Aritech 1X-F Series User manual

P/N 501-415003-4-20 • REV 2.0 • ISS 06JUL11 1
1X-F Series Quick Installation Guide
Figure 1: Zone and device connections
Overview
This document provides quick installation information for
your product. For detailed installation information,
including EN 54-13, intrinsically safe, and BS 5839-1
operating mode requirements, see the installation
manual.
Zones and zone devices
Connect zone wires and devices as shown in Figure 1.
Line resistance
Mixed zones 40 Ωmax.
Automatic / manual zones 55 Ωmax.
Detectors and manual call points per zone
Dx700 series detectors 20 max.
Other detectors 32 max. [1]
Manual call points 32 max.
[1] Or as defined by local codes and standards
Manual call point resistance [1]
Mixed zone 100 Ω
Manual zone 100 to 680 Ω
[1] Resistance must be rated at 1 W min.
Inputs and outputs
The function of inputs and outputs is defined by the
operating mode.
Inputs
EN 54-2 Remote reset Delays off
EN 54-2 Evacuation Remote reset Delays off
EN 54-2 Scandinavia Fire routing / extended fire
routing delay [1]
Delays off
BS 5839-1 Class change Delays off
NBN S21-100 Remote reset Delays off
NEN 2535 Fire routing inhibit delay Delays off
[1] Four- and eight-zone control panels only.
Input circuits should have a maximum resistance of
100 Ω(including any cable resistance).
Sounder outputs
EN 54-2 OUT1, OUT2, and OUT3
EN 54-2 Evacuation OUT1, OUT2, OUT3, and OUT4
EN 54-2 Scandinavia OUT1, OUT2, and OUT3
BS 5839-1 OUT1, OUT2, OUT3, and OUT4
NBN S21-100 OUT1 and OUT2 (Evacuation sounders)
OUT3 and OUT4 (Warning sounders)
NEN 2535 OUT1 and OUT2

2 1X-F Series Quick Installation Guide
Fire routing outputs
EN 54-2 OUT4
EN 54-2 Scandinavia OUT4
NEN 2535 OUT3 (automatic)
OUT4 (manual)
Mains fuses and batteries
Mains fuses
110 VAC [1] T 3.15A 250V
240 VAC T 2A 250V
[1] See your installation manual for 110 VAC operation requirements.
Batteries
Two- and four-zone panels 12 V, 7.2 Ah
Eight-zone panel 12 V, 7.2 Ah or 12 V, 12 Ah
Basic configuration
Default configuration
Operating mode 01 (EN 54-2)
Zone end-of-line Passive
Zone type Mixed
The configuration controls are located on the control
panel interface.
Configuration controls
Button Function
1 Scroll to the next configuration menu on the seven-
segment display.
2 Scroll to the next configuration value for the active menu
on the seven-segment display.
3 Scroll to the previous configuration menu on the seven-
segment display.
4 Scroll to the previous configuration value for the active
menu on the seven-segment display.
Enter Confirm a menu selection or a value selection entry.
The configuration controls are also used to enter the
user level password. The seven-segment display is
visible when the control panel cover is removed.
Seven-segment display
LED Indications
Mode Steady: Select a menu using buttons 1 and 3.
— or —
Flashing: Select a submenu using buttons 1 and 3.
Value Steady: Select a value using buttons 2 and 4.
Basic configuration menu
Selected options from the basic configuration menu are
shown below. The default password for basic
configuration is 3333.
Display Menu Values
Basic default
configuration
01 to 32
Sounder delay 00 to 10 minutes
Fire routing delay 00 to 10 minutes
Extended fire routing
delay
00 to 10 minutes
Restore previous
configuration
Restore factory
configuration
Exit without saving
Exit and save

1X-F Series Quick Installation Guide 3
Basic default configuration presets
A selected list of basic default configuration presets is
shown below. For a detailed list of all available
configuration presets and characteristics, see your
installation manual.
Display Operating mode Zone type
01 EN 54-2 Mixed
05 EN 54-2 Evacuation Mixed
07 EN 54-2 Scandinavia Mixed
11 BS 5839-1 [1] Mixed
21 NBN S21-100 Odd zones: Automatic
Even zones: Manual
31 NEN 2535 Odd zones: Automatic
Even zones: Manual
[1] Requires an active end-of-line device for zone termination.
Contact information
For contact information, see
www.utcfireandsecurity.com.
Copyright © 2011 UTC Fire & Security. All rights
reserved.

4 1X-F Series Quick Installation Guide