Argos Newport Chest Pack User manual

MADE IN
BRITAIN
Newport - Chest Pack
Assembly Instructions - Please keep for future reference
If you need help or have damaged or missing parts, call the Customer Helpline: 08456 400800
Issue 1 - 22/05/14
Important - Please read these instructions fully before starting assembly
ALR3053
245/8409
249/3842
2 Drawer Chest
Dimensions
Width - 65.5cm
Depth - 35.5cm
Height - 57.5cm
Bedside Chest
Dimensions
Width - 35.5cm
Depth - 35.5cm
Height - 41cm

Safety and Care Advice
Important - Please read these instructions fully before starting assembly
• Warning: This unit weighs
approximately 22.5kgs.
Please lift with care.
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Parts of the assembly will be
easier with 2 people.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close to
its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor (use opened
out unit carton).
1
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household
waste. Take to your local
authority waste disposal centre.
Components - Panels
Please check you have all the panels listed below
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
3Small Drawer
Front (DF276)
(315 x 162mm)
1Left Drawer
Side (W320-124LH)
(320 x 124mm) x 3
Right Drawer
Side (W320-124RH)
(320 x 124mm) x 3
2
6
Small Drawer
Base (T297-317)
(297 x 317mm)
7 8
Drawer Panels
Large Drawer
Back (W586-124)
(586 x 124mm) x 2
Large Drawer
Base (T597-317)
(597 x 317mm) x 2
Large Drawer
Front (DF282)
(615 x 162mm) x 2
4
5Small Drawer
Back (W286-124)
(286 x 124mm)
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could damage the unit.
Only use hand screwdrivers.
• Safety note: It is
recommended that the 2
Drawer Chest is secured to a
wall using the bracket supplied.
• Dispose of all packaging
carefully and responsibly.

Components - Panels
Please check you have all the panels listed below
2
9 10 11
80%
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
13
Left End (DF272)
(395 x 351mm)
Plinth (DF278)
(319 x 65mm)
Right End (DF273)
(395 x 351mm)
Top (DF274)
(355 x 352mm)
Fixed Shelf (DF275)
(319 x 325mm)
12
Back (X345-182)
(345 x 182mm)
Left End (DF420)
(560 x 351mm)
Right End (DF421)
(560 x 351mm)
Top (DF281)
(655 x 352mm)
Plinth (DF284)
(619 x 65mm) x 2
Fixed Shelf (DF422)
(619 x 325mm)
14
Bedside Chest Panels
2 Drawer Chest Panels
15 16
17
19
20
18
Back (X645-532)
(645 x 532mm)

Please check you have all the fittings listed below
Tools required
3
Components - Fittings If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Note: The quantities below are the correct amount to complete the assembly. In some cases
more fittings may be supplied than are required.
A
Wooden dowel (F22) x 6
B
Metal dowel (F901) x 28
C
D E
Large locking
nut (F900) x 22
F
G H I
Small locking
nut (F3) x 6
Ruler - Use this ruler to help correctly identify the screws
mm 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170
25mm Screw (F50) x 10
KR (F601)
L (F600)
F599
F599
Drawer stops (F599) x 6
Runners (F600) x 3 and (F601) x 3
Nail (F51) x 22 Knock-in Peg (F171GY) x 12
Plastic Nail (F91) x 8
Rule Scissors Hammer
Eye protection
(when using a
hammer or drill)
Cross-head
screwdriver
Electric drill
(do not use for
fitting screws)
J
Wedgefix (F639) x 10
Handle (F314) x 5

3
Assembly Instructions
4
If you have damaged or missing components, call the
Customer Helpline: 08456 400800 quoting the reference
numbers below
Step 1
B
B
B
C
C
CC
12
Step 2
Prepare the small
drawer front
Screw 2 metal dowels
into the small drawer
front .
Note: Tighten the metal
dowels up fully against
the panels.
B
3
Prepare 1 pair of
drawer sides
Insert a small locking
nut into the hole
shown on the left drawer
side and the right
drawer side .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
Step 3
C
1
2
Attach the drawer
sides to the small
drawer front
Push the left drawer sides
. and right drawer sides
. onto the back of the
small drawer front .
Turn the small locking
nuts on the left
drawer side and right
drawer side .
Note: Turn the locking
nuts clockwise to
secure panels - more
than 1/2 a turn.
1
2
3
C
C
1
2
1
2
B
B
3
Steps 1-20 will show you how
to build the Bedside Chest

Assembly Instructions
5
Step 4
I
I
Fit the small drawer
base
Slide the small drawer
base down the
grooves in the drawer
sides and and
down into the groove in
the small drawer front .
Step 5
Fit the small drawer
back
Fit the small drawer back
. between the drawer
sides and .
Make sure that the small
drawer base fits into
the groove in the small
drawer back .
Hold the small drawer
back in position and
tap the knock-in pegs
through the holes in the
drawer sides and .
1
7
2
3
5
1 2
7
5
5
I
1 2
Step 6
I
I
7
1
5
2
1
7
2
SNAP!
SNAP!
F599
K
K
F599
K
F599
K
F599
K
Push in drawer stops
Carefully break off 2
drawer stops (F599) from
a pair of the drawer
runners .
Push the drawer stops
fully through the drawer
sides and from
the inside.
K
1 2 1
2

Assembly Instructions
6
Step 7
Attach the handle
Attach a handle to the
small drawer front
using screw .
Note: Do not
overtighten the screws.
F
E
3
Step 8
Fit the wedgefixes
Turn the drawer
assemblies over and
slide 2 wedgefixes
into the front and back
grooves, as shown, and
tighten up the screws.
Step 9
J
J
J
J
E
E
F
3
Finished
front edge
R
F601
K
Prepare the right end
Separate the runners .
Push fit a right runner
marked ‘R’ into the holes
shown on the right end
. .
Note: Runners must be
be fitted flat against the
panel. If necessary
gently tap into final
position.
Screw 3 metal dowels
into the right end .
Insert 2 large locking
nuts into the right
end .
Note: The arrow on the
locking nut must point
towards the hole in the
edge of the panel.
K
K
10
B
K
B
B
D
D
D
B
10
10
D
10

A
Finished
front edge
Finished
front edge
Assembly Instructions
7
Step 10
Prepare the fixed
shelf
Insert 4 large locking
nuts into the
fixed shelf .
Step 11
D
D
D
D
D
12
12
Finished
front edge
Fit the fixed shelf to
the right end
Push the fixed shelf
onto the right end .
Use a screwdriver to
tighten the 2 large
locking nuts fitted to
the fixed shelf .
Note: Turn the large
locking nuts as far as
they will go - more than
1/2 a turn.
Step 12
10
12
D
D
12
12
10
B
D
D
D
A
Prepare the plinth
Tap 2 wooden dowels
into the plinth .
Note: Wooden dowels
must not stick out from
the edge by more than
10mm or they may
damage other panels.
Insert 2 large locking
nuts into the plinth .
D13
10mm
A
A
13
13

Finished
front edge
Assembly Instructions
8
Step 13
Step 14
Prepare the left end
Push fit a left runner
marked ‘L’ into the holes
shown on the left end
. .
Screw 3 metal dowels
into the left end .
Insert 2 large locking
nuts into the left end
. .
Step 15
Fit the plinth
Push the plinth onto
the right end .
Use a screwdriver to
tighten the large locking
nut fitted to the plinth
. .
10
13
D
13
10
13
B
B
D
D
K
L
F600
K
K
9
B
9
9
D
9
Fit the left end
Push the left end
onto the assembly.
Use a screwdriver to
tighten the 3 large
locking nuts fitted to
the fixed shelf and
the plinth .
9
D
12
13
9
12
13
Finished
front edge
B

Assembly Instructions
9
Step 16
Step 17
Prepare the top
Screw 2 metal dowels
into the top .
B
11
B
B
B
B
11
Finished
front edge
Fit the top
Push the top onto
the assembly.
Use a screwdriver to
tighten the 4 large
locking nuts fitted to
the left end and right
end .
Step 18
11
D
9
10
11
9
10
Fit the 4 plastic nails
Tap 2 plastic nails
into the bottom edge of
each of the ends and
. .
H
9
10
H
H
H
H
9
10