Assa Abloy Norton 6011 Series User manual

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19
6011/6051 Series (Pull Side) Power Operator
Installation Instructions
Pour la version francaise voir www.nortondoorcontrols.com.
READ AND FOLLOW ALL INSTRUCTIONS. SAVE THESE INSTRUCTIONS.
6051 Pull Side (Handed) 1/8" to 3" (3mm to 76mm) reveal
All components above with 7250-1(R or L)
instead of 7210-1A arm
This product can expose you to lead which is known to the state of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65warnings.ca.gov.
WARNING
Tools Needed
6011 Pull Side Max 1/8" (3mm) reveal
1/4-20
#7
#2 and #3
10" or 12"
3/8
Punch
Set (Inch)
Supplied Fasteners
Union Assembly
(6001U)
Union Spacer
(6001US)
Cover
(6001COV)
Arm Assembly
(7210-1A)
End Cap - RH
(6001ENRH)
Closer Assembly
(7500LAP)
Operator LAP
(6011LAP)
Conduit Assembly
(6001CON)
Backplate (6001BP)
Power Module Sub-assembly
(6001PM)
Power Supply
(6000SUP)
Motor (not eld
replaceable)
Track Assembly
(7200-1T)
Inverter
(6000IN)
End Cap - LH
(6001ENLH)
Double Egress Arm
(7250-1R/7250-1L shown)

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19
2
6011/6051 Series (Pull Side) Power Operator
Certications and Standards
• ETL Certied: Operator conforms to ANSI/UL standard 325 for automatic closing doors and UL10C Positive Pressure
Fire Test for Door Assemblies.
• ANSI A156.19: These products are designed to conform to this specication “for power assist and low energy power
operated doors.” These products are designed to exceed all the requirements for “Low Energy Power Operated Door”.
• Americans with Disabilities Act (A.D.A.): These door operators can be installed and adjusted to conform with A.D.A.
regulations.
• ANSI A117.1: These door controls permit door assemblies to conform to the requirements of this specication “for
buildings and facilities - providing accessibility and usability for physically handicap people”.
Contents
Certications and Standards...............................................................................2
Product Safety Warnings ..................................................................................2
General Information.......................................................................................3
Before You Begin ..........................................................................................4
Mounting Hardware Chart.................................................................................4
Technical Data ............................................................................................4
Prepare Frame and Door ..................................................................................5
Install Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Install Track and Arm .....................................................................................10
Adjustments .............................................................................................11
Power Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Finalize Installation.......................................................................................13
General Electrical Information ............................................................................13
Wiring Options...........................................................................................14
Troubleshooting .........................................................................................25
6011/6051 Template . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
WARNING: To reduce risk of injury to person, use this operator only with Pedestrian Swing doors. FOR INDOOR USE ONLY
Product Safety Warnings
1. READ AND FOLLOW ALL INSTRUCTIONS.
2. Install only on a properly operating and balanced door.
A door that is operating improperly could cause severe
injury. Have qualied service personnel make repairs to any
hardware before installing the operator.
3. Remove, or make inoperative, all locks (unless mechanically
and/or electrically interlocked to the power unit) that are
connected to the door before installing the operator.
4. Do not connect the door operator to the source power
until instructed to do so.
5. Never let children operate or play with door controls. Keep
remote control (when provided) away from children.
6. Personnel should keep away from a moving door in
motion.
7. Test door’s features at least once a month. After
adjusting either force or limit of travel, retest door
operator’s features. Failure to adjust operator
properly may cause severe injury or death.
8. KEEP DOOR PROPERLY OPERATING. An improperly
operating door could cause severe injury or death.
9. SAVE THESE INSTRUCTIONS.

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19 3
6011/6051 Series (Pull Side) Power Operator
Operation:
Your Low Energy Operator can be congured in three variations to meet the standards:
1. Push plates, Wave-to-open switches, etc. are available to activate the operator.
2. Push & Go can be enabled. In this mode, your door is pushed (or pulled) slowly 15° manually, and then
automatically opens to full open position.
3. Door can be used as a manual door. The door will work and act like a standard door closer, with or without power,
when pushed or pulled open manually. If Push & Go is enabled and door is opened quickly, door will function as a
manual door (energy save feature). Push plates are still active.
If desired, overhead presence devices can be provided for an extra level of protection. Consult local authority having
jurisdiction. These are not required by current ANSI/BHMA A156.19 standards.
Opening:
When an opening signal is received by the control unit, the door opens to the fully open position. The open position is
held by the motor and is adjustable from 0 to 30 seconds. If the door is obstructed while opening, the door will stop; the
operator will sense obstruction (obstruction time is adjustable from 0 to 5 seconds) and the door will close.
NOTE: Door must be visible by person operating activation switch(es). Auxiliary door stop (by others) required.
Closing:
When the hold open time has elapsed, the door closer will close the door automatically. The door will slow to low speed
at latch before it reaches the fully closed position. The door is kept closed by spring force of the closer. If the door is
obstructed while closing, the door will stop against the obstruction; the operator will sense obstruction and reopen to
fully open position after obstruction time has been reached. Once the hold open time has elapsed a second time, the door
closer will close the door automatically. If the door is obstructed during this second closing cycle, the door will stop and
rest against the obstruction using only the force of the closer spring. To reset, allow door to fully close and re-activate push
plates to test operation.
Innite Hold Open:
An optional feature to be used if door is desired to be held open for more than 30 seconds.
Set selector mode switch on underside of union assembly to hold open. Door will immediately begin to open to the
fully open position. Once door is fully open, brake on end of motor energizes holding door in open position. To release
from hold open, if door is set up for executive operation (see page 18 or 20 for executive wiring instructions), door can
be closed with activation device. A pull on the door will also allow the unit to be taken out of hold open. Once door has
closed, the door will reopen to fully open position unless activation device is pressed or selector mode switch is changed
from hold open position.
NOTE: Door must be visible by person operating activation switch(es). Auxiliary door stop (by others) required.
WARNING: Make sure (120V, 60Hz) input
power is turned OFF at facility’s main circuit
breaker before proceeding with installation
General Information

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19
4
6011/6051 Series (Pull Side) Power Operator
Technical Data
Input power: 120VAC, 60Hz
Power consumption: .9 amps
Circuit breaker: 3 amps
Power supply: 24 V DC, max. 2.2 amp.
Door width: 36" - 48" (91-122 cm)
Door weight: 100-250 lb. (43-113 kg)
Door opening angle: up to 110° with reveal of 3" (7.6 cm) max
Hold open time: 0-30 seconds (A.D.A. 5 seconds min.)
Indenite for optional Innite Hold Open
Notes:
• Permanent wiring is to be implemented as
required by local codes.
• Activation devices: push plates, access control,
mats, touchless wall switches, etc.
• Maximum wire size is:
12AWG at terminals LINE and NEUTRAL
(120VAC; 60Hz) on Power Input Terminal
mounted on inside of end cap.
14AWG at all other terminals
• Rate of operation shall not exceed 300 cycles of
opening and closing per hour.
Before You Begin
• All dimensions are given in inches.
DO NOT scale drawings.
• Thickness recommended for reinforcements
in hollow metal doors and frames is charted.
• This template information based upon use of
5" maximum width butt hinges.
• Maximum frame reveal is 1/8" for 6011 units
and 1/8" up to 3" maximum for 6051 units.
• Before beginning the installation, verify that
the door frame is properly reinforced and is
well anchored in the wall. Frame header must
be straight - without warp or bow.
• Unreinforced hollow metal frames and
aluminum frames should be prepared and
tted with 1/4-20 blind rivet nuts, furnished
by others.
• Concealed electrical conduit and concealed
switch or sensor wires should be pulled to
the frame before proceeding.
1/8"
(3)
Door
Frame
Hollow Metal Door Frame Reinforcing
Frame Material Reinforcing
Recommended Min. Required
12 Ga.
.105
(2.66)
12 Ga.
.105
(2.66)
18 Ga.
.048
(1.21)
14 Ga.
.075
(1.90)
10 Ga.
.134
(3.41)
12 Ga.
.105
(2.66)
16 Ga.
.060
(1.52)
10 Ga.
.134
(3.41)
12 Ga.
.105
(2.66)
18 Ga.
.048
(1.21)
8 Ga.
.164
(4.18)
10 Ga.
.134
(3.41)
Fasteners for Frame:
• 1/4-20 Machine screws for
hollow metal and aluminum.
• No. 14 x 2-3/4" (70mm) long
sheet metal screws for wood. Templating based on 1/8" gap
between door and frame.
Mounting Hardware Door or Frame Drill
Backplate:
14 x 1-1/2 Flat Head Self Drilling Screw Wood 3/16" (4.76mm)
Backplate:
1/4-20 x 1 Flat Head Machine Screw Metal Drill #7 (.201 dia. or 5.10mm)
Tap 1/4-20
Backplate:
1/4-20 x 5/8 Flat Head Machine Screw
Track:
Sex Nut and Bolt (SNB)
(optional)
Hollow Metal 9/32" (7.00mm) thru
3/8" (9.50mm) door face opposite to closer
Aluminum or Wood 3/8" (9.50mm) thru

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19 5
6011/6051 Series (Pull Side) Power Operator
33-7/8
(860)
Prepare Frame and Door
Figure 1
Pull Side
Push Side
Left Hand
PULL
Right Hand
PULL
Become familiar with operator components and fasteners. It is recommended that components remain in box
until installed. Verify there is minimum ceiling clearance for operator installation before proceeding. (Figure 1)
A. Prepare frame.
1. Determine if push or pull and if left hand or right
hand installation. (Figure 2)
NOTE: These instructions are for PULL only.
See 80-9360-1027-020 instructions for
6021/6031 or 80-9360-1028-020 instructions
for 6061/6071 Push installation.
2. Frame header MUST be at / without twists.
Backplate can be used as reference.
NOTE: If frame is not at or is twisted, an
additional steel back plate or shimming is
required. Failure to mount unit properly can
result in improper function of operator or
inability to snap on cover.
3. Using template on page 26, prepare mounting
holes for screws. (Figure 3)
a. Mark 5-5/8" from centerline of hinge toward
latch edge of door and 1" up from underside
of frame rabbet.
b. Mark 30-5/8" from centerline of hinge toward
latch edge of door and 1" up from underside
of frame rabbet.
c. Drill/tap two (2) 1/4-20 holes for steel frame
or two (2) #14 holes for wood frame at
marked locations.
4. Prepare holes for concealed mounted conduit
(if applicable).
a. Mark frame 33-7/8" from centerline of hinge
toward latch edge of door and 1-3/8" up from
underside of frame rabbet.
b. Mark frame 1-1/4" from previous mark toward
latch edge of door and 1-3/8" up from
underside of frame rabbet.
c. Drill two (2) 7/8" diameter holes in frame at
marked locations.
5. Using supplied backplate screw pack, insert
screws into prepared mounting holes.
For Metal Frame: Use two (2) 1/4-20 x 1" at
head machine screws.
For Wood Frame: Use two (2) #14 x 1-1/2” at
head self-drilling screws.
NOTE: Do not tighten mounting screws at
this time. Leave 5/16" minimum (thickness of
backplate) between frame face and back of
screw head.
Left Hand Shown
OR
Figure 2
Figure 3

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19
6
6011/6051 Series (Pull Side) Power Operator
B. Mount Backplate.
1. Slide backplate over mounting screws.
(Figure 4)
NOTE: Backplate conduit slots are ALWAYS
toward latch edge of frame for proper
orientation.
2. Use level in backplate to align and tighten
mounting screws.
3. Using countersunk holes in backplate as a
template, drill/tap remaining six (6) mounting
holes: 1/4-20 for steel frame or
#14 for wood frame. (Figure 5)
Remaining Mounting Holes
C. Prepare door for Track.
1. Using template on page 26, locate and
prepare track holes in door. (Figure 6)
2. Drill 3/8" (9.5mm) through (3 places)
for sex bolts.
Left Hand Shown
Conduit Slot
Built-in Level
Prepare Frame and Door
Figure 4
Figure 5
Figure 6
ADimension Operator Model
1-1/16" (27mm) 6011
1-11/16" (43mm) 6051
C
L
Hinge or Pivot
Frame
Rabbet
Frame
Stop/Soffit
A
11"
(279)
22"
(559)
3/8 Dia.
Sex Nuts
(3 Places) 5-3/8"
(137)

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19 7
6011/6051 Series (Pull Side) Power Operator
Install Operator
A. Secure Backplate.
1. Secure backplate to frame using six (6):
1/4-20 x 5/8" machine screws or
1/4 x 1-1/2" self-drilling screws. (Figure 7)
NOTE: It is important to properly secure
top edge of backplate. Use of blocking
(supplied by others) or shims (provided) to
ll gap between backplate and wall above
header is HIGHLY recommended. Material
must comply with local codes. Failure to
properly secure top of backplate could result
in operator being allowed to ‘rock’ during
operation. This could result in damage to
operator and diminish operator function.
(Figure 7)
B. Install End Caps.
1. Secure end caps to each end of backplate using
four (4) (two each) #8-32 x 5/16" Phillips pan
head screws. (Figure 8)
NOTE: Orient end caps so that text on labels is
legible when observed from ground.
OR
Blocking
Figure 7
Figure 8

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19
8
6011/6051 Series (Pull Side) Power Operator
C. Install Operator LAP.
NOTE: Backplate is printed with text to assist
installation.
1. With backplate mounted to frame, use text to
locate holes along bottom of backplate that
correspond to your specic closer installation.
(Figure 9)
2. Insert two (2) 1/4-20 x 1/2" Phillips pan head
screws into appropriate engraved locations
leaving a 5/16" minimum gap between
backplate and underside of screw head.
3. Orienting LAP so spring tube of closer is
pointed toward hinge edge of frame, slide LAP
over two (2) screws and tighten. (Figure 10)
4. Using six (6) 1/4-20 x 1/2" Phillips head screws,
secure LAP to backplate. (Figure 11)
NOTE: Holes in LAP align with threaded holes
in backplate.
NOTE: Screws to be torqued to 80 in-lb
minimum.
6060/6070 @ 85DEG
6060/6070 @90DEG
6060/6070 @ 95DEG
6060/6070 @ 100DEG
6020 & 6060/6070 @ 105DEG
6060/6070 @ 110DEG
6010/6050 & 6030
Operator LAP
Mounting Screws
D. Install Conduit Assembly and wire to building.
1. Orient conduit assembly so two (2) conduit
holes are at bottom and text on wire input label
is legible. (Figure 12)
2. Secure assembly to backplate using four (4)
#8-32 x 5/16" Phillips head screws. (Figure 12)
WARNING: BUILDING POWER MUST BE OFF
BEFORE PROCEEDING!
3. Secure conduits to conduit assembly (surface or
concealed conduit). (Figure 13)
4. Wire building 120VAC to conduit assembly –
LINE, NEUTRAL, and GROUND. (See page 13 for
General Electrical Information.)
5. Wire 24VDC for accessories to conduit assembly
24VDC + / - as required. (See page 13 for General
Electrical Information.)
WARNING: DO NOT TURN ON BUILDING POWER
UNTIL DIRECTED TO DO SO! RISK OF INJURY OR
DEATH!
Install Operator
Figure 9
Figure 10
Remaining LAP Mounting Screws
Figure 11
Figure 12
Figure 13

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19 9
6011/6051 Series (Pull Side) Power Operator
F. Connect Operator LAP and Power Module Sub-assembly.
1. Attach 10-pin black connectors between
operator LAP and power module sub-assembly.
(Figure 15)
2. Attach 3-pin white connectors between operator
LAP and power module sub-assembly.
(Figure 15)
NOTE: Connectors are keyed and only attach
one way.
G. Install Union Assembly and Union Spacer.
1. Orient union assembly so access door
covering selector mode switch faces oor.
(Figure 16)
2. Snap union spacer onto union assembly
opposite end cap and secure with two (2)
#6-32 x 1/4" Phillips pan head screws.
(Figure 17)
3. Secure union assembly to backplate using
two (2) #8-32 x 5/16" Phillips pan head
screws. (Figure 17)
4. Connect 4-pin black square connector from
power module sub-assembly to 4-pin black
connector from union assembly. (Figure 17)
NOTE: Connectors are keyed and only
assembly one way.
Install Operator
E. Install Power Module Sub-assembly.
1. Using three (3) #8-32 x 5/16" Phillips screws,
secure power module sub-assembly to backplate
at location marked on backplate. (Figure 14)
NOTE: Orient assembly so LCD screen on
inverter is toward closer assembly. (Figure 14)
2. Attach 4-pin white rectangular connectors
between power module sub-assembly and
conduit assembly. (Figure 14)
NOTE: Connectors are keyed and only attach
one way.
Figure 14
Figure 15
Figure 17
Selector
Mode
Switch
Figure 16

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19
10
6011/6051 Series (Pull Side) Power Operator
B. Install Arm Assembly.
1. Open door.
2. Using an adjustable wrench, rotate
top pinion 45 degrees toward door
hinge. You will feel resistance from
spring. (Figure 20)
3. While holding pinion at 45 degrees,
slide arm on bottom pinion parallel
to frame as shown. (Figure 20)
NOTE: Pinion at should be aligned
as shown. (Figure 21)
4. Secure arm to pinion with 1/4-20 x
1/2" screw and countersunk patch
washer. (Figure 20)
5. Insert stud on arm into slider in track
by pressing clip on backside of slider
onto stud. (Figure 22)
6. To adjust track stop:
• Use allen wrench to loosen set
screw in bumper stop.
• Open door to full open position.
• Slide bumper stop until it just
touches end of slider.
• Tighten set screw in bumper stop
so bumper will stay in position.
(Figure 23)
A. Mount Track to door.
1. Using previously prepared holes in
door, install three (3) 1/4-20 x 1-5/8"
screws through track and into sex
bolts. (Figure 18)
NOTE: (Figure 19)
• Opening of track is toward top
of door.
• Adjustable bumper stop is toward
hinge edge of door.
Install Track and Arm
Set Screw
Bumper Stop
Slide
Assembly
Arm Stud
B
A
Adjustable Bumper Stop
Track Opening
Figure 18
Figure 19
Figure 20
Figure 21
Figure 22
Figure 23

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19 11
6011/6051 Series (Pull Side) Power Operator
B. Adjust spring force.
NOTE:
• The amount of effort to manually open or
close a door is called force and is controlled by
the operator’s closer spring.
• Make necessary mechanical adjustments
described in “A” above.
• A closer set to ADA required 5 lbs opening
force may not be strong enough to close door
due to latching hardware, air pressure, or
frame issues.
1. Using 11/16" wrench, turn nut in end of closer
body tube to desired force.
(Figure 25)
NOTE: If spring adjustment nut is too close
to end cap and wrench will not reach nut,
remove Torx screw in end cap access door and
slide door open. When nished, slide access
door closed and reinsert #6 Torx at head
screw to secure door. (Figure 25)
Adjustments
A. Adjust mechanical closer features.
NOTE:
• Make necessary mechanical adjustments so
unit functions as a standard surface mounted
door closer before adjusting spring force,
applying power, adding accessories or making
electrical/programming adjustments.
• Valve location S/D is not adjustable.
• Chain protection plate cutouts allow access to
valves. Use hex wrench to make adjustments.
(Figure 24)
Do not remove valves from closer.
Hydraulic oil will escape.
1. Closing Speed Controls (Figure 24)
• Valve “S” controls Sweep Range from
full open to 10°.
• Valve “L” controls Latch Range from
10° to closed.
2. Opening Cycle (Figure 24)
• Valve “B” controls strength of cushioning in
Backcheck Range.
NOTE: NEVER close Backcheck valve
completely – it is not to provide a positive
stop.
• Valve “P” adjusts angle that backcheck is
felt in open cycle. Factory preset is typically
acceptable.
Figure 24 View from ceiling looking down
Figure 25
Chain Protection Plate

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19
12
6011/6051 Series (Pull Side) Power Operator
You’ve now installed the 6011 or 6051 PULL SIDE Low Energy Operator.
Continue with Electrical Instructions to customize the installation.
Power Operator
1. Open door on union assembly and place selector mode switch
in ‘OFF’ position. (Figure 26)
2. Turn On/Off switch to ‘OFF’ position on conduit assembly.
(Figure 27)
3. Turn on building power.
4. Turn On/Off switch to ‘ON’ position on conduit assembly.
See page 15 for controller adjustment options.
• To scroll through menu items, push up or down on joystick.
(Figure 27)
• To change setting of a menu item, when cursor is on that
item, push joystick right to increase or left to decrease value.
NOTE: Values will auto-save 3 seconds after adjustments.
5. Set ‘HOME’ procedure for door.
• With door closed and selector mode switch of union
assembly in “OFF” position, use joystick to scroll down menu
on LCD screen to “Home”.
• Push in on joystick to activate menu feature. Display changes
to “Set Close Limit”.
• Push in on joystick again, while door is still closed, to set
Home or closed position (Figure 28). Display changes to “Set
Open Limit”.
• Open door to desired open position (Figure 28) and push in
on joystick again. Display changes to “Closing to Home”.
• Allow door to fully close again (Figure 28). Display changes to
“Home”.
NOTE: Values will auto-save.
6. Make necessary adjustments to inverter and add required
accessories.
7. Place selector mode switch of union assembly in ‘ON’ position
for activation by push plate, RF button, or other activation
devices. Place switch in ‘H/O’ for continuous hold open.
(Figure 26) Secure union assembly door with #4 Phillips screw
when nished.
Figure 26
Union Assembly and Spacer not shown
Figure 27
WARNING: Door may begin to move
immediately when power is applied to unit.
An open union assembly door has potential to
pinch ngers if hand is not withdrawn quickly
when switching on power.
Selector
Mode
Switch
Figure 28
WARNING: Door may begin to move immediately when
selector mode switch is changed. An open union assembly
door has potential to pinch ngers if hand is not withdrawn
quickly when adjusting switch.

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19 13
6011/6051 Series (Pull Side) Power Operator
Attach Cover to nalize installation
1. Align cut-outs in cover to pinion shafts.
(Figure 29)
2. Slide cover onto unit using end cap and union
spacer as guides.
NOTE: Verify all wiring and sheet metal
guards are inside cover.
3. Snap cover securely to backplate. Pull on
cover to verify it is secure.
NOTE: If cover will not securely snap onto
backplate, verify backplate is not warped or
twisted. Additional support or shimming may
be required. See Sections A & B under Prepare
Frame and Door.
WARNING: Make sure no wiring is loose or can be
caught by cover when it is snapped into place.
Figure 29
General Electrical Information
• Power inputs at power input connection and
power output contacts must be made with
copper wire only.
• Maximum wire size:
12 AWG at power input connection
14 AWG at all other terminals.
• Power input at terminals LINE and NEUTRAL
must be 120VAC at 60 Hz (+10%, -15%).
• Maximum current draw from auxiliary
devices is 1.3 amps.
• All wiring and connections use standard
wiring practice conforming with local wiring
codes.
• Labeled re or smoke barrier door
assemblies require 120VAC 60Hz power
input be supplied through normally closed
alarm contacts of the alarm system / alarm
panel.
Pinion Shaft Cut-out

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19
14
6011/6051 Series (Pull Side) Power Operator
Factory Pre-Wiring of Connections and Incoming Wiring
Controller Error Codes
Error Code Description
Short Circuit A short was sensed on the motor outputs
Temperature Trip Power module reached 200°F or greater (too much load in too hot ambient
condition)
Over Voltage Line Voltage has reached 145VAC or greater
Under Voltage Line Voltage has dropped below 80VAC
Aux 1 Stuck Activation device connected to Aux 1 is sending constant signal
Aux 2 Stuck Activation device connected to Aux 2 is sending constant signal
Aux 3 Stuck Activation device connected to Aux 3 is sending constant signal
Comm Error No communication between top and bottom controller boards. Boards not
functioning properly
Presence Detect Device connected to Presence Detect and was activated
Drive Disabled Selector mode switch on end cap closest to latch is in “OFF” position
To connect wiring:
For Incoming 120VAC and 24VDC for accessories
1. For 20 - 10 AWG wire
2. Strip end of wire 1/4 inch
3. Insert wire into appropriate position as shown
and use at head screw driver to secure
For Low Voltage / Dry Contacts on Inverter
1. For 24 - 16AWG wire
2. Strip end of wire 3/8 inch
3. Use at blade screw driver to push down on
white button above desired location, insert
wire, release button. Pull on wire to conrm
installed properly.

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19 15
6011/6051 Series (Pull Side) Power Operator
Controller Interface Description
Screen 1 Adjustments Default Description
Mount: Push or Pull Push Side of opening operator is mounted on
Hold Open: 0 - 30 sec in 1 sec increments 4s Amount of time door will stay in full open position after an activation
Open Delay
(previously
Start Delay):
0 - 10 sec in 1 sec increments 0s Time before operator begins to open door. This is to allow accessories time to
function and not hinder the opening of the door.
Latch Rtrct: OFF, 3 - 45 sec in 5 sec
increments OFF Amount of time power is supplied to a latch retraction device.
Home: see Setting Open Position - Used to set the Home position and the Fully Open position of the door.
Vestibule: OFF, 5 - 30 sec in 5 sec
increments OFF Amount of delay for opening 2nd vestibule door
Push: OFF or PushNGo OFF Turn on or off Push N Go feature. If On, a slight push or pull of the door starts it
automatically opening.
Open Speed: 0 - 100% in 1% increments 120 How fast the door opens to the full open position.
Close Speed: 0 - 100% in 1% increments 80
How fast the motor returns to the home position. As Latch and Sweep on the
closer are adjusted, adjustments may be needed for Close Speed to assure
closer is not trying to backdrive the motor.
Errors: not adjustable - Error code seen by controller. See Page 14 for Controller Error Codes.
Screen 2 Adjustments Default Description
Door Feedback: not adjustable -General feedback. Includes Door State, Door Position, Motor Position, Open
Limit, Close Limit.
Drive Feedback: not adjustable -General feedback. Includes Bus Voltage, Bus Current, Frequency.
Usage: not adjustable -General feedback. Includes Open Time, Close Time, Days, Cycles, Firmware Rev.
Single: not functional - future Single not functional - for future
MastStopOffset: not functional - future 180 not functional - for future
PDET Option: On, Off Off On or Off for 585 Presence Detector
DT:
Standard, SS1:Stall,
SS1:Return Open, SS1:Stall /
Open
Stnd
Standard is Door Toggle. SS1 is for use of a Closing side door presence
detector. SS1:Stall - door stalls when obstruction is detected; SS1:Return Open
- door reopens when obstruction is detected; SS1:Stall/Open - door stalls
when obstruction is detected and then reopens when obstruction is removed.
A2:
Standard, SS2:Stall,
SS2:Return Home, SS2:Stall /
Home
Stnd
Standard is Activation mode - just like A1 activation. SS2 is for use of an
Opening side door presence detector. SS2:Stall - door stalls when obstruction
is detected; SS2:Return Home - door closes to home when obstruction is
detected; SS2:Stall/Home - door stalls when obstruction is detected and then
returns home when obstruction is removed.
Rly2: Alarm, Activation, On Opened,
On Closed Alarm
How Relay 2 is used: Alarm - used with above Alarm Delay; Activation - acts as
an additional NO/NC contact; On Opened - relay trips (closed contacts) when
door is in opened position; On Closed - relay trips (closed contacts) when
door reaches the fully closed position.
Alarm Delay: OFF, 30 sec, 60 sec OFF Used only for alarm accessories
Slow Speed: 0 - 100% in 1% increments 55 Speed up or slow down door during last few degrees of opening.
Hold Speed: 0 - 100% in 1% increments 55 Increase or decrease hold open force (when in “ON” position only, not “H/O”)
to compensate for spring force, wind conditions, etc.
Obst Delay: 0 - 5 sec in 1 sec increments 3s
Obstruction Delay: the amount of time the operator will push against an
obstruction before closing if during an opening cycle or reopening and trying
to close again if during a clocking cycle.

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19
16
6011/6051 Series (Pull Side) Power Operator
Basic Wiring Diagram Using Factory Pre-Wired Connection
Standard Function with Switches
• Doors are normally closed.
• Activating either switch will open both
doors. Door will close after hold open time
delay has expired.
• Doors are normally closed and latched.
• Activating switch will unlock electric strike
and door will automatically open. Door will
close after hold open time delay has expired.
• Door will remain locked during power failure.
Fail Secure Electric Strike 24VDC Wiring

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19 17
6011/6051 Series (Pull Side) Power Operator
Fail Safe Electric Strike or Electromagnetic Lock 24VDC Wiring
24VDC Electric Exit Device Wiring
Factory Pre-Wiring In Illustration Is For This Functionality
Change Factory Pre-Wiring to Illustration Below (move NO to NC)
• Doors are normally closed and latched.
• Activating switch will energize exit device
and door will automatically open. Exit device
will stay energized based on Latch Rtrct
setting. Door will close after hold open time
delay has expired.
• Current draw at Power Outputs not to exceed
1.3 amps.
• Doors are normally closed and latched.
• Activating switch will unlock electric strike or
mag lock and door will automatically open. Door
will close after hold open time delay has expired.
• Door will remain unlocked during power failure.
• Current draw at Power Outputs not to exceed
1.3 amps.

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19
18
6011/6051 Series (Pull Side) Power Operator
Electric Dogging Exit Device Wiring
Hard Wired Executive Function Wiring
Factory Pre-Wiring Not Required to Change
• Doors are normally closed.
• Activating switch will open door.
• Door will remain in indenite hold open until activating
switch is activated a second time causing door to close.
Change Factory Pre-Wiring to Illustration Below (move NO to +24)
• Doors are normally closed and latched.
• Turning key switch ON will apply power to exit device.
• First depression on device touchpad will electrically dog
device for push/pull operation.
• Door will now open automatically when wall switch is
depressed.
• Device will re-latch during a power failure or when key
switch is turned off.
• Exit device allows egress at all times. Exit device allows
egress during power failures.
• Current draw at Power Outputs not to exceed 1.3 amps.

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19 19
6011/6051 Series (Pull Side) Power Operator
Electric Latch Retraction Exit Device Wiring
Electric Latch Retraction Exit Device Wiring for Smoke Ventilation - Blow Open Function
Change Factory Pre-Wiring to Illustration Below (move GND to COM)
Change Factory Pre-Wiring to Illustration Below (move GND to COM)
• Doors are normally closed and latched.
• Activating switch will retract exit device latch bolt and
operator will open door.
• Door will close after hold open time delay has elapsed.
• Exit device allows egress at all times. Exit device allows
egress during power failure.
• Contact Tech Support for other devices or manufacturer’s
instructions.
NOTE: This application must be approved by local (AHJ) authority
having jurisdiction.
• Doors are normally closed and latched.
• Fire Alarm activation will retract exit device latch bolt and door
operator will open door.
• Door will remain open until the Fire Alarm System has been reset.
• Door Operator’s main power input must be wired into building’s
back-up power system.
• Exit device allows egress at all times. Exit device allows egress
during power failure.

Copyright © 2019, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or
in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.
80-9360-1026-020 Rev 4 11/19
20
6011/6051 Series (Pull Side) Power Operator
Radio Frequency Standard Function Wiring
Radio Frequency Executive Function Wiring
If Installing in the Field, change Factory Pre-Wiring to Illustration Below (move NO to +24)
If Installing in the Field, change Factory Pre-Wiring to Illustration Below (move NO to +24)
• Doors are normally closed.
• Activating wireless switch or hand held
wireless transmitter will open door.
• Door will close after hold open time
delay has elapsed.
• Current draw at Power Outputs not to
exceed 1.3 amps.
• Doors are normally closed and latched.
• Activating wireless switch or hand held
wireless transmitter will open door.
• Door will remain in indenite hold
open until wireless switch or hand held
transmitter is activated a second time
causing door to close.
• Current draw at Power Outputs not to
exceed 1.3 amps.