Assa Abloy Norton 5700 Series User manual

Copyright © 2010, 2014, 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9357-0140-020 Rev 3 09/19
5700 Series Power Operator Conversion
PUSH to PULL and PULL to PUSH Application
Patents: 5,881,497; 7,316,096; 7,484,333
5. Replace and tighten closer body screws.
6. Slide dip switch 1 on inverter from PUSH to PULL position.
Slide dip switch 2 from ON to OFF position. (Figure 4)
Note: Inverter Details located on page 3.
7. Turn on power to unit at On/Off switch and ip circuit
breaker to RESET position.
8. Immediately after activating unit, watch cam driver as
it rotates around. As soon as cam driver contacts pinion
extension, ip circuit breaker to OFF position. (Figure 3)
9. With door closed:
• Slide closed position magnet so it aligns with reed switch.
(Figure 5)
• Slide open position magnet so it is 180° from reed switch.
Slide magnet as needed to get proper door opening.
(Figure 5)
10. Flip circuit breaker to RESET position.
Pour la version francaise voir www.nortondoorcontrols.com.
READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
This product can expose you to lead which is known to the state of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65warnings.ca.gov.
WARNING
Changing Operator From Push Side Unit to Pull Side Unit
1. Verify unit is congured for a push side application:
• Latch and Sweep valves are toward conduit holes. (Figure 2)
• Cam driver of clutch mechanism is toward conduit holes.
(Figure 3)
2. Turn off power to unit at On/Off switch and ip circuit breaker
to OFF position. (Figure 1)
3. Using a Phillips head screwdriver, remove four (4) closer body
screws and slide closer body away from clutch assembly.
(Figure 1)
NOTE: DO NOT remove pinion extension when removing
closer body. (Figure 3)
4. Orient closer body with BC valve toward conduit holes and slide
onto backplate so that pinion shaft of closer is inserted into
pinion extension of clutch assembly. (Figure 2)
NOTE: Some rotational adjustment of pinion extension may
be required to allow reassembly of closer pinion shaft and
pinion extension. Pinion at should remain opposite of
backplate for proper reassembly. (Figure 3)
Figure 1
Figure 2 Figure 3
Wiring not shown
Figure 4
Figure 5

Copyright © 2010, 2014, 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9357-0140-020 Rev 3 09/19
2
5700 Series Power Operator - Conversion Instructions
Changing Operator From Pull Side Unit to Push Side Unit
Figure 6
Figure 7 Figure 8 Figure 9
Figure 10
5. Replace and tighten closer body screws.
6. Slide dip switch 1 on inverter from PULL to PUSH position.
Slide dip switch 2 from OFF to ON position. (Figure 9)
Note: Inverter Details located on page 3.
7. Turn on power to unit at On/Off switch and ip circuit
breaker to RESET position.
8. Immediately after activating unit, watch cam driver as
it rotates around. As soon as cam driver contacts pinion
extension, ip circuit breaker to OFF position. (Figure 8)
9. With door closed:
• Slide closed position magnet so it aligns with reed switch.
(Figure 10)
• Slide open position magnet so it is 180° from reed switch.
Slide magnet as needed to get proper door opening.
(Figure 10)
10. Flip circuit breaker to RESET position.
1. Verify unit is congured for a pull side application:
• BC valve is toward conduit holes. (Figure 7)
• Cam driver of clutch mechanism is away from conduit holes.
(Figure 8)
2. Turn off power to unit at On/Off switch and ip circuit breaker
to OFF position. (Figure 6)
3. Using a Phillips head screwdriver, remove four (4) closer body
screws and slide closer body away from clutch assembly.
(Figure 6)
NOTE: DO NOT remove pinion extension when removing
closer body. (Figure 8)
4. Orient closer body with latch and sweep valves toward conduit
holes and slide onto backplate so that pinion shaft of closer is
inserted into pinion extension of clutch assembly. (Figure 7)
NOTE: Some rotational adjustment of pinion extension may
be required to allow reassembly of closer pinion shaft and
pinion extension. Pinion at should remain opposite of
backplate for proper reassembly. (Figure 8)
Wiring not shown

Copyright © 2010, 2014, 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in
whole or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9357-0140-020 Rev 3 09/19 3
5700 Series Power Operator - Conversion Instructions

Norton is a brand associated with ASSA ABLOY Accessories and Door Controls Group, Inc., an ASSA ABLOY Group company.
Copyright © 2010, 2014, 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole
or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited. 80-9357-0140-020 Rev 3 09/19
Norton Technical Product Support:
Monroe, NC 28112 USA
Phone: [phone] ext: 6030
[e-mail]
nortondoorcontrols.com