Argos Alicia 171/5875 User manual

MADE IN
BRITAIN
Dimensions
Width - 82cm
Depth - 49.5cm
Height - 182.5cm
Alicia - 2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 2 - 10/02/14
Important - Please read these instructions fully before starting assembly
ALR2941
171/5875
145/1256
Issue 2 - 10/02/14 - Note added at Step11 to remove protective film.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 44kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
12
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Top (D2667A)
(821 x 495mm)
Left Side (D2668A)
(1808 x 493mm)
7
Right Side (D2669A)
(1808 x 493mm)
Door (D2672A)
(1744 x 389mm) x 2
Back (X1761-813)
(1761 x 813mm)
8
3
Base (D2670A)
(787 x 470mm)
4
Plinth (D2671A)
(787 x 58mm)
5
Hanging Rail (FHR779)
(779mm long)
6

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A B C
D E F
G H
Rule
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J K L
Bracket (F327) x 1
Hinge plate
(F523) x 6 Hinge (F522) x 6
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Step
ladder
Ruler - Use this ruler to help correctly identify the screws
13mm Screw (F79) x 1 13mm Screw (F63) x 14
I
Electric drill
(only use
when drilling
into walls)
F
Large locking
nut (F900) x 6
Wooden dowel (F22) x 6 Metal dowel (F901) x 6
Nail (F51) x 33
Rail holder
(F1014) x 2
25mm Screw (F50) x 4
M
Handle (F319) x 2
40mm Screw (F910) x 4

Finished
front edge
A
K
Prepare the right side
Tap a wooden dowel
into the right side .
Screw 3 metal dowels
into the right side .
Fit 3 hinge plates onto
the right side .
Push a rail holder into
the right side and
secure with screw .
A
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
Prepare the left side
Tap a wooden dowel
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Screw 3 metal dowels
into the left side .
Note: Tighten the metal
dowels up fully against
the panels.
Fit 3 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
Push a rail holder into
the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
B
1
Step 2
K
B
K
1
H
F
1
K
B
BB
K
K
1
Push a rail holder into
the hole shown. Make
sure that it is fitted
straight, in line with the
panel edges and then
secure with screw .
H
F
K
K
K
B
B
B
2
Finished
front edge
10mm
A
A
1
B
2
K
2
H
F
2
A
2
H
F

A
Finished
front edge
Finished
front edge
A
Assembly Instructions
5
Step 3
Step 5
Step 4
C
C
C
C
A
Prepare the base
Tap 2 wooden dowels
into the base .
Insert 4 large locking
nuts into the
base .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
A
4
C
4
C
4
plain
chipboard
surface
Finished
front edge
B
C
Fit the base to the
right side
Push the base onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
4
2
C
C
4
4
2
plain
chipboard
surface
Prepare the plinth
Tap 2 wooden dowels
into the plinth .
Insert 2 large locking
nuts into the
plinth .
A
5
C
5
C
C
A
5
Plain chipboard
surface

Assembly Instructions
6
Step 6
Fit the plinth
Push the plinth onto
the right side .
Use a screwdriver to
tighten the large locking
nut fitted to the plinth
. .
5
2
C
5
Fit the left side
Push the left side
onto the base and
the plinth .
Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the base and the
plinth .
1
4
5
C
4
5
5
2
5
1
4
Step 7
Note: Support the plinth
until the left side has been
fitted in the next step.

G
G
G
G
y
Assembly Instructions
7
Step 8
Step 9
Fit the top
Push the top onto
the assembly and secure
with 4 screws .
y
y
x
x
b:
Fit the back
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back
onto the unit.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
Stand the unit up for
the next step.
8
J
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
8
J
8
Warning: The
unit is heavy.
Lift with care.
3
3
G

Assembly Instructions
Step 10
Step 11
6
H
Fit the hanging rail
Push the hanging rail
into the rail holders
fitted to the side panels.
6
H
6
Prepare the 2 doors
Push fit 3 hinges into
each of the 2 doors .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
F
L
7
90
L
L
F
F
L
F
F
L
F
F
8
7
x 2
Note: Remove the protective film
from the doors before Step 12.

M
Assembly Instructions
9
Step 12
Fit doors and handles
Note: The easiest way to
attach each door is
to fit the top hinge first,
then align and fit the
other hinges.
a: Push the hinge
onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
each door using 2
screws .
L
L
L
K
K
K
L
K
M
D
7
7
a: b:
c: d:
K
L
K
K
B
K
L
L
L
A
L
K
B
e:
D
D
M
7
7