Argos Aurora 147/1360 User manual

MADE IN
BRITAIN
Dimensions
Width - 100cm
Depth - 49.5cm
Height - 43.5cm
Aurora - Coffee Table
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 03456 400800
Issue 4 - 26/05/15
Important - Please read these instructions fully before starting assembly
ALR2939
147/1360
166/6553
417/9009
Issue 2 - 05/02/14 - Drawer Base changed to T919-347.
Drawer Back was showing ’x 4’. This has now been amended.
Note added on the last page to remove protective film from panels.
Issue 3 - 13/03/15 - W509LH changed to W350-115LLH and W509RH changed to W350-115LRH.
Issue 4 - 26/05/15 - Added new Argos code to front page - 417/9009

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 26kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: If there is any
chance of this unit being pulled
over by children etc. it is
recommended that the unit is
secured to a wall using suitable
fixings (not supplied).
• Dispose of all packaging
carefully and responsibly.
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.

Components - Panels
Please check you have all the panels listed below
2
1
80%
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Left Side (D2638A)
(420 x 459mm)
Back (D2641A)
(985 x 192mm)
Rail (D2643A)
(959 x 95mm) x 3
32 Right Side (D2639A)
(420 x 459mm)
Horizontal (D2640A)
(959 x 456mm)
Drawer Front (D2642A)
(985 x 192mm)
Top (D2644A)
(999 x 495mm)
Drawer Back (W908-115)
(908 x 115mm)
54
6
8
7
9 10 11
Drawer Base (T919-347)
(919 x 347mm)
Left Drawer Side
(W350-115LLH)
(350 x 115mm)
Right Drawer Side
(W350-115LRH)
(350 x 115mm)

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 10
B
Metal dowel (F901) x 16
C
D
Large locking
nut (F900) x 14
E F
G H I
Small locking
nut (F3) x 2
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J K
Door Plate (F259) x 1
25mm Screw (F50) x 2 13mm Screw (F52) x 8
13mm Screw (F63) x 6
L
N
Door Push (F258) x 1
Feet (F854) x 2
Knock-in Peg (F171) x 4
MR Runner (F160) x 1
b
L Runner (F161) x 1
Mc
L Runner (F159) x 1
Ma
R Runner (F162) x 1
Md
350mm long
Wedgefix (F639) x 6
Mini block (F25) x 4

5
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 03456 400800 quoting the reference
numbers below
Step 1
B
Step 2
Prepare the drawer
front
Screw 2 metal dowels
into the holes shown on
the back of the drawer
front .
Note: Tighten the metal
dowels up fully against
the panels.
B
5
Prepare the drawer
sides
Insert a small locking
nut into the hole
shown on the left drawer
side and right drawer
side .
Note: Arrow on locking
nut must point towards
hole in edge of panel.
Step 3
D
9
10
Attach the drawer
sides to the drawer
front
Push the left drawer side
. and right drawer side
. onto the back of the
drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
10
9
10
5
D
9
10
Groove
DD
B
5
Note: Due to the manufacturing process, the holes for the
locking nut can be on either surface of the drawer sides.
Note: The locking nuts can be on either surface of the drawer sides.
Make sure that the groove is on the inside, as shown.
D
10
9
B
B
B
D
9

C
C
5
5
Assembly Instructions
5
Step 4
Fit the drawer base
Slide the drawer base
down the grooves in the
drawer sides and
and down into the
groove in the drawer
front .
Step 5
Fit the drawer back
Fit the drawer back
between the drawer
sides and .
Make sure that the
drawer base fits into
the groove in the drawer
back .
Hold the drawer back
in position and tap the
knock-in pegs
through the holes in the
drawer sides and .
8
9 10
5
11
9 10
8
11
11
C
9 10
8
8
9
10
11
9
10
8
C
C
N
N
N
N
N
N
N
Step 6
Fit the 6 wedgefixes
Turn the drawer
assembly over.
Slide the wedgefixes
into the small grooves on
the drawer assembly, as
shown.
Once in place, tighten up
the screws.
N

A
M d
R
R
Assembly Instructions
6
Step 7
Fit the runners to the
drawer
Turn the drawer
assembly over.
Fit runner , marked
with ‘R’, to the bottom
edge of the right drawer
side , as shown,
making sure that it is
pushed up against the
back of the drawer front
. . Use a bradawl to
mark the fixing positions,
then secure with 2
screws .
Fit runner , marked
‘L’, to the bottom edge
of the left drawer side
using the same method.
9
M d
10
5
J
M c
Runners must be
pushed up against
the drawer front
J
J
L
M c
L
J
J
9
10
5
Prepare the horizontal
Tap 2 wooden dowels
into the horizontal .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 4 large locking
nuts into the
horizontal .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
A
3
3
E
Step 8
E
E
E
E
A
Finished
front edge
plain chipboard surface
3
E
10mm
A

Finished
front edge
Finished
front edge
A
Assembly Instructions
7
Step 9
A
E
E
B
B
Finished
front edge
a:
b:
c:
2
B
B
B
H
M a
H
H
M a
Finished front edge
J
J
M a
H
Finished front edge
H
1st
screw
2nd
screw
H
3rd
screw
Prepare the left side
a: Tap a wooden dowel
. into the left side .
Screw 5 metal dowels
into the left side .
b: Insert 2 large locking
nuts into the left side
. .
Fit the runner to the
left side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
c: Fit a screw into
the 2nd hole in at the top
of the runner .
Gently tap 2 mini blocks
. into the left side ,
orientated as shown.
H
H
A1
B
1
J
M a
1
Finished
front edge
1
1
1
M a
E
E
B
E
1
B
I
I
I
I1

Assembly Instructions
8
Step 10
a:
b:
c:
Prepare the right side
a: Tap a wooden dowel
. into the right side .
Screw 5 metal dowels
into the right side .
b: Insert 2 large locking
nuts into the right
side .
Fit the runner to the
right side .
The 1st screw uses
the 2nd hole in from the
front of the runner.
The 2nd and 3rd screws
. use the holes that line
up with the other panel
holes.
c: Fit a screw into
the 2nd hole in at the top
of the runner .
Gently tap 2 mini blocks
. into the right side ,
orientated as shown.
H
H
A2
2
E
2
J
M b
2
A
B
B
B
M b
H
Finished front edge
H1st
screw
2nd
screw
H3rd
screw
H
H
M b
H
Finished
front edge
Finished
front edge
M b
Finished front edge
J
J
Finished
front edge
2
2
2
M b
E
E
B
B
B
I
I
I
I2

A
Finished
front edge
Finished
front edge
Assembly Instructions
9
Step 11
Join the right side and
horizontal
Push the horizontal
onto the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the horizontal .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
B
E
3
2
E
E
3
3
2
plain chipboard surface
Step 12
E
E
A
Prepare 1 of the rails
Tap 2 wooden dowels
into a rail .
Insert 2 large locking
nuts into a rail .
A
6
E6
6
x 1
x 2
Step 13
A
E
E
A
6
G
F
Prepare the other 2
rails
Tap 2 wooden dowels
into each rail .
Insert 2 large locking
nuts into each rail .
Screw a foot onto
each rail between the
2 pre-drilled holes using
screws .
A
6
6
E6
G
F
G
F