Argos Anderson 2 Door Tall Robe 274/3750 User manual

MADE IN
BRITAIN
Dimensions
Width - 100cm
Depth - 50cm
Height - 200cm
Anderson - 2 Door Tall Robe
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 3 - 03/04/14
Important - Please read these instructions fully before starting assembly
ALR3004
274/3750
258/2588
268/9986
Issue 2 - 18/07/13 - Drillings on Side panels have altered.
The Top Hanging Rail, both Shelf positions and the Back Rail have all moved.
The Left Side in now D2048B and the Right Side is now D2049B.
Issue 3 - 03/04/14 -
Add 4 plastinails.
Remove old cat codes and add new ones.

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 60kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Note: If required the next page
can be cut out and used as
reference throughout the
assembly. Keep this page with
these instructions for future
reference.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that this unit is
secured to a wall using the
bracket supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
1
80% x 2
90% x 1
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Back Rail (D2053A)
(965 x 120mm)
Door (D2056A)
(1894 x 494mm) x 2
Top (D2057A)
(999 x 496mm)
Base (D2058A)
(965 x 470mm)
Plinth (D2059A)
(965 x 80mm)
2
3
4
9 10
5
6
7
Hanging Rail (FHR945)
(945mm long) x 2
8
Large Shelf (D2052A)
(965 x 467mm)
Left Side (D2048B)
(1978 x 471mm)
Right Side (D2049B)
(1978 x 471mm)
Back (X956)
(1914 x 988mm)

Please check you have all the fittings listed below
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 8
B
Metal dowel (F901) x 12
C
G H
J K
Hinge (F518) x 8
F
13mm Screw (F63) x 20
I
E
13mm Screw (F79) x 1
D
Nail (F51) x 40
Large locking
nut (F900) x 12
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Tools required
Rule
ScissorsSquare
Spirit
level
Hammer Bradawl
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
Step
ladder
Ruler - Use this ruler to help correctly identify the screws
Electric drill
(only use
when drilling
into walls)
mm 10 20 30 40 50 60 70 80 90 100 mm 10 20 30 40 50 60 70 80 90 100
Shelf stud (F110) x 4 Rail holder
(F1014) x 4
19mm Screw (F461) x 4
Hinge plate (F523) x 8
L
Bracket (F327) x 1
M
Handle (F266) x 2
N
Plastic Nail (F91) x 4

Finished
front edge
A
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
80% x 3
10mm
A
Prepare the left side
Screw 4 metal dowels
into the left side .
Note: Tighten metal
dowels up fully against
the panel.
Fit 4 hinge plates onto
the left side , making
sure that the slot is
facing towards the
finished front edge.
Insert 2 large locking
nuts into the left side
. .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Tap a wooden dowel
into the left side .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
B
1
J
1
C
A
1
1
B
C
J
B
B
B
C
C
BJ
J
J
J
1

Assembly Instructions
5
Step 2
Prepare the right side
Screw 4 metal dowels
into the right side .
Insert 2 large locking
nuts into the right
side .
Fit 4 hinge plates onto
the right side , making
sure that the slot is
facing towards the
finished front edge.
Tap a wooden dowel
into the right side .
B
2
J
2
C
A
2
2
B
C
BB
B
C
Finished
front edge
J
2
J
J
J
J
A
A
Prepare the base
Insert 4 large locking
nuts into the base .
Tap 2 wooden dowels
into the base .
CC
C
C
C
Finished
front edge
plain chipboard surface
4
A
4
A
4
Step 3

Finished
front edge
A
Assembly Instructions
6
Step 4
Step 5
A
C
plain chipboard surface
7
Prepare the plinth
Insert 2 large locking
nuts into the plinth .
Tap 2 wooden dowels
into the plinth .
C7
A
7
Finished
front edge
Fit the base to the
right side
Push the base onto
the right side .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the base .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
4
plain chipboard surface
B
C
2
4
2
4
C
C
C
Note: The plinth is narrower than the back rail
(please refer to the panels page).

Finished
front edge
A
Assembly Instructions
7
Step 6
Fit the plinth
Push the plinth onto
the right side .
Use a screwdriver to
tighten the large locking
nut fitted to the plinth
. .
7
2
7
C
Step 7
Prepare the back rail
Insert 2 large locking
nuts into the back rail
. .
Tap 2 wooden dowels
into the back rail .
C
6
A
6
C
C
A
plain chipboard surface
6
plain chipboard surface
7
2

Finished
front edge
Finished
front edge
Finished
front edge
Assembly Instructions
8
Step 8
Fit the back rail to the
left side
Push the back rail
onto the left side .
Use a screwdriver to
tighten the large locking
nut fitted to the back
rail .
6
1
6
C
1
plain chipboard surface
6
1
7
2
6
1
Step 9
Fit the left side
Push the left side
onto the base and
plinth , then push the
back rail onto the
right side .
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the back rail , base ,
and plinth .
1
4
7
6
2
C
6 4
7
4

Assembly Instructions
9
Step 10
Prepare the top
Screw 4 metal dowels
into the top .
Step 11
Fit the top and plastic
nails
Push the top onto
the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left side and right
side .
B
B
B
B
B
3
3
1
2
C
3
Rounded
front edge
2
1
Rounded
front edge
3
Tap 2 plastic nails
into the bottom edge of
each of the sides and
. .
N
1
2
N
N
N
N