Assa Abloy Yale nexTouch Technical specifications

1
P/N 80-8470-0900-000 (09-19)
Retrofitting or modifying this product may impact fire rating, safety features and warranty.
Consult with code specifications to ensure compliance with all codes and ratings.
®
nexTouch
Touchscreen and Push Button Exit Device Trim
Installation and Programming Instructions
WARNING
This product can expose you to lead which is known to the state of California to cause
cancer and birth defects or other reproductive harm. For more information go to
www.P65warnings.ca.gov.

2
P/N 80-8470-0900-000 (09-19)
?Before You Begin
Fire
Guard
AA
AA
AA
AA
Optional
Technology Module
template
#3 & #2
1/2"3/4"
Left Hand
Reverse
Right Hand
Reverse
Face a door swinging open
toward you.
If it swings open to the right, it
is a right hand reverse door. If it
swings opens to the left, it is a
left hand reverse door.
Exterior
Outswinging Door
Interior
Optional
Privacy DPS Switch

3
P/N 80-8470-0900-000 (09-19)
1Prepare Door
?Door Position Switch Option
template
Privacy DPS Switch
With Door Position Switch installed
and door closed, all keypad functions
can be disabled by Privacy Button.
!
Drill holes 1/2 way thru
door then complete
from other side to
prevent splitting.
DPS Option
for Privacy Function
Wood Door:
3/8" Dia. Thru to
Hole in Door Face
*Metal Door:
3/4" Dia. Thru to
Hole in Door Face
*Metal Door Installations
Supplied plastic collar MUST
be installed for DPS to function
properly.
!

4
P/N 80-8470-0900-000 (09-19)
Tighten
counter-clockwise
to secure lock.
X
!
Use key to thread
cylinder. Pull key
out of cylinder to
first blade cut for
best operation.
!
2Install Cylinder
?Test Cylinder
iIf using cylinder other than 1-1/8", a new collar must
be used that is sized appropriately for cylinder length.
Test cylinder by turning key counter-clockwise to unlock trim. If
there is any binding then cylinder is not at correct depth and needs
to be threaded further into escutcheon.

5
P/N 80-8470-0900-000 (09-19)
3Change Hand of Trim (if necessary)
!
There is a
spring inside
spindle. Be
sure to keep
spring for
reassembly.
iSet screw should be
located on same side
as lever arm.
1
2
2
11
2
1
2
Right Hand ReverseLeft Hand Reverse
Tighten nut then
loosen just enough
that spindle tab
aligns with top of
hole.
!
!Be sure spring
is inside spindle.
Spindle
Tab
Nut

6
P/N 80-8470-0900-000 (09-19)
4
Do not take
apart outside
assembly.
!
#10-32 x 1" OHPMS
x2
Exit Device
Mounting
Holes
1
2
i
!
Do not tighten
screws until
exit device
installation -Step 5.
2 hinge side screws
hold outside trim
assembly until exit
device is installed.
All 4 screws MUST be
used for proper
installation.
Install Outside Trim Assembly

7
P/N 80-8470-0900-000 (09-19)
Tighten all screws.
i
3
4
Refer to exit device installation instructions
for details of device installation.
!
5Install Exit Device
Test Mechanical Lock Function by Key, Lever and Touchpad
x2
#10-32 x 1" PHMS

8
P/N 80-8470-0900-000 (09-19)
6
Refer to exit device installation instructions
for details of strike installation.
i
3-1/2"
DPS Option
for Privacy Function
*Metal Frame:
3/4" Dia. x 1"
See Instructions with DPS Kit
*Supplied plastic collar MUST
be installed for DPS to function
properly.
!
Install Strike and Optional DPS
x3
Frame
#10-24 PFHMS
!Strike must be centered with exit device bolt. For proper
engagement, door should remain latched and not rattle
when pushed, pulled or shaken in/out.

7
x1
#10-32 x 1-1/2" THPMS
x2
#8 x 3/8" PRH
Sheet Metal
#8 x 1/2" PHWS
Wood
OR
x2
Install Inside Escutcheon Plate
Inside of Door
Optional DPS
2
1
9
P/N 80-8470-0900-000 (09-19)

10
P/N 80-8470-0900-000 (09-19)
8Attach Cables to Inside Escutcheon
Optional
DPS
Connection
Motor
Connection
Keypad
Connection
Reset
Button
External
Power