Assa Abloy Corbin Russwin TL3700 Series User manual

FM341 07/19
Installation Instructions
Copyright © 2011, 2019, ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
WARNING
This product can expose you to lead
which is known to the state of California
to cause cancer and birth defects or other
reproductive harm. For more information
go to www.P65warnings.ca.gov.
Note
All templates can be found
at www.corbinrusswin.com/
Library/Templates
TL3700 Series
Roseless Tubular Lock
Designer Trim

2
TL3700 Series
Installation Instructions
Designer Trim
FM341 07/19
Copyright © 2011, 2019, ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
TOC Table of Contents
1 Full-Trim (TL3710 & 3720) & Half-Trim (TL3780) Installation......................3
a Install Strike (All) ................................................................3
b Install Spring Housing (All).......................................................3
c Install Latch & Scalp (All).........................................................4
d Install Privacy Plate (TL3720 Only) ...............................................4
e Install Adapter Plates (All) .......................................................5
f Install Half-trim Adapter Plate (TL3780 Only) ....................................5
g Thread Collar (TL3710 & 3720) ..................................................5
h Thread Collar (TL3780) ..........................................................6
i Install Half-Trim Collar (TL3780) .................................................6
j Install Outside Lever (TL3710 & 3720) ...........................................6
k Install Inside Spindle and Adjustment Bolt (All) ..................................6
l Install Inside Lever With Dowel Screw (All).......................................7
2 Full Dummy Trim (TL3770) & Half Dummy Trim (TL3750) Installation ............7
a Insert Dummy Spindle (All) ......................................................7
b Install Adapter Plate Assemblies (TL3770) .......................................8
c Install Adapter Plate Assemblies (TL3750) .......................................8
d Install Collar (TL3770) ...........................................................8
e Install Collar (TL3750) ...........................................................8
f Install Lever (TL3770)............................................................9
g Install Lever (TL3750)............................................................9

3
TL3700 Series
Installation Instructions
Designer Trim
FM341 07/19
Copyright © 2011, 2019, ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
1 Full-Trim (TL3710 & 3720) & Half-Trim (TL3780) Installation
a Install Strike (All)
Install strike with supplied combination screws
Figure1
b Install Spring Housing (All)
Make sure the word
FRONT is right side
up and facing away
from the hinges
Figure2

4
TL3700 Series
Installation Instructions
Designer Trim
FM341 07/19
Copyright © 2011, 2019, ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
1 Full-Trim (TL3710 & 3720) & Half-Trim (TL3780) Installation (cont.)
c Install Latch & Scalp (All)
Note:
• (TL3720 Only) The threaded button on the latch faces the inside of the door (For privacy button).
• Rotate latch head to match door hand (Round side hits strike first).
Figure3
d Install Privacy Plate (TL3720 Only)
Install privacy plate and button on inside of door.
Inside of door
Note:
Privacy plate with bigger
hole goes on inside of door.
Align privacy button
Figure4

5
TL3700 Series
Installation Instructions
Designer Trim
FM341 07/19
Copyright © 2011, 2019, ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
1 Full-Trim (TL3710 & 3720) & Half-Trim (TL3780) Installation (cont.)
e Install Adapter Plates (All)
• Install adapter plates on both sides of door using 3/8"Flat Head Screws.
• Install outside privacy plate and adapter plate.
Outside of Door
Figure5
f Install Half-trim Adapter Plate (TL3780 Only)
Install Half-trim adapter plate on non-trim side of door.
Figure6
g Thread Collar (TL3710 & 3720)
Thread collar onto both sides of door using supplied rubber grip.
Note
Make sure collar is tight up against door
Figure7

6
TL3700 Series
Installation Instructions
Designer Trim
FM341 07/19
Copyright © 2011, 2019, ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
1 Full-Trim (TL3710 & 3720) & Half-Trim (TL3780) Installation (cont.)
h Thread Collar (TL3780)
Thread standard collar on trim side of door.
Note
Make sure collar is tight up against door
i Install Half-Trim Collar (TL3780)
Install Half-trim collar on non-trim side of door.
• Make sure hole on Half-trim collar is facing down
j Install Outside Lever (TL3710 & 3720)
Figure10
k Install Inside Spindle and Adjustment Bolt (All)
The short side of inside spindle (the distance from indent to end of spindle) goes into the latch
Figure11
STANDARD MUSÉO
Lever
Use Correct Spindle Orientation
Bad
Lever
Good
Figure8
Figure9

7
TL3700 Series
Installation Instructions
Designer Trim
FM341 07/19
Copyright © 2011, 2019, ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
1 Full-Trim (TL3710 & 3720) & Half-Trim (TL3780) Installation (cont.)
l Install Inside Lever With Dowel Screw (All)
1. Install Lever.
Figure12
Make sure hole in
adjustment bolt
is aligned with
threaded hole in
inside lever.
1/16"
After dowel screw is installed
there should be less than 1/16"
clearance between adapter
plate and shoulder on lever.
2. Rotate lever and make sure it returns. If lever binds, remove inside lever and un-thread adjustment
bolt 1/2 turn.
2 Full Dummy Trim (TL3770) & Half Dummy Trim (TL3750) Installation
a Insert Dummy Spindle (All)
Insert dummy spindle into adapter plate.
• TL3770 use both adapter plates.
Note
Make sure dummy spindle is aligned.
Figure13

8
TL3700 Series
Installation Instructions
Designer Trim
FM341 07/19
Copyright © 2011, 2019, ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
2 Full Dummy Trim (TL3770) & Half Dummy Trim (TL3750) Installation (cont.)
b Install Adapter Plate Assemblies (TL3770)
Note
Make sure dummy adapter plate is installed on non-trim side of door.
Figure14
c Install Adapter Plate Assemblies (TL3750)
Note
Make sure dummy adapter plate is installed on non-trim side of door .
Figure15
d Install Collar (TL3770)
Install collar on both sides of door using supplied rubber grip.
• Make sure collar is tight up against door.
e Install Collar (TL3750)
Install collar on trim side of door.
• Make sure collar is tight up against door.
Figure16
Figure17

9
TL3700 Series
Installation Instructions
Designer Trim
FM341 07/19
Copyright © 2011, 2019, ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
2 Full Dummy Trim (TL3770) & Half Dummy Trim (TL3750) Installation (cont.)
f Install TL3770 Lever
Install lever on both sides of door with dowel screws
Figure18
g Install TL3750 Lever
Install lever on trim side of door with dowel screw
Figure19

10
TL3700 Series
Installation Instructions
Designer Trim
FM341 07/19
Copyright © 2011, 2019, ASSA ABLOY Access and Egress Hardware Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Access and Egress Hardware Group, Inc. is prohibited.
For installation assistance contact Corbin Russwin
1-800-543-3658 • [e-mail]
Page intentionally left blank.