Argos New Sywell 282/4150 User manual

MADE IN
BRITAIN
Dimensions
Width - 70.5cm
Depth - 50cm
Height - 172cm
New Sywell - 2 Door Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 5 - 21/07/14
Important - Please read these instructions fully before starting assembly
ALR3010
282/4150
267/7606
266/2965
281/8960
266/3768
Issue 2 - 07/04/14
Add 4 plastinails
Remove old cat codes and add new
Issue 3 - 28/04/14 - Amended codes
Issue 4 - 02/05/14 - White cat code changed from 248/8242 to 281/8960
Issue 5 - 21/07/14 - Replaced code 274/6977 with 266/3768

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 40.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
1
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Top (D2559A)
(674 x 494mm)
Left Side (D2560A)
(1711 x 496mm)
Base (D2562A)
(674 x 494mm)
Right Side (D2561A)
(1711 x 496mm)
Door (D2563A)
(1650 x 333mm) x 2
Rail (D2597A)
(674 x 125mm)
Back (X1682-700)
(1682 x 700mm)
2
3
4
7
5
Hanging Rail (FHR666)
(666mm long)
6
8

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A B C
D E F
G H
Rule
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
J K L
Bracket (F327) x 1 Hinge plate
(F523) x 6 Hinge (F522) x 6
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Step
ladder
Ruler - Use this ruler to help correctly identify the screws
13mm Screw (F79) x 1 13mm Screw (F63) x 16
I
Electric drill
(only use
when drilling
into walls)
F
Large locking
nut (F900) x 10
Wooden dowel (F22) x 10 Metal dowel (F901) x 10
25mm Screw (F95) x 4
Rail Holder
(F891) x 2
Nail (F51) x 32
M
Handle (F315) x 2
Shelf stud (F110) x 2
N
Plastic Nail (F91) x 4

Finished
front edge
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Prepare the left side
Screw 5 metal dowels
into the left side .
Note: Tighten the metal
dowels up fully against
the panels.
Fit 3 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
To fit the rail holder ,
screw through the top
hole with screw and
into the mark hole drilled
in the left side . Make
sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
B
1
Step 1
Step 2
K
K
K
K
B
B
B
B
B
B
F
I
F
I
F
I
F
1
K
1
I
F
1
F
F
I
F
B
B
B
B
B
K
K
K
K
Finished
front edge
Prepare the right side
Screw 5 metal dowels
into the right side .
Fit 3 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
To fit the rail holder ,
screw through the top
hole with screw and
into the mark hole drilled
in the right side .
Make sure that it is fitted
straight, in line with the
panel edges and then fit
another screw using
the lower hole.
B
2
K
2
I
F
2
F
2

A
Assembly Instructions
5
Step 3
Step 4
C
CC
C
C
A
A
A
10mm
A
Prepare the top
Tap 4 wooden dowels
into the top .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 4 large locking
nuts into the top .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
A
3
3
C3
Finished
front edge
A
C
C
C
C
A
A
A
4
plain
chipboard
surface
Finished
front edge
Prepare the base
Tap 4 wooden dowels
into the base .
Insert 4 large locking
nuts into the base .
A
4
C4

Finished
top edge
Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
6
Step 5
3
4
Fit the top and base
to the right side
Push the top and
base onto the right
side .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the top and base.
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
3
4
2
3 4
C
C
B
C
Step 6
plain
chipboard
surface
C
C
A
A
Prepare the rail
Tap 2 wooden dowels
into the rail .
Insert 2 large locking
nuts into the rail .
Step 7
A
5
C5
2
5
Plain chipboard
surface
Fit the rail
Push the rail onto the
right side .
Use a screwdriver to
tighten the large locking
nut fitted to the rail .
5
2
C5
2
Finished
top edge
5
Note: Support the
rail until the left
side has been fitted
in the next step.

Finished
front edge
Assembly Instructions
7
Step 8
Step 9
Fit the left side
Push the left side
onto the assembly.
Use a screwdriver to
tighten the 5 large
locking nuts fitted to
the top , base and
rail .
1
C
3 4
5
5
1
3
4
b:
Fit the back and
plastic nails
a: Square up the unit by
making sure that
measurement x to x
equals y to y.
b: Place the back ,
coloured surface facing
down, onto the unit as
shown.
Nail around the
outside edges of the
back .
Note: Nails should be
spaced about 150mm
apart.
8
H
The measurement from top corner X to bottom corner X must be
equal to the measurement from top corner Y to bottom corner Y
a:
8
y
y
x
H
Warning: The
unit is heavy.
Lift with care.
8
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
N
1
2
N
Stand the unit up
for the next stage.
1
2
N
x
N
N

Fit the hanging rail
and shelf studs
Push the hanging rail
into the rail holders
fitted to the side panels.
Push the 2 shelf studs
up into the holes in the
top to act as door
buffers.
Assembly Instructions
8
Step 10
Step 11
6
I
6
6
I
Prepare the 2 doors
Push fit 3 hinges into
each of the 2 doors .
Secure each hinge with
2 screws .
Note: Before securing
with the screws, make
sure that the hinges are
positioned at 90 degrees
with the edge of the
door.
F
L
7
90
L
L
F
F
L
F
F
L
F
F
7
x 2
G
3
3
GG

Assembly Instructions
9
Step 12
Fit doors and handles
Note: The easiest way to
attach each door is
to fit the top hinge first,
then align and fit the
other hinges.
a: Push the hinge
onto the front part of the
hinge plate .
The recess at the bottom
of screw B goes into the
slot in the hinge plate.
b: Keep the hinge
FLAT against the hinge
plate as you slide it
across as far as it will go.
Tighten screw A.
c: The hinge must be
flat against the hinge
plate prior to any
adjustment.
d: The hinge must
NOT be AT AN ANGLE
to the hinge plate
when assembled.
This would indicate that
the recess at the bottom
of screw B had not
located in the slot in the
hinge plate and the hinge
would not be secure.
Remove the hinge from
the hinge plate and then
re-assemble being
careful to follow
instructions a-c.
e: Attach a handle to
each door using 2
screws .
L
L
L
K
K
K
L
K
M
D
7
7
a: b:
c: d:
K
L
K
K
B
K
L
L
L
A
L
K
B
e:
M
D
7
7
MD