowels into the
Bottom panel .
2
B
a:
X 2
5
D
B
D
5
2
5
5
D
5
2
Note: Be sure the edges
of the Plastic supports
even with the edges of
the
Bottom support .
5
E
D
DE
E
D
D
D
D
D
B
B
B
E

Assembly Instructions
5
Step 2
Attaching side panel
Insert Dowels into the
Side panel .
C
Continued on next page.
X 2
A
C
3
3
4
3
Use a screwdriver to turn
Locking nut clockwise
to lock.
4
C
A
A
A
A
B
B
3
CC
4
4
3
a: Screw Locking pins
into the Side panel .
b: Position Top supports
onto the Side panel
.
Insert Locking nut
into the Top supports
.
b:
a:
A
B
Note: Insert locking pins
as far as shown.
Do not over tighten.

c:
d:
Assembly Instructions
Step 2 - continued
6
C
C
2
3
3
C
C
2
3
3
4
4
2
CC
C
C
C
Use a screwdriver to turn
Locking nut clockwise
to lock.
2
C
c: Position Bottom panel
onto the Side panel
.
d: Position Side panel
onto the unit.
Insert Locking nuts
into the Bottom panel .
C
Use a screwdriver to turn
Locking nut clockwise
to lock.
2
4
C
Insert Locking nuts
into the Bottom panel
and Top supports .

7
a:
b:
Assembly Instructions
Step 3
Attaching top panel
A
1
1C
A
A
A
A
A
A
A
A
1
1
3
3
4
4
C
C
C
C
C
C
C
C
a: Screw Locking pins
into the Top panel .
A
Note: Insert locking pins
as far as shown.
Do not over tighten.
b: Position Top panel
onto the unit.
C
Use a screwdriver to turn
Locking nut clockwise
to lock.
3
4
C
Insert Locking nuts into
the Side panels , Top
supports .

8
Assembly Instructions
If you need help or have damaged or missing parts, call the Customer Helpline:
Argos = 0345 6400800
Assembly is complete.
Step 4
Finishing the unit
Note:
It would be useful
to ask someone to help
you at this stage.
With help, place the unit
in the intended position.