ASI 0390 Product manual

1408201234 Rev J 05 August 2015
EZFILL™ SOAP DISPENSER
AUTOMATIC DECK MOUNTED
SOAP DISPENSER FOR
EZFILL™ TOP FILL MULTIFEED KIT
WITH 1.32 GAL . (5L) CONTAINER
INSTALLATION AND MAINTENANCE GUIDE
Model 0390-(n)*

1408201234 Rev J 05 August 2015
1
TABLE OF CONTENTS
2 SUFFIX CODE INDEX AND APPLICATIONS
3 PRE-INSTALLATION INFORMATION
4 PACK CONTENTS
5 TECHNICAL DATA
6-8 INSTALLATION
9 BATTERY REPLACEMENT INSTRUCTIONS
9 MAINTENANCE
10 TROUBLESHOOTING
11 SPARE PARTS LIST
12 WARRANTY
13-14 EZ FILL™ REMOTE CONTROL
Unit Install Date
Unit Location in Facility
Unit S/N (From Label)
Supplied By
Original PO No.
ASI Order No.

1408201234 Rev J 05 August 2015
2
Space Provided For Owner Notes
*SUFFIX CODE INDEX AND APPLICATION
Model № Sux Service Application
Universal Model, Battery Operation
USA/UK/EU Interchangeable Plug Model, AC Adapter Operation
AU Model, AC Adapter Operation
Universal Model, Battery Operation, Six Pack
USA/UK/EU Interchangeable Plug Model, AC Adapter Operation, Six Pack
AU Model, AC Adapter Operation, Six Pack
1A
1AC
3AC
6-1A
6-1AC
6-3AC
Schedule of Model № Sux Codes to replace (n) in Model № and Application

1408201234 Rev J 05 August 2015
3
PRE-INSTALLATION INFORMATION
CHECK CONTENTS
Separate all parts from the packaging and check each part with the
PACK CONTENTS section.
Make sure all parts are received and separated before discarding any
packaging material.
If any parts are missing, do not attempt to install the system until you
obtain the missing parts.
IMPORTANT
Ensure there is adequate space and clearance under the vanity to
accommodate the SD Mounting Shank and Basin Nut in the desired
location before drilling the hole in the counter top.
Ensure there is adequate space to place the pump within reach of the
Com Cable from the SD Shank.
Keep in mind that the location of the user hands, while using the faucet
nearby, should not interfere with the soap dispenser sensor detection
area.
CAUTION
Do not install the soap dispensers facing a mirror or any other electronic
system operated by an infrared sensor.
To prevent reection problems, it is recommended to keep a minimum
distance of 5’ (1.5M) between the soap dispenser sensor and any other
directly facing objects.

1408201234 Rev J 05 August 2015
4
Identify the items and conrm that parts are included.
Automatic SD Body and
vanity mounting hardware
with power cord, Com Cable
w/inline plug connector and
black soap supply tube 1/4”
dia. (Ø6) Nylon ex 36” (914)
long with connector.
Clear 5/16” dia. (Ø8) Flex tube
118” (3000) Supplied coiled and
permanently attached to pump
housing for multifeed Model
numbers 0390-(n)
EZFILL™ pump assembly
with wall bracket, Com Cable
w/inline socket connector,
soap supply tube and
mounting hardware.
Escutcheon
Flange w/O-Ring
Gasket
Basin Nut
Power Plug
Soap
Supply Tube
Connector
Com Plug
Com Socket
Battery Box
6Dx1.5V=9V
Transformer
12V from 100~240 VAC
Power Supply Option
One (1) ONLY either per model
Plug Adapter
conguration per model
PACK CONTENTS EZFILL™ SOAP DISPENSER 0390-(n)

1408201234 Rev J 05 August 2015
5
TECHNICAL DATA
AC Adapter Cong Plug
Per Option (see TDS)
Battery Box w/Extension Cable
per Model Option (see TDS)
All Dim’s inch (mm) NTS
Note Polarity
Power Socket Power Plug
Note Plug
Polarity
Com Socket Com Plug
2-61/64”
(75)
1-1/2” Dia
(Ø38)
4-3/32”
(104)
0-2-1/16”
(0-52)
3-1/4”
(83)
1-3/16”
(30)
Fill
Prime
Button
2-7/8”
(73)
2-3/16”
(55)
8-5/8”
(219)
3-25/32”
(96)
2”
(51)
2”
(51)
Wall Brkt
w/Hdwr
5-3/32”
(129)
36” (914)
29/32” Dia (Ø23)
Model 0390-(n) EZFILL™ Soap Dispenser and Soap Pump for Multifeed System
Soap Viscosity
100-3800cP (mPa•s)
Soap pH
5.5 – 8.5
Soap Type
clear liquid no abrasives
1-7/32
(31)

1408201234 Rev J 05 August 2015
6
INSTALLATION
STEP 1 - INSTALLING THE EZFILL™ SOAP DISPENSING SYSTEM SOAP DISPENSER
1
2
3
4
Drill a hole in the counter top at the
designated location.
Remove and retain the basin nut and
the gasket from the base of the soap
dispenser body, sliding completely
over and o the soap tube, Com and
Power Cables.
Place the soap dispenser shank through
the escutcheon ange (with O-ring
down) into the hole in the counter top.
Slide the gasket, disk and nut over the
black soap tube and both cables and
thread onto the shank and secure it to
deck underside.
Fix the pump to the desired location by
securing the support with the supplied
screws.
For ease of installation preference,
optionally swap steps 3 and 4 while
ensuring pump is within reach range of
Com cable.
Black Nylon 1/4”dia. (Ø6) tube 36”(914)
long is supplied permanently attached
to dispenser head.
Assemble the tube to the connector
on pump by pushing it on(provided on
end of black tube).
Plug the Com cable into the Socket
cable (See Step 8)
MAX 1-3/16”
(Ø30)
MIN 1-1/32”
(Ø26)
36” (914)
tube length
1-1/8” Dia (Ø28)Recommended hole size
36” (914)
tube length

1408201234 Rev J 05 August 2015
7
INSTALLATION
Cut the 5/16”dia (Ø8) soap supply clear
tube coming from the EZFILL™ Pump-
Motor to the right length as required by
the installation.
Connect the EZFill™ Pump-Motor clear
5/16” dia. (Ø8) soap supply tube to any
available locking bushing in the soap tank
cap (see 0390 OM & IG).
Connect the Com Cable motor connector to the mating plug from
dispenser (If not already connected in Step 3 above). Please note
that since the connector is water proof, some friction will apply.
Important: the 4 contacts connector should be inserted fully so that the
white O-ring is not visible and a clicking sound is heard.
NOTICE: If the 4 contacts connectors are not connected properly, the motor
will run continuously.
Remove the protective sticker
covering the sensor. Keep away
from the sensor range.
NOTE: The Multifeed Kit enables soap distribution for up to six (6) soap
dispensers simultaneously. When installing less than a full complement
of soap dispensers, make sure to insert and clamp the 5/16” dia x 1” long
(Ø8x25) plugs into the remaining empty holes provided.
Make sure the end of the tubes are about 1”(25)
longer than required to reach the tank bottom.
5
6
O-RING VISIBLE –
IMPROPERLY CONNECTED
ONLY THE GROOVES ARE VISIBLE -
CONNECTED PROPERLY
7
8
Soap Supply
Tube
Fill
Hose
CONNECTING THE POWER SOURCE

1408201234 Rev J 05 August 2015
8
INSTALLATION
9
CONNECTING THE POWER SOURCE
a. For battery versions:
install the battery box at the
wall underneath the sink
and connect the battery
connector.
Ensure adequate clearance
to allow removal of the top
cover and the battery
carrier tray when battery
change is required.
b. For AC Adapter versions:
plug the adapter into the
power socket and connect
the adapter DC connector.
NOTICE: See 0390-TF OM & IG and TDS to ll system with soap. Check for
leaks at all liquid connections.
FROM
THE SOAP DISPENSER
OBSERVE
POLARITY
OBSERVE
POLARITY
FROM THE TRANSFORMER TO THE SOAP DISPENSER
TO THE
BATTERY BOX

1408201234 Rev J 05 August 2015
9
BATTERY REPLACEMENT INFORMATION
Battery models only
When the batteries weaken, the red indicator light will blink at a constant
rate when the user’s hands are within the sensor range. The batteries must be
replaced within two weeks.
To replace the batteries:
1. Carefully open the battery box, use Phillips drive #2 to remove cover screws
(Fig. 1&2, below)
2. Remove the old batteries from carrier tray (Fig. 3)
3. Replace the used batteries with new D batteries in same polarity (Fig. 3)
DO NOT use steel wool or cleansing agents containing alcohol, acid, abrasives,
or the like. Use of any cleaning or maintenance products containing these
substances could damage the surface of the soap dispenser. For surface
cleaning use ONLY soap and water, then wipe dry with a clean cloth or towel.
When cleaning bathroom tiles or counters, protect the soap dispenser from
any splattering of harsh cleansers.
Care and cleaning of chrome and special nishes- see also PCM document.
NOTE: Do not mix used batteries with new ones.
4. Close the box and re-tighten the screws (Fig. 4) and reconnect battery cable.
1 2 3 4
Important: Spent batteries should not be discarded of with
normal household waste. Contact your local authority for
information on waste disposal and recycling.
MAINTENANCE