Assa Abloy SARGENT7800 Series User manual

1-800-727-5477 • www.sargentlock.com
A8257E 4/22
Installation Instructions
7800 & 8200 Series Mortise Lock
Used with Sectional Trim and V Series Indicators
Copyright © 2019, 2020, 2021, 2022, SARGENT Manufacturing Company. All rights reserved. Reproduction in whole or in part without
the express written permission ofSARGENT Manufacturing Company is prohibited. Patent pending and/or patent www.assaabloydss.com/
patents.
WARNING
This product can expose you to
lead which is known to the state of
California to cause cancer and birth
defects or other reproductive harm.
For more information go to www.
P65warnings.ca.gov.
Attention Installer: Improper
installation may result in dam-
age to the product and void the
factory warranty.
WARNING

2
1-800-727-5477 • www.sargentlock.com A8257E 4/22
7800 and 8200 Series Mortise Lock
Installation Instructions
Used with Sectional Trim and V Series Indicators
Copyright © 2019, 2020, 2021, 2022, SARGENT Manufacturing Company. All rights reserved. Reproduction in
whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent
pending and/or patent www.assaabloydss.com/patents.
Tools Required
1
#2 & #3 Phillips
head screwdrivers
Flat blade
screwdriver
1/8"Allen
Wrench
3/32"Drill bit T-20 Torx Screw
with Tamper Pin
Driver
Indicator Variants
2
Depending on function and option ordered, indicators are provided in the following variations, these instructions detail how
to install with cylinder, however other variations follow similar instructions. (Figure1)
Contact factory for any questions.
Figure1
Coin Turn - For
installation
on outside of
door.
Cylinder - For
installation
on inside or
outside of
door.
No input /
blank - For
installation
on inside or
outside of
door.
Thumbturn -
For installation
on inside of
door.
Lock set configuration
3
To set function of multi-function lock or to re-hand, see instructions on lock body.

3
1-800-727-5477 • www.sargentlock.com
7800 and 8200 Series Mortise Lock
Installation Instructions
Used with Sectional Trim and V Series Indicators
Copyright © 2019, 2020, 2021, 2022, SARGENT Manufacturing Company. All rights reserved. Reproduction in
whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent
pending and/or patent www.assaabloydss.com/patents.
A8257E 4/22
Rehanding indicator
4
Indicator spindle cams MUST be oriented correctly per lock function and door mounting location. Verify hand and bevel of
door. (Figure2)
LH
Left Hand
Hinges Left
Open Inward
RH
Right Hand
Hinges Right
Open Inward
LHRB
Left Hand
Reverse Bevel
Hinges Left
Open Outward
RHRB
Right Hand
Reverse Bevel
Hinges Right
Open Outward
Figure2
Note:
Stand on outside of locked door when determining door hand.
Next, verify inside and/or outside indicators are handed correctly,
using Spindle Cam Position chart. (Figure3) If they are handed
correctly, skip to Step 5 "Prepare Door".
If they are not handed correctly:
1. Remove retaining pad and spindle cam from assembly. (Figure4)
2. Position spindle cam in correct direction for door hand. (Figure3)
Important:
• For thumbturn indicators, make sure thumbturn
is positioned in the 12 o’clock direction as
shown. (Figure5)
3. Slide spindle cam post into correct slot of display slide. (Figure4)
4. Re-seat retaining pad into original position.
5. Return indicator to the vacant/unlocked position for installation.
Scan this QR
code for the
Sargent Indicator
Handing Charts
Door Hand: RH / RHRB
Door Hand: LH / LHRB
Outside Indicator
Inside Indicator
Inside Indicator
Outside Indicator
Spindle Cam Position for Locks with Deadbolt
(*and 56 function)
Door Hand: RH / RHRB
Door Hand: LH / LHRB
Outside Indicator
Inside Indicator
Inside Indicator
Outside Indicator
Spindle Cam Position for Locks without
Deadbolt (*except 56 function)
Figure3
Figure4
Spindle
cam
Display
slide slot
Retaining
pad
Thumbturn
position
Figure5

4
1-800-727-5477 • www.sargentlock.com A8257E 4/22
7800 and 8200 Series Mortise Lock
Installation Instructions
Used with Sectional Trim and V Series Indicators
Copyright © 2019, 2020, 2021, 2022, SARGENT Manufacturing Company. All rights reserved. Reproduction in
whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent
pending and/or patent www.assaabloydss.com/patents.
aPrepare Door for Mortise Lock
bInstall Lock
Installation
5
RH door
shown
Inside of door
Outside
of door
Lock
Lock Screws
Figure6
Prepare door for function holes, size, and location according to A7050 door
marker template, if not already prepped.
1. Verify strike location according to template.
Clean out door pocket and door edge of debris.
2. Make sure handing of lock matches handing of door. Slide lock into door. (Figure6)
3. Temporarily hand tighten two (2) lock screws (#12 x 1-1/4"wood screws, or #12-24 x1/2"machine screws).
Notes:
• Keep door open until installation is complete.
• If installing lever onto only one (1) side of door (36 function), see separate instruction sheet A7028.
cPrepare Door for Indicator
Template
Guide
Mark holes
with pencil
Figure7
Control Hub
1. Insert template guide into control hub on side where indicator will be
used. (Figure7)
2. Slide indicator template over template guide.
Important: Make sure the template is properly centered and aligned
to ensure smooth indicator operation.
3. Mark the four (4) hole positions indicated on template.
4. Remove guide and template.
5. If indicators are being used on both sides of door, repeat steps 1
through 4 for opposite side.
6. Remove lock body.
7. Drill four (4) marked holes with 3/32" diameter bit, by 1/2" deep.
8. Reinstall lock body and hand tighten screws.
Note:
If retrofitting over an existing product, ensure door surface is free of chips
and debris around holes so indicator will sit flat against door surface.

5
1-800-727-5477 • www.sargentlock.com
7800 and 8200 Series Mortise Lock
Installation Instructions
Used with Sectional Trim and V Series Indicators
Copyright © 2019, 2020, 2021, 2022, SARGENT Manufacturing Company. All rights reserved. Reproduction in
whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent
pending and/or patent www.assaabloydss.com/patents.
A8257E 4/22
Installation, continued
5
dInstall Levers Inside of door
Inside Lever
Rose
Adapter
Plate
Spindle
#8-32 x
5/8" screws
Outside of door
RH door
shown
Figure8
Set screw
Outside
lever & Rose
Assembly
#6 x 3/8"
screws
Mounting
Plate
Figure9
Figure10
eInstall Indicator Mounting Plate
1. Slide outside lever and rose assembly through door and lock
body, and hold. (Figure8)
2. Slide inside spindle into lock body hub.
3. Slide adapter and plate assembly over spindle.
4. Secure with two (2) #8-32 x 5/8" screws.
5. Install inside rose onto adapter plate.
6. Install inside lever on adapter plate. Secure with set screw.
1. Screw indicator mounting plate to door with four (4) #6 x 3/8"
sheet metal screws. (Figure9)
2. If indicators are being used on both sides of door, repeat step 1
for opposite side.
fInstall Indicator Assembly
1. Verify lock is in unlocked state (turn outside lever to confirm).
2. Verify indicator is in vacant/unlocked position.
3. Assemble indicator assembly onto mounting plate. (Figure10)
4. Secure indicator assembly to door with two (2) machine
screws.
• Use #8-32 x 5/8"screw for top
• Use #8-32 x 3/8"screw for bottom
5. If indicators are being used on both sides of door, repeat steps 1
through 3 for opposite side.
Note:
Torx security screws recommended.

6
1-800-727-5477 • www.sargentlock.com A8257E 4/22
7800 and 8200 Series Mortise Lock
Installation Instructions
Used with Sectional Trim and V Series Indicators
Copyright © 2019, 2020, 2021, 2022, SARGENT Manufacturing Company. All rights reserved. Reproduction in
whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent
pending and/or patent www.assaabloydss.com/patents.
Installation, continued
5
gInstall Cylinders
Cylinder
Cylinder
Clamp
Screw
Figure11
Incorrect
Key and cylinder must be rotated as shown.
Correct
Figure12
Figure13
Lock screw
Outside front
#8-32 x 1/4"
screws Lock
screw
1. Thread cylinder into lock until flush with escutcheon surface. (Figure11)
• Pull key slightly out of cylinder to help thread into lock body.
2. Tighten cylinder clamp screw with #2 Phillips screwdriver.
• Check operation and adjust if necessary.
Notes:
• SARGENT logo must be horizontal and on top. (Figure12)
• If double cylinder function is used, repeat steps 1 and 2 for second
cylinder.
• Removable Core or Interchangeable Core cylinders
require a control key (key stamped with C) to remove and
install the core. This is not provided standard; it must be
requested separately. If requesting 1-bitted control key,
specify 113511 cut.
hInstall Outside Front
1. Tighten the two (2) lock screws completely: (Figure13)
2. Attach outside front with two (2) flat head screws #8-32 x 1/4".
iPerform Functional Check
DO NOT FORCE if resistance is encountered during functional
check. Refer back to Rehanding Indicator (if required) section to ensure
correct handing. Rehand if necessary.
1. Insert key into cylinder (if present) and rotate:
• Ensure there is no friction against lock case or any other
obstructions.
2. Check key retracts latch:
• Key should rotate freely.
3. Throw deadbolt (if present):
• Check key retracts both deadbolt and latch.
4. Test levers:
• Confirm latch and deadbolt (if installed) retract.
5. Verify indicator displays correct status when locked and unlocked.

7
1-800-727-5477 • www.sargentlock.com
7800 and 8200 Series Mortise Lock
Installation Instructions
Used with Sectional Trim and V Series Indicators
Copyright © 2019, 2020, 2021, 2022, SARGENT Manufacturing Company. All rights reserved. Reproduction in
whole or in part without the express written permission ofSARGENT Manufacturing Company is prohibited. Patent
pending and/or patent www.assaabloydss.com/patents.
A8257E 4/22
6
1
2
3
4
5
6
6
7
4A
4B
4C
Figure14
Indicator Parts List
6
Figure14 Description Part Number Req.
1
Sectional Escutcheon - Cylinder 81-0742 x finish
1
Sectional Escutcheon - Coin Turn 82-5635 x finish
Sectional Escutcheon - Thumbturn (Standard) 82-5630 x finish
Sectional Escutcheon - Thumbturn (LB Option) 82-5631 x finish
Sectional Escutcheon - Thumbturn (T1) 82-5632 x finish
Sectional Escutcheon - Thumbturn (T2) 82-5633 x finish
Sectional Escutcheon - Thumbturn (T3) 82-5634 x finish
Sectional Escutcheon - No Input/Blank 81-0742 x finish
2 Indicator Window 81-0811 1
3
Indicator Display Assembly - Green Unlocked / Red Locked 82-5602
1
Indicator Display Assembly - Green Vacant / Red Occupied 82-5603
Indicator Display Assembly - Green Unlocked Icon / Red Locked Icon 82-5604
Indicator Display Assembly - White Unlocked / Red Locked 82-5605
Indicator Display Assembly - White Vacant / Red Occupied 82-5606
Indicator Display Assembly - White Unlocked Icon / Red Locked Icon 82-5607
Indicator Display Assembly - Green Ouvert / Red Fermé 82-5684
Indicator Display Assembly - Green Libre / Red Occupée 82-5685
4A Indicator Spindle Cam - Thumbturn/Coin Turn 81-0745
14B Indicator Spindle Cam - Cylinder/No Input / Blank 81-0756*
4C Indicator Spindle Cam - 05, 37, 38, 59 Function 82-5577*
4D Indicator Spindle Cam - 05 (Inside) 82-5673 1
5 Indicator Retaining Pad 81-0749 1
6 Sectional Indicator Screw Pack 82-5590 x finish 1
7 Sectional Indicator Mounting Plate 81-0750 1
8 Sectional Indicator Template Kit (not shown) 82-5601 1
* These parts are for 1-3/4"standard thickness doors. For other thicknesses, please contact factory.
Note:
Reference 8200 Series parts manual for all lock body parts.
4D

WARNING
This product can expose you to lead
which is known to the state of California
to cause cancer and birth defects or other
reproductive harm. For more information go
to www.P65warnings.ca.gov. A8257E 4/22