Argos Toronto 697/0804 User manual

Toronto Single
Important - Please read these instructions fully before starting assembly
If you need help or have damaged or
missing parts, call our Customer Helpline: 01242 621266
Assembly Instructions - Pleasekeep for future reference 697/0804
697/0770
697/0835
Dimensions
Width - 96cm
length - 190cm
Height - 85cm Issue 2 - 31/01/2014
697/0749

Safety and Care Advice
Important–Please read these instructionsfully before starting assembly
• Check you have all the
componentsand tools listed
on pages 2 and 3.
• Remove all ?ttings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight
on the product,this could
cause damage.
• Assemble the item as close
to its ?nal position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging
the unit or your ?oor.
• Parts of the assembly will
be easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do not use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screw son
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Care and maintenance
•Skin contact: Remove
contamination by washing with
soap and water.This procedure
should also be followed prior to
eating and drinking.
•Eye contact: Rinse immediately
with clean water for 15minutes
and seek medical advice.
•If swallowed: Seek medical
advice immediately.
Glue safety - Take care when using glue, please follow the advice below
1
Note: This assembly
instruction covers a number of
different sizes of bed.
Although your bed may
appear different to the model
shown the assembly
procedure remains identical.
the unit or your ?oor.

Please check you have all the ?ttings listed below
Tools required
A
35mm CS Screw x8
BC
Note:The quantities below are the correct amount to complete the assembly. In some cases more
?ttings may be supplied than are required.
D
Components-Fittings
Cross Headed Screwdriver Small
hammer
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150
0 1 2 3 4 5 6
2
Ruler - Use this ruler to help correctly identify the fixings
05 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 105 110 115 120 125 130 135 140 145 150 155 160 165 170
GH
12mm CAM Lock
x 10 I
15ml Glue Tube
x1
J
M
CAM Peg x 10
E
K
F
L
O
60mm Allen Bolt x 8 25mm Allen Screw x 4
4mm x 25mm Screw x 2 15mm Round Head screw X 18
Castor
x 5
Silver Handle
x 2 Washer
x 12
Allen Key
x1
M6 Cross dowel x 8
Allen Key
(Supplied)
Flat Headed Screwdriver
missing parts, call our Customer Helpline: 01242 621266
If you have any damaged or
Wooden dowel x 8
N

Components-Panels
Please check you have all the panels listed below
2
1
1
3
4
5
6
1
2
3
4
5
6
Bed Panels
Side Rails x 2 (190 x 18cm)
Toe End Panel x 1(96 x 35cm)
Head End Panel x 1 (96 x 49cm)
Headboard Struts x 2
Headboard Rails x 2 (96 x 17cm)
Roll of Slats x 1
12
8
8
7
7
11
9
9
10
5
4
7
8
9
10
11
Underbed drawer Panels
3
12
Drawer Base x 2 (90 x 40cm)
Drawer Side x 2 (39 x 12cm)
Support Rails x 2 (39 x 6cm)
Centre Support x 1 (39 x 6cm)
Drawer Back x 1 (182 x 12cm)
Drawer Front x 1 (188 x 12cm)

A
4
Assembly Instructions
Step 1
Step 2
H
A
H
A
x 4
A
A
A
A
A
A
A
A
x 4
H
H
H
H
H
H
Note the correct
alignment of the
Cross Dowel slots
Fitting the side rails
to the head end panel
13
1
3
1
Position the side rails
as shown and fit 2 x M6
Cross dowels in to
the side rails. Note that
the slot must be aligned
as shown in the diagram.
Next fit the M6 x 60 bolts
through the head end
and in to the ends of the
side rails. Use the 4mm
Allen key to tighten the
bolts in to the cross
dowels.
H
Fitting the side rails
to the toe end panel 1
2
Position the side rails
as shown and fit 2 x M6
Cross dowels in to
the side rails. Note that
the slot must be aligned
as shown in the diagram.
Next fit the M6 x 60 bolts
through the toe end
and in to the ends of the
side rails. Use the 4mm
Allen key to tighten the
bolts in to the cross
dowels.
H
2
x 4 x 4
x 4 x 4
H
H
Note the correct
alignment of the
Cross Dowel slots
H
H
H
H
H
H
H
H

5
Assembly Instructions
Step 3
E
x 8
5
5
4
4
E
E
E
E
Pilot Holes
Pilot Holes
C
K
C
K
CK
x 12
Fitting the headboard
assembly to the head
end panel 3
Fix the assembled
headboard on to the
back of the head end
panel using 4 x 25mm
Allen screws and
12 x washers
Note that there are 6
holes in the head end
panel. Please use the
top 4 holes to fit the
struts as shown in the
detail view.
Fitting the headboard
struts to the head
board rails
45
Position the headboard
rails and headboard
struts as shown.
Fix the struts to the rails
using 8 x 15mm round
head screws
Note that the pilot holes
on the headboard rails
are offset - see diagram
below.
E
x 4
Use top holes
CK
Detail View
Step 4
a
a
b
b
Note offset
pilot holes
in the
headboard
rails
C
K

6
Assembly Instructions
Step 5
x 8
B
B
B
B
B
B
B
B
B
6
Push Push
Glue the dowels
in place
N
L
9
9
10
N
N
N
N
L
L
L
L
x 8
N
Step 6
Fitting the roll of slats
to the side rails.
Open the roll of slats
and lay them on the
side rails as shown.
Pull the end slats out
so that they touch the
head end panel and
the toe end panel.
Secure each corner
using 4 x 35mm screw
The side rails may be
slightly bowed out. If so
push them in on both
sides before fitting the
last 4 x 35mm screw
6
Fitting the wooden
dowels to the
support rails and the
CAM Lock to the
Centre Support Rail
as shown.
Put a small amount of
glue in to the holes and
gently tap the wooden
dowels in to the support
rails as shown.
Wipe off any excess
glue with a damp cloth
9
N
G
G
x 2
G
G10

7
Assembly Instructions
Step 7
E
x 10
I
x 5
I
I
I
I
I
910
9
E
E
E
E
E
E
The cam fixing pegs should be
screwed down to this shoulder
F
11
12
F
F
F
F
F
Step 8
x 10
F
Position the support
rails and the
castors as shown.
Using the round head
screws fix the
castors to the
support rails as
shown.
I9
I
I
9
9
E
Fitting the castors
to the support rails
and
F
11
Fitting the cam pegs
as shown. Attach the
11
drawer back and
to the drawer back
Position the drawer
cam pegs to the
front and back
11
12
12
drawer front
F
and front.
12
10
F
F

8
Assembly Instructions
G
G
8
8
12
9
10
9
G
L
L
L
Glue the dowels
in place
N
L
L
Glue the dowels
in place
G
N
8
1
L
L
7
CAM FIXING STEPS
11
2
L
3
L
7
8
G
4
Fitting the drawer
bases and the
drawer back
Position the drawers
as shown. Put a small
amount of glue into the
holes and gently tap the
drawer back to the
support rails as shown.
Wipe off any excess of
glue with damp cloth.
Attach the cam lock
fix the drawer back
to the drawer sides.
G
x 4
11
11
11
8
G
Step 9
Step 10
Position the drawer
sides and the
support rails and
as shown. Put a small
amount of glue into
the holes and gently
tap the support rails
into the drawer front
as shown.
Wipe off any excess
gluewithdampcloth.
Attach the cam lock
fix the drawer sides
to the drawer front
as shown.
G
G
12
89
9
9
8
Do not assemble the
drawers if the dowels
are not glued.
Fitting the support
rails and drawer
sides to the drawer
front
x 4
8
12
12
7
Slide the drawer bases
in to the drawer sides
and drawer front 8
12
Note use plenty of glue
Centre Support Rail 10
12

9
Assembly Instructions
J
J
D
x 2 x 2
D
D
J
J
12
If you need help or have damaged or
missing parts, call our Customer Helpline: 01242 621928
Finally push the drawer
unit under the bed frame.
The bed is now complete.
Step 12
Step 11
Fitting the handles
to the drawer front 12
Position the drawer as
shown. Use 2 x screw
to fix the silver
handle to the drawer
front as shown.
J
D