Argos White Toddler bed 4277891 User manual

White Toddler bed - 140x70cm
Dimensions
Length - 144cm
Depth - 75cm
Height - 57cm
Weight - 13kg
Issue 1 - 11/05/15
Important – Please read these instructions fully before starting assembly
Assembly Instructions - Please keep for future reference 4277891
If you need help or have damaged or missing parts, call the Customer Helpline:
0045 7668 8055 or e-mail: order@flexa.dk

1
Safety and Care Advice
Important – Please read these instructions fully before starting assembly
80-12801-20 Toddler bed
IMPORTANT! KEEP FOR FUTURE REFERENCE
PLEASE DISPOSE OF PACKAGING MATERIAL.
PLASTIC BAGS CAN BE DANGEROUS TO YOUNG CHILDREN
WARNING! This bed is suitable for a child from 18 months to 4 years.
WARNING! Do not place this child’s bed near heat sources, windows and other furniture.
WARNING! Do not use this child’s bed if any of the parts are broken, torn or missing.
WARNING! Once assembled, this bed must not be disassembled. Screws must not be removed once inserted.
This child’s bed is to be used with a 1400mm x 700mm maƩress.
All assembly Įxings should be checked periodically and re-Ɵghtened where necessary.
Children are likely to play, bounce, jump and climb on beds, therefore the child’s bed should not
be placed too close to other furniture or windows, blind cords, curtain pulls or other strings or cords, and should be
placed either Ɵght to any wall or have a gap of 300mm between the wall and the side of the bed.
Any addiƟonal or replacement parts should only be obtained from the manufacturer or distributor.
This product complies to standard BS8509: 2008+A1:2011
CARE AND MAINTENANCE
To clean use a damp cloth, avoiding the use of strong detergents or abrasives.

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
pages 2 and 3.
• Remove all fittings from the
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
• Do not stand or put weight on
the product, this could cause
damage.
• Assemble the item as close
to its final position (in the same
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
unit or your floor.
• Parts of the assembly will be
easier with 2 people.
• We do not
recommend the
use of power
drill/drivers for
inserting screws,
as this could
damage the unit. Only use hand
screwdrivers.
• Dispose of all packaging
carefully and responsibly.
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Care and maintenance
Glue safety -Take care when using glue, please follow the advice below
Eye contact: Rinse immediately
with clean water for 15 minutes
and seek medical advice.
If swallowed: Seek medical
advice immediately.
Skin contact: Remove
contamination by washing with
soap and water. This procedure
should also be followed prior to
eating and drinking.
2

Bedside left x1
(140x8.9x2.0cm)
8
Bedside right x1
(140x8.9x2.0cm)
7
List x2
(138x2.0x2.0cm)
9
Top rail x2
(75x6.5x2.0cm)
3
End rail x3
(62x8.9x2.0cm)
4
Leg short x2
(34.7x6.5x2.0cm)
1Leg long x2
(49.9x6.5x2.0cm)
2
Slat x12
(69.7x6.5x1.5cm)
6
Safety rail x2
(100x8.9x2.0cm)
5
Distance piece x2
(6.3x6.5x2.0cm)
10
Components - Parts
Please check you have all the parts listed below
No. 12-02014002-20No. 12-02014001-20
No. 12-02013801
No. 12-02007502-20
No. 12-02006201-20
No. 12-02003472-20 No. 12-02004991-20
No. 12-01506971No. 12-02010001-20
No. 12-02000631-20
If you have damaged or missing components,
call the Customer Helpline:
0045 7668 8055
3

Please check you have all the fittings listed below
4,0x30mm Chipboard screw x24
Tools required
A
Note: The quantities below are the correct amount to complete the assembly. In some cases more fittings
may be supplied than are required.
4,0x35mm Chipboard screw x16
B
E
6,3x105mm Assembly screw x6
C
10x45mm Dowel x12
D
Components - Fittings
Phillips
screwdriver
(medium)
Small
hammer
Allen key
4mm incl.
Flatblade
screwdriver
(medium)
8x50mm Dowel x16
Ruler/tape
measure
Eye protection
(when using a
hammer or glue)
7,0x60mm Confirmat screw x12
FNo. 3908-70060
Glue tube 15 gram x2
GNo. 4022-012
4
No. 3909-631051
No. 3930-10045
No. 3903-40035
No. 3901-40030
No. 4033-004
No. 3930-08050

Assembly Instructions
Step 1
Place distance pieces
10 and legs 1and 2
so that the top holes are
facing upwards.
Apply glue Ginto the
holes of distance pieces
10 and legs 1and 2.
DO NOTAPPLY TOO
MUCH GLUE G.
Attach dowels Eto the
distance pieces 10 .
Attach dowels Eto the
legs 1and 2.
Turn the distance pieces
10 180º around, so that
the attached dowels E
are facing downwards.
Apply glue Ginto the
holes of distance pieces
10 .
Attach dowels Eto the
distance pieces 10 .
Attach dowels Dto the
end rails 4.
It may be necessary
to tap the dowels in
very gently with a small
hammer.
Attach end rails 4to
the legs 1and 2with
screws Cusing the allen
key.
4
1 2
4
4
4
1
1
2
2
Step 2
E E
G
G
G
C
C
C
C
C
E
E
E
D
D
D
x3
x2 x2
5
10 10
x2 x2

Assembly Instructions
Step 3
Place list so that holes
are facing vertical and
chamfer is positioned
downwards.
Apply glue Gto the
upper side of the list 9.
Attach list 9to the
bedside 7and 8with
screws Bso that the
chamfer is facing outside.
Attach bedsides 7and
8to the legs 1and 2
with screws Fusing the
allen key.
Step 4
8
9
9
9
9
8
1
1
2
2
1
7
7
7
B
B
F
F
F
F
F
F
B
B
B
B
B
7and 8
Chamfer
Chamfer
Gx2
6

Assembly Instructions
a:Apply glue Ginto the
holes of top rails 3.
DO NOTAPPLY TOO
MUCH GLUE G.
b: Place top rails 3
carefully on top of the
legs 1and 2so that
dowels Ego into the
holes of top rails 5.
a:Apply glue Ginto the
holes of safety rails 5.
Apply glue Ginto the
holes on the top side of
bedsides 7and 8.
DO NOTAPPLY TOO
MUCH GLUE G.
b: Place distance pieces
10 with dowels Einto
the holes on top side of
the bedsides 7and 8.
Place safety rails 5
carefully on top of the
distance pieces 10 so
that dowels Ego into the
holes of safety rails 5.
c:Attach safety rails
5to the legs 2with
screws F
Step 5
Step 6
b:
b:
b:
a:
a:
b:
c:
F
F
G
G
G
F
8
1
1
2
2
5
10
10
5
2
2
3
3
7
G
7
3
5
x2
x2

Assembly Instructions
Place one slat 6in the
centre of the bed. Follow
the measurement .
Place two slats 6in the
ends of the bed. Follow
the measurement .
Push the bedsides 7
and 8together whilst
attaching middle slat
6to the bed with two
chipboard screws A.
Position the remaining
nine slats 6in the bed
with a distance of 54 mm
between each.
Fasten each slat with two
screws A
Assembly for this
furniture is complete.
Step 7
Step 8
608 mm
13 mm
54 mm
6
6 6 6 6 6 6 6 6 6
6
8
7
6
A
A
A
A
A
A
A
A
A
8
Ref.no. 44-01509-20 B Stand: 110515 Page 9 (80-12801-20)
If you need help or have damaged or missing parts, call the Customer Helpline: 0045 7668 8055
E-mail: order@flexa.dk