Art's-Way Manufacturing Forage Box User manual

Art’s-Way Manufacturing Co., Inc.
Forage Box
Operator’s Manual
MP16.21265
Issued 04-2009
O P E R A T O R ’S M A N U A L

This symbol means ATTENTION! BECOME ALERT! YOUR
SAFETY IS INVOLVED. The message that follows the symbol
contains important information about your safety. Carefully read
the message. Make sure you fully understand the causes of
possible injury or death.
IF THIS MACHINE IS USED BY AN EMPLOYEE, IS LOANED, OR IS RENTED, MAKE
SURE THAT THE OPERATOR UNDERSTANDS THE TWO INSTRUCTIONS BELOW.
BEFORE THE OPERATOR STARTS THE ENGINE:
1. GIVE INSTRUCTIONS TO THE OPERATOR ABOUT SAFE AND CORRECT USE OF
THE MACHINE.
2. MAKE SURE THE OPERATOR READS AND UNDERSTANDS THE OPERATOR’S
MANUAL FOR THIS MACHINE.
WARNING
IMPROPER OPERATION OF THIS MACHINE CAN CAUSE INJURY OR
DEATH.
BEFORE STARTING THE ENGINE, DO THE FOLLOWING:
1. READ THE OPERATOR’S MANUAL.
2. READ ALL SAFETY DECALS ON THE MACHINE.
3. CLEAR THE AREA OF OTHER PERSONS.
LEARN AND PRACTICE SAFE USE OF MACHINE CONTROLS IN A
SAFE AND CLEAR AREA BEFORE YOU OPERATE THIS MACHINE ON
A JOB SITE.
It is your responsibility to observe pertinent laws and regulations and to
follow manufacturer’s instructions on machine operation and maintenance.
See your Authorized Art’s-Way Manufacturing Co., Inc. dealer or
Art’s-Way Manufacturing Co., Inc. for additional operator’s manuals,
illustrated parts catalogs, and service manuals.

FORAGE BOX OPERATORS MANUAL - TO THE OWNER 1
Manual No. MP16.21265 - Issued April 2009
TO THE OWNER
Congratulations on the purchase of your new Art’s-Way Forage Box. You have selected a top quality machine that is
designed and built with pride to ensure you have many years of efficient and reliable service.
Many people have worked on the design, production, and delivery of this Forage Box. The information in this manual is
based on the knowledge, study, and experience through years of specializing in the manufacturing of farm machinery.
This manual is designed to provide you with important information regarding safety, maintenance, and machine operation
so you can and will get the best possible performance from your Forage Box.
Even if you are an experienced operator of this or similar equipment, we ask that you read this manual before operating
the Forage Box.
The way you operate, adjust, and maintain this unit will have much to do with its successful
performance. Any further questions you may have about this product of Art’s-Way equipment should be directed to your
local Art’s-Way dealer or to Art’s-Way Manufacturing Co., Inc., Armstrong, Iowa, [phone].
SPECIFICATIONS AND DESIGN ARE SUBJECT TO CHANGE WITHOUT NOTICE
Art’s-Way Manufacturing Co., Inc. is continually making product improvements. In doing so, we reserve the right to make
changes and/or add improvements to our products without obligation for the equipment previously sold.
Modifications to this Forage Box may affect the performance, function, and safety of its operation. Therefore, no
modification are to be made without the written permission of Art’s-Way Manufacturing Co., Inc. Any modification made
without the written permission of Art’s-Way Mfg. Co. shall void the warranty of this product.
In the interest of continued safe operation of this Forage Box, pay particular attention to the safety alert symbol(s)
throughout this Manual.
ART’S-WAY MANUFACTURING CO.,INC.STATEMENT OF PRODUCT LIABILITY
Art’s-Way Manufacturing Co., Inc. recognizes its responsibility to provide customers with a safe and efficient product.
Art’s-Way Manufacturing Co., attempts to design and manufacture its products in accordance with all accepted
engineering practices effective at the date of design. This statement should not be interpreted to mean that our products
will protect against the user’s own carelessness or failure to follow common safety practices nor will Art’s-Way
Manufacturing Co., be liable for any such act. In addition, Art’s-Way Manufacturing Co. assumes no liability for any altered
product or any modified product by users or anyone other than an authorized dealer.
IMPORTANT WARRANTY INFORMATION
The warranty for this Forage Box appears on page 4 of this manual. In order to establish proper warranty registration, the
Warranty Registration must be completed and returned to the factory within 30 days. Failure to comply with this
requirement may result in reduced warranty allowances.
LIMITATIONS OF THIS MANUAL
This manual contains operating instructions for your Forage Box only. Any mention of other machinery in this manual
other than the Forage Box is for reference only. This manual does not replace nor is it to be used for any machinery that
may be attached to or used in conjunction with the Forage Box.

2 FORAGE BOX OPERATORS MANUAL - PARTS & SERVICE
Manual No. MP16.21265 - Issued April 2009
PARTS & SERVICE
As the purchaser of your new Forage Box, it is very important to consider the following factors:
A. Original Quality
B. Availability of Service Parts
C. Availability of Adequate Service Facilities
Art’s-Way Manufacturing Co., Inc. has an excellent dealership network ready to answer any questions you may have
about your Forage Box. Parts for your machine may be ordered through our dealers. When placing a parts order, please
have the model and serial number ready. This will allow the dealer to fill your order as quickly as possible.
For your convenience, we have provided this space for you to record your model number, serial number, and the date of
purchase, as well as your dealer’s name and address.
Owner’s Name:
Owner’s Address:
Purchase Date:
Dealership Name:
Dealership Address:
Dealership Phone No.:
Machine Serial Number Location
The placard containing the serial and model
number is located on the front
left-hand side of the Forage Box.
Enter the serial number and model of your
Forage Box within the space provided.
Figure 2 - Location of Serial & Model
Number Placard on Forage Box
Figure 1 - Serial and Model Number
Placard

FORAGE BOX OPERATORS MANUAL -TABLE OF CONTENTS 3
Manual No. MP16.21265 - Issued April 2009
TABLE OF CONTENTS
TO THE OWNER .................................................. 1
SPECIFICATIONS AND DESIGN AR E SUBJECT TO
CHANGE WITHOUT NOTICE .......................................... 1
ART’S-WAY MANUFACTURING CO.,INC.STATEMENT
OF PRODUCT LIABILITY................................................ 1
IMPORTANT WARRANTY INFORMATION........................... 1
LIMITATIONSOFTHISMANUAL....................................... 1
PARTS & SERVICE.............................................. 2
TABLE OF CONTENTS ....................................... 3
LIMITED WARRANTY.......................................... 4
PRE-DELIVERY CHECKLIST (CUSTOMER)...... 5
PRE-DELIVERY CHECK LIST ................................. 5
DELIVERY CHECK LIST.......................................... 5
PRE-DELIVERY CHECKLIST (DEALER)............ 6
PRE-DELIVERY CHECK LIST ................................. 6
DELIVERY CHECK LIST.......................................... 6
SAFETY FIRST..................................................... 7
NOTICES OF DANGER,WARNING,AND CAUTION............ 7
SAFETY GUIDELINES......................................... 8
POWER SOURCE SHUTDOWN PROCEDURE ...... 8
BEFORE OPERATING ................................................... 8
DURING OPERATION.................................................... 9
MAINTENANCE SAFETY ................................................ 9
HYDRAULIC SAFETY .................................................... 9
TRANSPORTATION SAFETY ........................................... 9
STORAGE SAFETY..................................................... 10
TIRE SAFETY ............................................................ 10
ASSEMBLY SAFETY.................................................... 10
GENERAL INFORMATION ................................ 11
IDENTIFYING TERMS ........................................... 11
TRACTORS............................................................ 11
WARRANTY REGISTRATION............................... 11
OPERATING AND SAFTEY EQUIPMENT ........ 12
SHIELDS................................................................... 12
Hinged Shields .................................................. 12
Front Access Shield........................................... 12
EMERGENCY CLUTCH BAR AND CABLE........................ 12
SAFETY/CROSS CONVEYOR CLUTCH........................... 13
MAIN CLUTCH ........................................................... 13
MAIN AP R O N SHIFT LEVER......................................... 13
FRONT PTO GU AR D .................................................. 13
ROTATING PTO GUARD............................................. 13
PTO TRANSPORT BRACKET....................................... 13
HINGED SH I E L DS ....................................................... 13
UNLOADING OPERATION -LEFT HAND UNLOAD ............ 14
REAR SHIELD............................................................ 14
SAFETY LABEL LOCATION............................. 15
FRONT/COMBO UNLOADING SAFETY DECALS............... 16
REAR UNLOADING SAFETY DECALS ............................ 20
SET-UP INSTRUCTIONS................................... 22
SMV EMBLEM...........................................................22
MOUNTING FORAGE BOX TO RUNNING GEAR ...............22
SADDLE MOUNTING ...................................................22
TANDEM TIRE BRACKET .............................................23
MOUNTING FORAGE BOX TO RUNNING GEAR ...............23
CROSS CONVEYOR APRON.........................................23
OPERATION INSTRUCTIONS...........................25
LOADING...................................................................25
TRANSPORTING .........................................................25
CAPACITY .................................................................25
TRACTOR CONNECTIONS............................................25
PTO ATTACHMENT PROCEDURE .................................26
FRONT UNLOADING .............................................26
REAR UNLOADING-MECHANICAL.................................26
REAR UNLOADING-HYDRAULIC ...................................27
SHIFTING THE DRIVE COUPLER FROM REAR UNLOAD
TO FRONT UNLOAD....................................................27
ENTERING BOX FOR MANUAL UNLOAD.........................27
LUBRICATION....................................................29
MAIN AP R O N AN D BEATER DRIVE GEARBOX.................29
GREASE AND OIL .......................................................29
SAFETY/CROSS AND MAIN CLUTCH HANDLES...............31
RIGHT ANGLE GEARBOX.............................................31
Mechanical Drive ...............................................31
Hydraulic Drive...................................................32
ADJUSTMENTS..................................................33
MAIN APRON.............................................................33
CROSS CONVEYOR APRON.........................................33
FRONT DRIVE CHAIN..................................................34
SAFETY/CROSS CONVEYOR AND MAIN DRIVE CL U TC H ..34
APRON DRIVE CHAIN .................................................34
BEATER DRIVE CHAINS ..............................................34
REAR APRON DRIVE CHAIN ........................................34
HYDRAULIC DRIVE CHAIN ...........................................35
SHEAR BOLTS ...........................................................35
FASTENERS ..............................................................35
STORAGE .................................................................35
OPTIONS AND ACCESSORIES ........................36
TORQUE SPECIFICATIONS..............................37
TIGHTEN HYDRULIC FITTINGS........................38
TIGHTENING FLARE TYPE FITTINGS .............................38
TIGHTENING O-RING FITTINGS....................................38
SPECIFICATIONS ..............................................39
GENERAL..................................................................39
Model .................................................................39
Height.................................................................39
Width..................................................................39
Length................................................................39
Weight (With Roof).............................................39
Power Source ....................................................39
Capacity.............................................................39
SAE Bolt Identification........................................39

4LIMITED WARRANTY
LIMITED WARRANTY
Art’s-Way Manufacturing Co., Inc. warrants the products it sells to be free from defects in
material and workmanship for a period of one (1) year after the date of delivery to the first
(original) purchaser, subject to the following conditions:
• Art’s-Way Manufacturing Co., Inc. obligation and liability under this
warranty is to repair or replace (at the company’s option) any parts that
upon manufacture were defective in material or workmanship.
• All parts and repairs under this warranty shall be supplied at Art’s-Way
Manufacturing Co., Inc. or an authorized Art’s-Way Manufacturing Co.,
Inc. dealer, at the option of Art’s-Way Manufacturing Co., Inc.
• Art’s-Way Manufacturing Co., Inc. warranty does not extend to parts
and elements not manufactured by Art’s-Way Manufacturing Co., Inc.
and which carry the warranty of other manufacturers.
• Transportation or shipping to an authorized dealer for necessary
repairs is at the expense of the purchaser.
• Art’s-Way Manufacturing Co., Inc. makes no other warranty expressed
or implied and makes no warranty of merchantability or fitness for any
particular purpose beyond that expressly stated in this warranty. Art’s-
Way Manufacturing Co., Inc. liability is limited to the terms set forth in
this warranty and does not include any liability for direct, indirect,
incidental or consequential damages or expenses of delay and the
Company’s liability is limited to repair or replacement of defective parts
as set forth herein.
• Any improper use and/or maintenance, including operation after
discovery of defective or worn parts, operation beyond the rated
capacity, substitution of parts not approved by Art’s-Way
Manufacturing Co., Inc., or any alternation or repair by other than an
authorized Art’s-Way Manufacturing Co., Inc. dealer which affects the
product materially and adversely, shall void the warranty.
• No dealer, employee or representative is authorized to change this
warranty in any way or grant any other warranty unless such change is
made in writing and signed by an officer of Art’s-Way Manufacturing
Co., Inc.
• Some states do not allow limitations on how long an implied warranty
lasts or exclusions of, or limitations on relief such as incidental or
consequential damages, so the above limitations or exclusions may
not apply to you. This warranty gives you the specific legal rights and
you may have other rights that vary from state to state.

FORAGE BOX OPERATORS MANUAL - PRE-DELIVERY CHECKLIST (CUSTOMER) 5
Manual No. MP16.21265 - Issued April 2009
PRE-DELIVERY CHECKLIST (CUSTOMER)
PRE-DELIVERY CHECK LIST
After the Forage Box has been completely set-up, check to be certain it is in correct running order before delivering it to
the customer. The following is a list of points to inspect. Check off each item as you have made the proper adjustments
and found the item operating satisfactorily. Any adjustment must be made according to specifications defined in this
manual.
•All shields and guards are in place and fastened.
•Safety bar and cable operate properly.
•Position and fasten the rear saddle to main stringers, per instructions on page 22.
•All grease fittings have been lubricated and gear box filled to proper level and all chains are oiled. See
“Lubrication” section in this manual.
•All mechanisms are operating trouble free.
•All roller chains are at proper tension. See “Adjustments” section in this manual.
•All bolts and other fasteners are tight.
•PTO shields turn freely, if equipped.
•Apron chains are adjusted properly. See “Adjustments” section in this manual.
•Rear door opens, closes and latches properly, if applicable.
DELIVERY CHECK LIST
The following check list is an important reminder of valuable information that MUST be passed on to the customer at the
time the unit is delivered. Check off each item as you explain it to the customer.
•Give the customer his Operator’s Manual and PTO Manual. Instruct them to be sure to read and completely
understand their contents BEFORE attempting to operate the unit.
•Explain the warranty.
•Explain and review with the customer the Safety Precautions section of this manual.
•Explain and review with the customer the Operating and Safety Equipment section of this manual.
•Explain that regular lubrication and proper adjustments are required for continued proper operation and long life.
Review with the customer the Maintenance and Adjustments sections of this manual.
•Demonstrate the Safety/Cross Conveyor Clutch operation and activation. Also demonstrate the PTO Shaft
Locking Device, Main Clutch and Shift Lever mechanisms, if equipped.
•Advise the customer to check for proper Apron and Roller Chain tension after the second load has been
unloaded and to continue to check the tension until the initial give or slack in the apron disappears.
•Complete the Delivery Registration Card and have customer sign it and return it to Art’s-Way Mfg. Co.
•Demonstrate the proper way to switch from front unload to rear unload and back. I acknowledge that above
points were reviewed with me at the time of delivery, if applicable.
Dealer’s Name
Pre-Delivery Inspector Name
Date of Inspection
Customer’s Signature
Model No.
Serial No
Date Delivered

6 FORAGE BOX OPERATORS MANUAL – PRE-DELIVERY CHECKLIST (DEALER)
Manual No. MP16.21265 - Issued April 2009
PRE-DELIVERY CHECKLIST (DEALER)
PRE-DELIVERY CHECK LIST
After the Forage Box has been completely set-up, check to be certain it is in correct running order before delivering it to
the customer. The following is a list of points to inspect. Check off each item as you have made the proper adjustments
and found the item operating satisfactorily. Any adjustment must be made according to specifications defined in this
manual.
•All shields and guards are in place and fastened.
•Safety bar and cable operate properly.
•Position and fasten the rear saddle to main stringers, per instructions on page 22.
•All grease fittings have been lubricated and gear box filled to proper level and all chains are oiled. See
“Lubrication” section in this manual.
•All mechanisms are operating trouble free.
•All roller chains are at proper tension. See “Adjustments” section in this manual.
•All bolts and other fasteners are tight.
•PTO shields turn freely, if equipped.
•Apron chains are adjusted properly. See “Adjustments” section in this manual.
•Rear door opens, closes and latches properly, if applicable.
DELIVERY CHECK LIST
The following check list is an important reminder of valuable information that MUST be passed on to the customer at the
time the unit is delivered. Check off each item as you explain it to the customer.
•Give the customer his Operator’s Manual and PTO Manual. Instruct them to be sure to read and completely
understand their contents BEFORE attempting to operate the unit.
•Explain the warranty.
•Explain and review with the customer the Safety Precautions section of this manual.
•Explain and review with the customer the Operating and Safety Equipment section of this manual.
•Explain that regular lubrication and proper adjustments are required for continued proper operation and long life.
Review with the customer the Maintenance and Adjustments sections of this manual.
•Demonstrate the Safety/Cross Conveyor Clutch operation and activation. Also demonstrate the PTO Shaft
Locking Device, Main Clutch and Shift Lever mechanisms, if equipped.
•Advise the customer to check for proper Apron and Roller Chain tension after the second load has been
unloaded and to continue to check the tension until the initial give or slack in the apron disappears.
•Complete the Delivery Registration Card and have customer sign it and return it to Art’s-Way Mfg. Co.
•Demonstrate the proper way to switch from front unload to rear unload and back. I acknowledge that above
points were reviewed with me at the time of delivery, if applicable.
Dealer’s Name
Pre-Delivery Inspector Name
Date of Inspection
Customer’s Signature
Model No.
Serial No
Date Delivered

FORAGE BOX OPERATORS MANUAL -SAFETY FIRST 7
Manual No. MP16.21265 - Issued April 2009
SAFETY FIRST
“A careful operator is the best insurance against an accident”
(National Safety Council)
Most accidents can be prevented if the operator:
•Fully understands how the machine functions
•Can anticipate situations which may produce problems
•Can make necessary corrections before problems develop
THIS SYMBOL MEANS
ATTENTION!
BECOME ALERT!
YOUR SAFETY IS INVOLVED!
The American Society of Agricultural Engineers has adopted the Universal Safety Alert Symbol as a way to identify areas
of potential danger if the equipment is not operated correctly. Please be alert whenever you see this symbol in the
manuals or on your forage box.
Art’s-Way Manufacturing Co., Inc. strives to make our equipment as safe as possible. The Art’s-W a y Forage Box
conforms to applicable safety standards at the time of manufacturing. A safety conscious equipment operator makes an
effective accident-prevention program complete.
Safety features and instructions for the forage box are detailed in the Safety Guidelines section of this Operator’s Manual.
It is the responsibility of the owner to ensure that all operators read and understand the manual before they are allowed to
operate the forage box. (Occupational Safety and Health Administration (OSHA) regulations 1928.57.)
N OTICES O F D ANGER , W ARNING , A ND C AUTION
Signal Words: Note the use of signal words D A N G E R , WARNING,and CAUTION on the Forage Box and in this manual.
The appropriate signal word for each has been selected using the following guidelines:
Figure 3 - Universal Safety Alert Symbol
D A N G E R : I M M E D I A T E A N D SPECIFIC HAZARD WHICH WILL RESULT
IN SEVERE PERSONAL INJURY OR DEATH IF PROPER
PRECAUTIONS ARE NOT T A K E N .
WARNING: SPECIFIC HAZARD OR UNSAFE PRACTICE COULD RESULT
IN SEVERE PERSONAL INJURY OR DEATH IF PROPER PRECAUTIONS
ARE NOT TAKEN.
CAUTION: A REMINDER OF GOOD SAFETY PRACTICES. PERSONAL
INJURY COULD RESULT IF PROPER PROCEDURES ARE NOT
FOLLOWED.

8 FORAGE BOX OPERATORS MANUAL - SAFETY GUIDELINES
Manual No. MP16.21265 - Issued April 2009
SAFETY GUIDELINES
Remember:
“The Best Operator is a Safe Operator”
CAUTION: BEFORE YOU ATTEMPT TO
OPERATE THIS FORAGE BOX, READ AND
STUDY THE FOLLOWING SAFETY
INFORMATION. IN ADDITION, MAKE SURE
THAT EVERY INDIVIDUAL WHO OPERATES
OR WORKS WITH THIS EQUIPMENT,
WHETHER FAMILY MEMBER OR
EMPLOYEE, IS FAMILIAR WITH THESE
SAFETY PRECAUTIONS. A R T ’ S -W A Y M F G .
CO. PROVIDES GUARDS FOR EXPOSED
MOVING PARTS FOR THE OPERATOR’S
PROTECTION; HOWEVER, SOME AREAS
CANNOT BE GUARDED OR SHIELDED IN
ORDER TO ASSURE PROPER OPERATION.
THE OPERATOR’S MANUAL AND DECALS
ON THE MACHINE ITSELF WARN YOU OF
DANGERS AND SHOULD BE READ AND
OBSERVED CLOSELY.
CAUTION: SOME PHOTOGRAPHS USED
HEREIN MAY SHOW DOORS, GUARDS AND
SHIELDS OPENED AND REMOVED. BE
SURE THAT ALL DOORS, GUARDS AND
SHIELDS ARE FASTENED IN THEIR
PROPER POSITION BEFORE MACHINE IS
OPERATED.
POWER SOURCE SHUTDOWN
PROCEDURE
Before cleaning, unclogging, adjusting, lubricating or
servicing this machine perform the following:
•Disengage the tractor PTO. (Mechanical Unload)
•Shut off the tractor engine, remove the starter key and
take it with you.
•Wait for all machine motion to stop.
•Remove the telescoping PTO driveline and ALL
power connections from the tractor.
•Move the tractor remote hydraulic lever to neutral
(Hydraulic unload)
WARNING: FAILURE TO FOLLOW THESE
PRECAUTIONS COULD RESULT IN DEATH
OR SERIOUS INJURY.
BEFORE OPERATING
•Clear the area of bystanders, especially children,
when making repairs, adjustments or performing
maintenance on the forage box.
•Do not wear loose fitting clothing as it may catch in
moving parts.
•Do not allow riders.
•KNOW how to stop the unloading unit of the forage
box before starting it.
•Do not enter the forage box unless you follow
instructions on page 27.
•See special instructions for operating right-hand
unload forage boxes on page 14.
•Make sure to install and/or secure all guards and
shields, including the tractor power take-off (PTO)
master shield, before starting or operating the forage
box.
•Do not use PTO or PTO guard as a step.
•Do not connect a 1000 RPM tractor PTO shaft onto
this unit.
•Do not use a PTO adapter.
•Be sure that the correct implement driveline parts are
used and that they are properly secured.
•Put all tractor and machine controls in “neutral” and
disengage the PTO before starting. Follow the starting
instructions according to your tractor manual.
•Make sure the locking device on the telescoping PTO
drive shaft is engaged onto the tractor PTO shaft
groove before starting the tractor engine.
•Make sure the rotating shields that are on the
telescoping PTO drive shaft turns freely before
starting the tractor engine.
•Install the safety chain when attaching the forage box
to the tractor.
•Make sure the unit is adequately supported with
safety blocks or safety stands when changing tires or
performing maintenance.
•BE SURE all guards, doors and shields are in place
and properly secured before starting the tractor
engine.
•KEEP hands, feet and clothing away from chains,
augers and PTO when they are moving.
•DO NOT allow minors to be near the machine unless
properly supervised.
•KEEP the forage box away from power lines. Contact
with electrical lines may result in serious injury or
death by electrocution.

FORAGE BOX OPERATORS MANUAL -SAFETY GUIDELINES 9
Manual No. MP16.21265 - Issued April 2009
•CHECK operation of the emergency clutch and of the
activating mechanisms, safety bar and safety cable
frequently, to insure that they are functioning properly.
CAUTION: KEEP WELL CLEAR OF MOVING
PARTS. BE SURE TO SHUT OFF THE
TRACTOR, SET THE PARKING BRAKE, PUT
THE MACHINE IN NEUTRAL, AND REMOVE
THE TRACTOR KEY WHILE M A K ING
ADJUSTMENTS. WAIT FOR ALL
MOVEMENT TO STOP BEFORE
APPROACHING THE MACHINE.
DURING OPERATION
•Keep hands, feet, hair, and clothing away from
moving parts.
•Keep all shields and guards in place and in good
working condition.
•Keep all bystanders, especially children, away from
the forage box while in operation.
•Do not allow riders while the forage box is in
operation.
•Do not attempt to unclog, clean, or adjust the forage
box while it is running.
•Stay away from overhead power lines. Electrocution
can occur even without direct contact.
•Do not unclog, adjust, lubricate or service the forage
box unless the "Power Source Shut Down Procedure"
has been performed (Page 8).
•ALWAYS engage the tractor parking brake before
proceeding to unload the forage box.
•Keep all hydraulic lines, fittings, and couplers tight
and free of leaks. (Refer to Safety Guidelines –
Hydraulic Safety.)
•Use caution when ascending or descending on the
forage box. Wet shoes or boots are slippery.
MAINTENANCE SAFETY
•Follow all operating, maintenance and safety
instructions found in this Manual.
•Before servicing, adjusting, repairing or unclogging
the machine, always make sure the tractor engine is
stopped, key in your pocket, all controls are placed in
neutral, the parking brake is set, and all the moving
parts have stopped.
•Use sufficient tools, jacks, and hoists that have the
capacity for the job.
•Use support blocks or safety stands when changing
tires or performing maintenance.
•Follow good shop practices of keeping the service
area clean and dry and use adequate light for the job
at hand.
•Before applying pressure to the hydraulic system,
make sure all lines, fittings and couplers are tightly
secured and in good condition.
•Make sure all shields/guards are in place and properly
secured when performing maintenance.
HYDRAULIC SAFETY
•On a hydraulic drive, refer to the tractor operators’
manual for proper operation of hydraulic controls.
•Make sure components in the hydraulic system are
kept clean and in good working condition.
•Relieve pressure from the hydraulic system before
servicing or disconnecting from the tractor.
•Keep all hydraulic lines, fittings, and couplers tightly
secured and free of leaks.
•Replace any worn, cut, abraded, flattened or crimped
hoses.
•Do not make any temporary repairs to the hydraulic
lines, fittings or hoses using tape, clamps, or cement.
The hydraulic system operates under extremely high
pressure and temporary repairs may fail suddenly and
create a hazardous/dangerous situation.
•Wear proper hand and eye protection when searching
for a high-pressure hydraulic leak. Use a piece of
wood or cardboard as a backstop instead of hands to
identify and isolate a leak. If injured by a concentrated
high-pressure stream of hydraulic fluid, seek medical
attention immediately. Serious infection or toxic
reaction can develop if hydraulic fluid penetrates the
surface of the skin.
•Before applying pressure to the system, make sure all
components are tight and that the hydraulic lines,
hoses and couplings are not damaged.
TRANSPORTATION SAFETY
•Make sure the forage box complies with all local
regulations regarding transporting equipment on
public roads and highways.
•Make sure the Slow Moving Vehicle (SMV) emblem
and all lights and reflectors required by local highway
and transportation authorities are properly in place,
clean and clearly visible to traffic.
•Do not allow riders on any machinery during
transport.
•Make sure the forage box is securely attached to the
tractor and install a safety chain to the forage box.
•Make sure the tractor brake pedals are latched
together.
•Do not exceed 20 mph (32 km/h) when transporting
the forage box. Always reduce speed on rough roads
and surfaces, or when going down inclines.
•Use caution when turning and always use the turn
signals on the tractor to indicate your turning
intentions to the other traffic.
•The weight of the trailed machine should NEVER
exceed the weight of the towing vehicle.

10 FORAGE BOX OPERATORS MANUAL - SAFETY GUIDELINES
Manual No. MP16.21265 - Issued April 2009
•Check all clearances carefully whenever the machine
is towed.
•Stay away from overhead obstructions and power
lines during transport. Electrocution can occur even
without direct contact.
STORAGE SAFETY
•Store the forage box in an area away from human
activity.
•Do not permit children to play on or around the stored
machine at any time.
•Make sure that the forage box is stored in an area
with a firm and level base to prevent the machine
from tipping or sinking into the ground.
•Block the wheels to prevent the machine from rolling.
TIRE SAFETY
•USE ONLY properly rated running gear and tires.
•Have only a qualified tire dealer or tire repair service
perform tire repairs.
•Do not attempt to install a tire on a wheel or rim
unless you have the proper equipment and
experience to do the job.
•Follow proper procedures when installing a tire on a
wheel or rim to prevent an explosion that could result
in serious injury.
•Do not substitute tires with a lesser road rating and/or
capacity for the original equipment tires.
CAUTION: FAILURE TO FOLLOW PROPER
PROCEDURES WHEN INSTALLING A TIRE
ON A WHEEL OR RIM CAN PRODUCE AN
EXPLOSION THAT MAY RESULT IN
SERIOUS INJURY OR DEATH. DO NOT
ATTEMPT TO INSTALL A TIRE UNLESS
YOU HAVE THE PROPER EQUIPMENT AND
EXPERIENCE TO PERFORM THE JOB.
REPLACEMENT, REPAIR, AND/OR
MAINTENANCE SHOULD BE DONE BY A
QUALIFIED TIRE DEALER OR QUALIFIED
REPAIR SERVICE.
ASSEMBLY SAFETY
•Use adequate manpower to perform assembly
procedures safely.
•Assemble the forage box in an area with sufficient
space to maneuver the largest components and allow
easy access to all sides of the machine.
•Use only forklifts, lift cranes, jacks and tools with
sufficient capacity for the loads.
•Do not allow spectators, especially children, in the
working area.
Remember:
“The Best Operator is a Safe Operator

FORAGE BOX OPERATORS MANUAL –GENERAL INFORMATION 11
Manual No. MP16.21265 - Issued April 2009
GENERAL INFORMATION
The purpose of this manual is to assist the operator in
maintaining and operating the Forage Box. Read it
carefully: it furnishes information and instructions that
will help you achieve years of dependable service.
Each section of this manual is clearly identified and is
divided into smaller sections.
All replacement parts should be obtained from or
ordered through your Art’s-Way Mfg. Co. dealer. Give
complete information when ordering service parts
including the model number and serial numbers. Record
numbers in the space provided as a handy record for
quick reference.
Model No.
Serial No.
Date Purchased
Numbers for this unit are stamped on a plate located on
the left-hand frame of the unit. Art’s-Way Mfg. Co.
reserves the right to make improvements in design, or
changes in specifications at any time, without incurring
any obligation to owners of units previously sold.
IDENTIFYING TERMS
“LEFT” and “RIGHT” are determined from a position
standing at the rear of the unit looking toward the
direction of travel. From this position if the cross
conveyor on the front of the unloading unit discharges
from the “Right” side, you have a Right Hand machine
and conversely, if it discharges on the “Left” side, you
have a Left Hand machine. “FRONT” is the leading end
and “REAR” is the trailing end when the tractor is
traveling forward.
TRACTORS
This Operator’s Manual uses the term “Tractor” when
identifying the power source for the forage box and the
blower. However, the same safety and operating
practices apply to other power sources such as
hydraulic and electric motors.
WARRANTY REGISTRATION
The DELIVERY AND WARRANTY REGISTRATION
CARD found on page 4 of this manual must be
completed and signed to validate your warranty
protection. You must read and understand the places
where you attest to having received instructions as to
care, adjustments, safe operation and applicable
warranty policy. The terms and conditions of the
warranty are specified on the rear cover of this manual.
WARNING: SOME PHOTOGRAPHS USED
HEREIN MAY SHOW DOORS, GUARDS
AND SHIELDS OPENED OR REMOVED.
BE SURE THAT ALL DOORS, GUARDS
AND SHIELDS ARE FASTENED IN THEIR
PROPER POSITION BEFORE MACHINE IS
OPERATED.

12 FORAGE BOX OPERATORS MANUAL – OPERATION AND SAFETY EQUIPMENT
Manual No. MP16.21265 - Issued April 2009
OPERATING AND SAFTEY EQUIPMENT
CAUTION: B E C O M E F A M I L I A R W I T H AND
KNOW HOW TO USE ALL SAFETY
DEVICES AND CONTROLS BEFORE
ATTEMPTING TO OPERATE THIS
EQUIPMENT. KNOW HOW TO STOP THE
UNIT BEFORE STARTING IT.
SHIELDS
CAUTION: DO NOT OPERATE THIS
EQUIPMENT UNLESS ALL SHIELDS ARE
PROPERLY SECURED IN P L A C E .
CAUTION: DO NOT UNCLOG, ADJUST,
LUBRICATE OR SERVICE THE FORAGE
BOX UNLESS THE "POWER SOURCE SHUT
DOWN PROCEDURE" (PAGE 8) HAS BEEN
PERFORMED.
Wherever possible and without affecting machine
operation, shields have been used on this forage box to
protect potentially hazardous areas. In many places,
decals are also provided to warn of potential dangers as
well as to display special operating procedures. Refer to
Safety Label Location section (page 15).
Hinged Shields
Hinged Shields have been provided over the
transmission, beater drive chains and front roller chain
drive. These can be opened for lubrication, adjustment
and/or service access when required. Shields should be
inspected and cleaned periodically to avoid material
build up. (See Figure 4, Item 1 or Figure 5, Item 1 and
2.)
Figure 4 - Hinged Shield (Front/Combo Unload)
Figure 5 - Hinged Shields (Rear Unload)
Front Access Shield
The front apron shafts and idler sprockets are between
the slant panel and front access shield (See Figure 4,
Item 1 or Figure 5, Item 1.). For lubrication and
adjustment see the corresponding sections in the
manual.
EMERGENCY CLUTCH BAR AND CABLE
CAUTION: IN AN EMERGENCY, PUSH THE
SAFETY BAR OR PULL THE SAFETY
CABLE TO TRIP THE SAFETY/CROSS
CONVEYOR CLUTCH AND STOP THE
CROSS CONVEYOR, AUGERS AND MAIN
APRONS.
CAUTION: EMERGENCY STOP DOES NOT
STOP THE FORAGE BOX DRIVE SYSTEM
WHEN BEING OPERATED AS A REAR
UNLOAD.
NOTE: Emergency clutch bar and cable are applicable
to the front and combo only.
To trip the safety/cross conveyor clutch, either push the
safety bar (Figure 6, Item 2) which spans across the
front of the unloading unit or pull the safety cable
(Figure 6, Item 3) which runs over the outfeed. To reset,
rotate safety/cross conveyor clutch lever into "RUN"
position.
Figure 6 - Emergency Clutch Bar And Cable
(Front/Combo Unload Only)

FORAGE BOX OPERATORS MANUAL -OPERATION AND SAFETY EQUIPMENT 13
Manual No. MP16.21265 - Issued April 2009
SAFETY/CROSS CONVEYOR CLUTCH
NOTE: Safety/Cross Conveyor Clutch is applicable to
the front and combo only.
The safety/cross conveyor clutch (Figure 6, Item 4)
allows clearing of the cross conveyor without operation
of the augers or main aprons. This clutch also functions
as a safety reset and is disengaged by pushing the
safety push bar or pulling the safety cable on the side of
the box. (Figure 6, Item 2 and Item 3)
To reset, return the safety/cross conveyor clutch handle
to the "run" position.
MAIN CLUTCH
NOTE: Main Clutch is applicable to the front and combo
only.
The main clutch lever (Figure 6, Item 5) is provided for
stopping and starting the augers and main aprons.
The main clutch is engaged when the lever is in the
"run" position. To disengage the clutch, move the lever
to the "stop" position.
Use of the main clutch lever during unloading is further
explained in the Operating Instructions section of this
manual (page 26).
CAUTION: DISENGAGING THE MAIN
CLUTCH DOES NOT STOP THE CROSS
CONVEYOR. TO STOP THE CROSS
CONVEYOR, THE EMERGENCY PUSH BAR
OR CABLE MUST BE TRIPPED OR
SAFETY/CROSS CONVEYOR CLUTCH
TURNED TO THE STOP POSITION.
MAIN APRON SHIFT LEVER
NOTE: Main Apron Shift Lever is applicable to the front
and combo only.
The shift lever (Figure 6, Item 6) is used only to adjust
the feeding rate of the main aprons. It is marked with
seven positions:
1, Neutral (N); 2, Neutral (N); 3, Neutral (N); and
4 (Sweep).
CAUTION: THE FOURTH OR SWEEP SPEED
SHOULD ONLY BE USED AT THE END OF
THE LOAD FOR CLEAN-OUT AND NOT FOR
NORMAL UNLOADING OPERATION.
FRONT PTO GUARD
NOTE: The Front PTO Guard is applicable to the front
and combo as well as the mechanical drive version of
the rear unload.
A guard is provided over the input drive universal joint
on the front of the unloading unit. (See Figure 5, Item 1
or Figure 6, Item 7.)
CAUTION: DONOTUSETHEPTOGUARD
AS A STEP.
ROTATING PTO GUARD
NOTE: The Front PTO Guard is applicable to the front
and combo as well as the mechanical drive version of
the rear unload.
The telescoping PTO shaft, between the forage box and
the tractor, is equipped with a rotating shield. (See
Figure 5, Item 3 or Figure 7, Item 8.)
Figure 7 - Rotating PTO Guard And PTO Transport
Bracket Emergency Clutch Bar And Cable
(Front/Combo Unload Only)
CAUTION: BE SURE THE ROTATING PTO
SHIELD TURNS FREELY BEFORE
STARTING THE TRACTOR ENGINE.
PTO TRANSPORT BRACKET
NOTE: The Front PTO Guard is applicable to the front
and combo as well as the mechanical drive version of
the rear unload.
A bracket is provided on the front of the unloading unit
to conveniently hold the telescoping PTO drive shaft
during transport.
To safeguard the telescoping PTO drive shaft, be sure
to shut off the tractor engine and disconnect the drive
shaft from the PTO shaft and place it into the bracket
when transporting or filling the forage box. (See Figure 4
5, Item 5 or Figure 7, Item 9.)
HINGED SHIELDS
NOTE: The Hinged Shields are applicable to the front
and combo only.
Hinged shields have been provided over the apron
takeup and rear roller chain drive. These can be opened
for lubrication, adjustment and /or service access when
required. Shields should be inspected and cleaned
periodically to avoid material build up. The rear shield
should be raised and pinned in the open position for
servicing, (Figure 8, Item A). Return the pins to the
storage position when finished, (Figure 8, Item B).
CAUTION: DO NOT LUBRICATE, ADJUST
AND /OR SERVICE UNLESS TRACTOR PTO
IS DISENGAGED AND TRACTOR ENGINE IS
SHUT OFF.

14 FORAGE BOX OPERATORS MANUAL – OPERATION AND SAFETY EQUIPMENT
Manual No. MP16.21265 - Issued April 2009
Figure 8 - Hinged Shields (Front/Combo Unload)
UNLOADING OPERATION -LEFT HAND
UNLOAD
Because forage blowers load from the right side (as
viewed from behind), a left hand forage box will be
stationed next to the forage blower so that the controls
on the forage box as well as those on the blower and
the blower tractor easily can be reached from the
Operator's Position. (See Figure 9).
However, because of building and silo arrangements on
some farms, some customers desire right-hand unload
forage boxes. A right-hand box may be convenient for
positioning the forage box to the blower, but it limits
easy access of the forage box operator to the controls
on the blower and the blower tractor. Accordingly, a
right-hand unload forage box will be stationed so that
the control on the blower and blower tractor can safely
be reached only by the operator leaving the Operator’s
position and walking around the forage box tractor and
the forage box itself, or if accessible, by walking
between the blower and the silo. (See Figure 10)
Figure 9 - Left-hand Unload
Figure 10 - Right-Hand Unload
WARNING: DO NOT STEP OVER PTO
SHAFT.
WARNING: DO NOT WALK OR CLIMB
BETWEEN FORAGE BOX OUTFEED AREA
AND BLOWER WHEN EITHER FORAGE
BOX OR BLOWER IS OPERATING.
WARNING: DO NOT TAKE A SHORT CUT.
REAR SHIELD
NOTE: The Hinged Shields are applicable to the front
and combo only.
The rear apron shaft and idler sprockets are between
the slant panel and rear access shield. For lubrication
and adjustment see the applicable sections in this
manual. (See Figure 11)
Figure 11 - Rear Shield (Front Unload)

FORAGE BOX OPERATORS MANUAL –SAFETY LABEL LOCATION 15
Manual No. MP16.21265 - Issued April 2009
SAFETY LABEL LOCATION
Each Forage Box has been produced and assembled
with the operator's safety in mind. As a reminder to the
operator of proper operation of the machine, several
labels of warning and instruction have been attached.
Information on labels is, by necessity less than in the
operator's manual. Do not depend solely on the labels
for safe and proper operation. Use your operator's
manual.
CAUTION: DO NOT REMOVE ANY OF
THESE LABELS. THEY ARE FOR YOUR
PROTECTION. TAKE NOTE OF THEIR
MESSAGES AND OBSERVE.
CAUTION: PERIODICALLY CHECK ALL
LABELS AND REPLACE ANY THAT ARE
MISSING, WORN, OR ILLEGIBLE. WHEN
REPLACING, CLEAN MACHINE SURFACE
THOROUGHLY USING SOAP AND WATER
OR CLEANING SOLVENT TO REMOVE DIRT
AND GREASE. CONTACT YOUR DEALER
OR A R T ’ S -WAY MFG. CO. IF ANY LABELS
ARE NOT UNDERSTOOD.
CAUTION: THE FORAGE BOX WAS
DESIGNED AS A FORAGE BOX. DO NOT
USE FOR OTHER PURPOSES.
CAUTION: REPLACE ALL WORN,
DAMAGED, UNUSABLE OR MISSING
SAFETY SHIELDS AND GUARDS.
CONTACT YOUR DEALER.
CAUTION: CLOSE OR REPLACE ALL
COVERS, DOORS OR SHIELDS BEFORE
STARTING THE UNLOADING MECHANISM!

16 FORAGE BOX OPERATORS MANUAL – SAFETY LABEL LOCATION
Manual No. MP16.21265 - Issued April 2009
FRONT/COMBO UNLOADING SAFETY DECALS

FORAGE BOX OPERATORS MANUAL -SAFETY LABEL LOCATION 17
Manual No. MP16.21265 - Issued April 2009
Table 1 - FRONT/COMBO UNLOAD SAFETY DECALS
Ref No.
Part No.
Description
12
MP16.20177
Warning – Rotating PTO Keep Your Body And Clothing Away
13
MP 01.77770
Stop
14
MP 01.77760
Run
15
MP 16.20195
Shift Quadrant (Left-Hand)
16
MP 16.20210
Operating Instructions
17
MP 16.20178
Caution – Before You Operate This Equipment
18
MP 329594B2
Danger – Rotating Driveline
19
MP 01.77810
Emergency Stop Pull
20
MP 16.20181
Warning – Rotating Parts Inside – Keep Your Body And Clothing Away
21
MP 907220
Amber Reflector (Qty 2 Per Side – Not Shown)
22
MP 907219
Red Reflector
23
MP 16.20179
Warning – Replace All Shields Before Operating
24
MP 16.20196
Decal, 4th Gear (Left-Hand)
25
MP 01.77740
Emergency Stop – Push
26
MP 16.10552
Decal, Danger Door
27
MP 17.00165
Decal, Danger (Inside Implement Input Driveline)
A
MP 16.20980
Decal, 540 RPM, Danger
B
MP 16.21200
Decal, Entanglement Danger
C
MP 21.09024
Decal, Hydraulic Fluid Pressure Warning
D
MP 907224
SMV With Steel Backing
MP 907228
PTO Manual

18 FORAGE BOX OPERATORS MANUAL – SAFETY LABEL LOCATION
Manual No. MP16.21265 - Issued April 2009
#12 – MP 16.20177
Warning – Rotating PTO
Keep Your Body And
Clothing Away
#17 - MP 16.20178
Caution – Before You Operate This Equipment
#18 – MP 329594B2
Danger – Rotating Driveline
#19 – MP 01.77810
Emergency Stop Pull
#20 – MP 16.20181
Warning – Rotating Parts Inside – Keep Your Body And Clothing
Away
#23 - MP 16.20179
Warning – Replace All Shields
Before Operating
#25 - MP 01.77740
Emergency Stop – Push
#26 - MP 16.10552
Decal, Danger Door
A r t ’ s -Way Manufacturing at [phone]