Assa Abloy Norton 1600H Series User manual

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited. 80-9316-3532-020 Rev 1 05/19
Hold Open Arm Models
1600H
Non Handed Door Closer
Regular Arm
Top Jamb Mount
Parallel Arm
Ce produit peut vous exposer au plomb qui, dans l’état de la Californie,
est reconnu pour causer le cancer, des anomalies congénitales ou d’autres
problèmes de reproduction. Pour plus d’informations, visitez:
www.P65warnings.ca.gov.
This product can expose you to lead which is known to the state of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65warnings.ca.gov.
WARNING
Regular Arm Top Jamb Mount
*Included Components
Parallel Arm
Optional Plates Legacy Friction Hold Open Arm
Right Hand Door - RH
Left Hand Reverse - LHR
Left Hand Door - LH
Right Hand Reverse - RHR
Right Hand Door - RH
Left Hand Reverse - LHR
Left Hand Door - LH
Right Hand Reverse - RHR
Right Hand Door - RH
Left Hand Reverse - LHR
Left Hand Door - LH
Right Hand Reverse - RHR
Note: Legacy FHO arm has
installation orientation.
See 80-9300-0003-000 for details.
Tools Needed
TO DETERMINE
HAND OF
YOUR DOOR:
LEFT
HAND
DOOR
RIGHT
HAND
DOOR
Right Hand
Reverse
Left Hand
Reverse
To Determine Your Hand of Door: To Identify Your Model:
1-6 = 1601
3 = 1603BC
4 = 1604BC

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc.
All rights reserved. Reproduction in whole or in part without the express written
permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
280-9316-3532-020 Rev 1 05/19
Before You Begin
• For special applications, a separate door and frame
preparation template is packed with these instructions. Use
this instruction sheet for installation sequence and closer
adjustments only.
• Doors should be hung on ball bearing or anti-friction hinges.
• A separate door stop is recommended.
Mounting Hardware Door or Frame Drill
Closer, H/O Shoe or Optional PA Bracket:
1/4-14 x 1-1/2 Oval Flat Head Mach. Screw Wood 3/16" (4.76mm)
Closer, H/O Shoe or Optional PA Bracket:
1/4-20 x 3/4 Oval Flat Head Mach. Screw Metal Drill #7 (.201 dia. or 5.10mm)
Tap 1/4-20
H/O Shoe to Optional PA Bracket:
1/4-20 x 1/2 Oval Flat Head Mach. Screw
Closer:
Sleeve Nut and Bolt (SNB)
(optional)
Hollow Metal 9/32" (7.00mm) thru
3/8" (9.50mm) door face opposite to closer
Aluminum or Wood 3/8" (9.50mm) thru
Closer:
Thru Bolt and Grommet Nut (TBGN)
(optional)
All
9/32" (7.00mm) thru
3/8" (9.50mm) dia. x 3/8" (9.500mm) deep,
door face opposite to closer
• Always consult door/frame manufacturer for fastener
compatibility.
• Door and frame must be properly reinforced.
• Adjust closing time speed between 3 and 7 seconds from
90° to 0°.
• These door closers should NOT be installed on exposed side
(weather side) of exterior doors.
• Dimensions are given in inches (millimeters).
Closer Adjustments
Do not over tighten
cap or cover screws.
Pinion Cap or Cover
Regular Arm Top Jamb Mount Parallel Arm
ATTENTION:
An incorrectly installed or improperly adjusted door closer can
cause property damage or personal injury. These installation
instructions should be followed to avoid the possibility of
misapplication or misadjustment.
Latch Backcheck
Use provided hex wrench
to turn valves. NEVER
force valves out of closer.
NEVER completely close
backcheck valve.
Door must be open to
adjust spring closing
power. Refer to chart. Do
not use a power drill.
Warranty will be void.
Sweep

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc.
All rights reserved. Reproduction in whole or in part without the express written
permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
3
80-9316-3532-020 Rev 1 05/19
1. Prepare door and frame.
1600H Regular Arm Installation (Right Hand Shown)
Opening
To 100°
101° to 120°
*121° to 180°
7
(178)
6
(152)
3-1/2
(89)
Dimension "A"
*Door/Wall/Hardware/Jamb
conditions permitting
2. Mount closer to door. 3a. Remove dial from
Hold Open arm.
3
6
(152)
1-3/4
(44)
1-1/4
(32)
3/4
(19) 9-1/16
(230)
7/8
(22)
A
LS
3b. Install separate arms.
4. Connect arms, preload spring
and tighten set screw.
5. Set Hold Open.
1st
2nd 3rd
Keep door open in position
until dial screw secures dial.
1st
3rd 2nd
Rotate elbow until
Hold Open arm is
perpendicular to frame.
Rotating arm
preloads closer
spring power.
RH:
Clockwise
to tighten.
LH: Counter
clockwise to
tighten.
1st
3rd
2nd
You’ve installed the 1600H Hold Open Closer - Regular Arm.
🛑 Go to page 2 for closer adjustments and decorative cap or cover installation.
Dial DOWN
Left and Right Hand
RH and LH:
Position at at S

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc.
All rights reserved. Reproduction in whole or in part without the express written
permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
480-9316-3532-020 Rev 1 05/19
1600H Top Jamb Mount Installation (Right Hand Shown)
1. Prepare door and frame.
2. Mount closer to frame.
Opening
To 100°
101° to 120°
*121° to 180°
7-1/2
(191)
6
(152)
3-1/2
(89)
Dimension "A"
*Door/Wall/Hardware/Jamb
conditions permitting
9-1/16
(230) 3/4
(19)
1/2
(13)
6
(152)
1-1/2
(38)
1-3/4
(44)
C
L
A
Top of
Door
A longer connecting
rod is required
for reveals greater
than 3" (76)
Reveal
x4
3a. Remove dial from
Hold Open arm.
3b. Install separate arms.
5. Set Hold Open.
4. Connect arms, preload spring
and tighten set screw.
1st
2nd
3rd
Rotate elbow until
Hold Open arm is
perpendicular to frame.
Rotating arm
preloads closer
spring power.
Keep door open in position
until dial screw secures dial.
3rd
1st
3rd
1st
2nd
RH:
Clockwise
to tighten.
LH: Counter
clockwise to
tighten.
2nd
You’ve now installed the 1600H Hold Open Closer - Top Jamb Mount.
🛑 Go to page 2 for closer adjustments and decorative cap or cover installation.
Dial DOWN
Left and Right
Hand
RH and LH:
Position at at S

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc.
All rights reserved. Reproduction in whole or in part without the express written
permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
5
80-9316-3532-020 Rev 1 05/19
1600H Parallel Arm Installation (Right Hand Shown)
1. Prepare door and frame.
2. Close latch and sweep
valves.
4. Install soft plate and mount closer.
Door
Opening
To 100°
101° to 130°
*131° to 180°
A
9-1/4
(235)
7-3/4
(197)
5-3/4
(146)
B
7-5/8
(194)
6-1/8
(156)
4-1/8
(105)
C
8-5/8
(219)
7-1/8
(181)
5-1/8
(130)
*Door/Wall/Hardware/Jamb
conditions permitting
S
L
Holes for 9388
Plate only 1-1/2
(38)
7
(178) 4
(102)
2-1/8
(54) 3-1/4
(83)
1/2
(13)
3/4
(19)
9-1/16
(230) C
L
C
B
Top of
Door
Frame
2-3/4
(70) 3/8
(10)
1/2
(13)
7/16
(11)
2
(50)
A
LS
5. Install Hold Open arm to plate. 6. Place main arm on closer spindle and rotate.
Remove
Arm from
Spindle
R
o
t
a
t
e
x2
Dial DOWN
Left and Right Hand
3. Remove dial from
Hold Open arm.
x4
x4
IMPORTANT

Copyright ©, 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
www.nortondoorcontrols.com
Norton Technical Product Support:
Monroe, NC 28112 USA
Phone: [phone] ext: 6030
[e-mail]
80-9316-3532-020 Rev 1 05/19
1600H Parallel Arm Installation (Right Hand Shown) continued
7. Remove arm and attach as shown. 8. Open latch and sweep valves.
S
L
Do not completely
open valves. Valves
will leak.
Arm under tension.
Keep ngers away
from moving parts.
9. Connect arms, preload spring and
tighten set screw.
10. Set Hold Open.
1-1/2
(38)
1st
2nd
3rd
5th
1st
4th
By hand,
rotate arm
elbow to be
1-1/2" from
door face.
Keep door open in position
until dial screw secures dial.
3rd3rd
2nd
RH:
Clockwise
to tighten.
LH: Counter
clockwise to
tighten.
2nd
1st
You’ve now installed the 1600H Hold Open Closer - Parallel Arm.
🛑 Go to page 2 for closer adjustments and decorative cap or cover installation.
Rotating arm
preloads closer
spring power.
RH: Position at at R
LH: Position at at L
1st
2nd