Assa Abloy SARGENT Profile v.G1.5/LK User manual

A7855C
02/14
Copyright 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written
permission of Sargent Manufacturing Company is prohibited.
Profile
& LK Mortise Lock
Installation Instructions
v.G1.5

Warning
1-800-810-WIRE • www.sargentlock.com • A7885C
Copyright © 2011, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
11/11/11
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation.
This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced TV technician for help
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme avec la norme NMB-003 du Canada.
Changes or modifications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
To comply with “Fire Listed” doors, the batteries must be replaced with alkaline batteries only.
Do not install batteries if controller is powered by external power supply.
Warning SARGENT Mfg. Co. locksets utilizing a door position switch (DPS)
are not rated for, or intended for use in life safety applications.
!
1
1
2
3
4
5
6
7
Table of Contents
Warning ...................................................................................2
General Description.................................................................3
Specifications ..........................................................................3
Features ...................................................................................3
Parts Breakdown .....................................................................4
Installation Instructions ..........................................................6
RF Technology Lock...............................................................15
Hardwire Wiring Options .......................................................16
Operational Check .................................................................21
!
8
9

01/31/14
1-800-810-WIRE • www.sargentlock.com • A7855C 3
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Profile Series v.G1.5/LK Mortise Lock
Features
General Description
The SARGENT Profile v.G1.5/LK Mortise Lock is designed for areas which require stand alone authorized entry.
It is a self-contained microprocessor-controlled keypad with non-volatile memory. The keypad holds a total of
100 (LK)/2000 (G1-LU, G1-PK, G1-PA, G1-TU, G1-TP, G1-TA) different user codes. User codes 01 and 02 are
utilized for Master and Supervisory Codes, respectively. SARGENT mortise locks are designed with quality
components to provide high security, performance and durability.
• The Profile v.G1.5 Series provides enhanced software and hardware features.
• New v.G1.5 controllers replace v.G1 controllers. Product is still ordered as “G1-” prefix.
Controllers are labeled “G1.5”.
• This product is operated by six (6) “AA” alkaline batteries.
Specifications
• Latch - Stainless steel
• Deadbolt - Stainless steel
• Guardbolt - Stainless steel, non handed
• Handed - Easily field reversible without
disassembling the lock body
• Case - 12 gauge heavy duty wrought steel
3
4
2
• Outside lever controlled by any combination
of keypad, proximity or RF technology
• Inside lever retracts latch and deadbolt
• Locks furnished for 1-3/4” doors. Can be furnished
for other door sizes upon request.(Consult factory)
• U.L. Listed
• RF Fob and Proximity Card, Tag, and
Fob are optional
• Operates utilizing any one to six digit code
• Digits may be repeated and codes may
start with zero
• Cylinder override
• Entry of three wrong User Codes disables all
codes for ten seconds. Yellow LED on solid
• Piezo horn can be heard with each keystroke
or turned off by Master or Supervisory Code
• Last 15 transactions can be output to portable
print via infrared link (LK Only)
• Last 2000 (Except LK) transactions can be
output to PC via DTD/SoloPlus™ Software
• Non-volatile memory
• Motor driven, battery operated
• Battery operated with 6 “AA” Alkaline
• Low battery alert: 4 chirps after code entry
• External remote “request to enter”
• Master, Emergency or Supervisory code will
unlock door when low battery has expired
• 100 (LK) or 2000 (G1-LU, G1-PK, G1-PA,
G1-TU, G1-TP, G1-TA) users
• Programming done at keypad or with a DTD
(Data Transfer Device) using SoloPlus™
software and a Laptop/PC (G1-TA and
G1-TP require software)
SoloPlus™ works with PalmPilot; SofLink™
Plus software not supported with DTD.

4 1-800-810-WIRE • www.sargentlock.com • A7855C
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
01/31/14
Profile Series v.G1.5/LK Mortise Lock
5Parts Breakdown
35
2800-810-WIRE (9473) •www.sargentlock.com•A7855B
Prole Series v.G1.5
05/04/09 A7855:B
11
11
27/28
29
5
4
3
7
2
16
17
15
14
89
15
31
21
22 20
20
18/19
25
23
24
26
21
22
26
16
1
17
30
13
13
12
24
33
5Parts Breakdown
4
17
30
1
11
517
16
20 17 20
11
2
15
14
31
22
21
20
18 19
20
23
24 25
26
89
26
21
13
13
24
16
12
22
3
34
Outside
Inside
32

01/31/14
1-800-810-WIRE • www.sargentlock.com • A7855C 5
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Profile Series v.G1.5/LK Mortise Lock
ITEM PART No. DESCRIPTION REQ’D
1 82-4190 Outside Escutcheon with Cylinder Hole and Key Pad, or Key
Pad/Prox (G1-LU, G1-PK, G1-TU, G1-TP)
1
82-4191 Outside Escutcheon without Cylinder Hole and Key Pad or Key
Pad/Prox (G1-LU, G1-PK, G1-TU, G1-TP)
1
82-4192 Outside Escutcheon with Cylinder Hole and Prox Only (G1-PA,
G1-TA)
1
82-4193 Outside Escutcheon without Cylinder Hole and Prox Only (G1-
PA, G1-TA)
1
82-0493 Outside Escutcheon Housing Only without Cylinder Hole 1
82-0495 Outside Escutcheon Housing Only with Cylinder Hole 1
52-2432 Keypad/Proximity Bezel Assembly w/ Harness (LK) 1
52-2706 Proximity Only Bezel Assembly with Harness (G1-PA, G1-TA) 1
52-2704 Key Pad/Proximity Bezel Assembly with Harness (G1-LU, G1-PK,
G1-TU, G1-TP)
1
2 82-3837 Inside Escutcheon with Thumb Turn and 100 User Controller (LK) 1
82-3838 Inside Escutcheon without Thumb Turn and 100 User Controller
(LK)
1
82-4182 Inside Escutcheon with Thumb Turn and 2000 User Controller
(G1-LU)
1
82-4183 Inside Escutcheon without Thumb Turn and 2000 User Controller
(G1-LU)
1
82-4184 Inside Escutcheon with Thumb Turn Prox/Key Pad Controller
(G1-PA, G1-PK)
1
82-4185 Inside Escutcheon without Thumb Turn Prox/Key Pad Cont.
(G1-PA, G1-PK)
1
82-4186 Inside Escutcheon with Thumb Turn & 2000 User Controller with
RF Technology (G1-TU)
1
82-4187 Inside Escutcheon without Thumb Turn & 2000 User Controller
with RF Technology (G1-TU)
1
82-4188 Inside Escutcheon with Thumb Turn & Keypad/Prox or Prox Only
Controller (G1-TA, G1-TP)
1
82-4189 Inside Escutcheon without Thumb Turn & Keypad Prox or Prox
Only Controller (G1-TA, G1-TP)
1
82-0492 Inside Escutcheon Housing Only without Thumb Turn 1
82-0494 Inside Escutcheon Housing Only with Thumb Turn 1
52-2440 100 (LK) User Key Pad Controller Assembly 1
52-2783 2000 (G1-LU) User Controller Assembly 1
52-2784 2000 User (G1-PA, G1-PK) Controller Assembly 1
52-2786 2000 User Keypad/Prox Controller Assembly with RF Technology
(G1-TA, G1-TP)
1
52-2785 2000 User Keypad Controller Assembly with RF Technology
(G1-TU)
1
3 52-0170 Battery Cover 1
52-2509 Battery Cover – RF Technology (G1-TU,G1-TP, G1-TA) 1
ITEM PART No. DESCRIPTION REQ’D
4 01-1212 Security Screw 1
5 01-0297 Security Tool 1
7 82-0507 Thumb Turn 1
8 77-0772 Spindle (Thumb Turn) 1
9 01-0844 Washer (Thumb Turn) 1
10 01-0543 Spring Grip Fastener (Thumb Turn) 1
11 77-0168 Through-bolts #8-32 x 1 7/8” Flat Head Screw 2
12 52-0033 Fire Stop Plate 1
13 01-1500 Fire Stop Screws #8 x 1/2” Type “AB” Phillips Pan Head
Self Tap
2
14 82-3088 Inside Spindle Adapter & Plate Assembly 1
15 01-1495 Screw #8-32 x 1/2” 2
16 82-0368 Inside Spindle/Outside Spindle 2
17 82-0347 Inside Spring/Outside Spring 2
18 82-0081 Face Plate no Dead Bolt 1
19 82-0084 Face Plate with Dead Bolt 1
20 01-1028 Face Plate Screws Machine 8-32 x 1/4” 2
21 01-2299 Lock Body Screws/Wood Door #12 x 1 1/4” 2
22 01-1019 Lock Body Screws/Metal Door 12-24 x 1/2” 2
23 82-0184 Cap Nut 1
24 01-0079 Washer 2
25 82-3082 Plate Assembly 1
26 81-0723 Post 2
27 01-1472 Lever Handle Screw, A, E & F Lever 1
28 01-1174 Lever Handle Screw, B, J, L, P & W Lever 1
29 Reference Profile Series catalog for available lever handles
30 Reference Profile Series catalog for available lever handles
31 G1-8276-hand-finish Lockbody Assembly with deadbolt & cylinder 1
1
1
1
G1-8277-hand-finish Lockbody Assembly with deadbolt only (no cylinder)
G1-8278-hand-finish Lockbody Assembly with cylinder only (no deadbolt)
G1-8279-hand-finish Lockbody Assembly without deadbolt & without cylinder
32 01-0803 Battery Alkaline (“AA” cell - not shown) 6
33 52-0253 Battery Keeper 1
52-0344 Battery Keeper – RF Technology (G1-TU, G1-TP, G1-TA) 1
34 10-0649 Gasket, weatherseal 1
Parts Breakdown (Continued)

6 1-800-810-WIRE • www.sargentlock.com • A7855C
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
01/31/14
Profile Series v.G1.5/LK Mortise Lock
Installation Instructions
6
Step #1 – Verify Hand and Bevel of Door
A. Verify Hand and Bevel of Door
Stand on outside/locked side of door when determining the door hand
B. Prepare Door
Prep door according to Instruction Sheet A7454 and appropriate template:
Manufacturer Door Template: 4632
Through-bolt Hole
Outside Cylinder Hole
(76 and 78 Functions)
Lever Handle Hole
Pre-drilled
and/or
Tapped Holes
(2 places)
Mortised
Pocket
Ribbon Cable Hole
(Controller to Keypad)
Inside Cylinder Hole
Thumb Turn Lever Hole
Lever Handle Hole
Outside of DoorInside of Door
Through-bolt Hole
Fig. 1B Wood Door Preparation
LH
Left Hand
Hinges Left
Open Inward
LHRB
Left Hand
Reverse Bevel
Hinges Left
Open Outward
RH
Right Hand
Hinges Right
Open Inward
RHRB
Right Hand
Reverse Bevel
Hinges Right
Open Outward
Fig. 1A

01/31/14
1-800-810-WIRE • www.sargentlock.com • A7855C 7
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Profile Series v.G1.5/LK Mortise Lock
B. Reverse Latch Hand
Beveled surface of latchbolt must face strike (Fig. 2B).
The deadlatch is self adjusting.
To change the hand of the latchbolt:
1. Insert the blade of a slotted screwdriver (>1/4”)
into the spade shape slot behind latch.
2. Rotate the screwdriver 90° to push latchbolt out
until back of bolt clears lock case front.
3. Rotate latchbolt 180° until the latchbolt
drops back into the lock body.
Note: Latch cannot be unscrewed.
Latchbolt
Spade
Shaped
Slot
Fig. 2B
A. Reverse Lock Hand
Red surface of locking piece must face the outside/locked side of door. To rotate locking piece (Fig. 2A):
1. Position lock body with red surface of locking piece visible.
2. Insert blade type screwdriver into locking piece slot to rotate locking piece toward back of lock body.
3. Rotate the locking piece 180° until RED surface is on opposite side.
Note: Red indicates locked side (outside).
Locking Slide
Red on Locked Side
Push In
Right Hand
Lock Shown
Fig. 2A
Deadlatch
Step #2 – How to Change Hand of Lockbody

8 1-800-810-WIRE • www.sargentlock.com • A7855C
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
01/31/14
Profile Series v.G1.5/LK Mortise Lock
1. Insert lock body into mortised cutout (Fig. 3A).
2. Hold lock body loosely in place with (2) lock
body screws.
Note: Do not completely tighten screws at this time.
Step #3 – Install Lock Body
Fire-rated doors require a fire stop plate on
the outside of the door (Fig. 4A).
1. Drill (2) 1/8” x 1-1/4” deep holes
in the door if not already present.
Refer to template for fire-stop
prep locations.
2. Attach with flap up and
out using (2) #8 x 1/2”
self-tapping screws for
wood and metal doors.
B. Weather Conduit
(P/N 52-2847)
Install weather conduit on
NON FIRE-RATED exterior
doors only.
1. Carefully insert the weather
conduit into the ribbon cable
hole on the inside of the door
(Fig. 4B).
2. Place the O-ring around the
weather conduit on the out-
side and up against the door
(Fig. 4C).
of 1-1/2”
Diameter
(2) 1/8” Diameter
Holes Required
Fire Stop Plate
Slot
(2) Self Tapping
Screws #8 x 1/2”
for Wood and
Metal Doors
Fig. 4A
A. Fire Stop Plate (P/N 53-0033)
7/8”
1-1/2”
Outside of Door
Non-Cylinder Side
Fig.4B
Ribbon Cable Hole
Fig.4C
O-Ring
Outside of Door
Step #4 – Exterior Door Options
(2) #12-24 x 1/2”
Flat Head Screws
(Metal Doors)
(2) #12 x 1-1/4”
Flat Head Screws
(Metal Doors)
Fig. 3A
Harness exits
Non-Cylinder side

01/31/14
1-800-810-WIRE • www.sargentlock.com • A7855C 9
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Profile Series v.G1.5/LK Mortise Lock
Step #6 – Install Outside Escutcheon and Lever Assembly
1A. For 12- fire rated doors: Feed ribbon cable with connector and ground wire from
outside of door through weather seal gasket and fire stop plate (Fig. 6A).
Note: Install ribbon cable with cable exiting down
1B. For non-12- fire rated doors: Feed ribbon cable with connector and ground
wire from outside of door through weather seal gasket (if used)
and weather conduit (not shown).
Note: Install ribbon cable with cable exiting down, orienting with side
marked ‘TOP’ facing up.
2. With outside lever horizontal, locate the outside escutcheon on the door,
while directing the mounting posts through the door and lock body (Fig. 6B).
3. Make certain the lever spindle is properly engaged in lock.
4. On the inside of the door, insert spindle into square hole of mortise lock.
5. Slide inside adapter and plate assembly over spindle
and loosely secure with 2 through
bolt screws (#8-32 x 5/8”).
Note: For 8276 and 8278,
loosely thread cylinder through
escutcheon and into the lock
body before tightening the
lock case screws and
escutcheon through-bolts.
Fig. 5B
Step #5 – Install Weatherseal Gasket (Exterior Doors)
1. Carefully remove the backing from the gasket.
2. Apply gasket to escutcheon:
• Starting in one place, press the adhesive side
of the gasket firmly against the escutcheon.
• Work around the escutcheon, pressing the sticky side
of the gasket firmly against the escutcheon edge.
• The gasket should be aligned so that all edges
of the escutcheon are covered.
3. Attach escutcheon to the door.
Note: The 43 cylinder may be used with or without a gasket.
Fig. 5A
Mortise Lock
Body Connector
and Wire
Fig. 6B
Outside of Door
Ground
Wire
Keypad
Ribbon Cable
Connector
TOP
Inside of Door
Fig. 6A

10 1-800-810-WIRE • www.sargentlock.com • A7855C
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
01/31/14
Profile Series v.G1.5/LK Mortise Lock
Step #7 – Inside Escutcheon Wire Connections
Images are shown without gasket.
If gasket is necessary, refer to Step #5.
Before the controller is attached
to the door:
1. Attach the reader assembly
ribbon cable into the back
of the controller assembly
(side that faces towards
the door when mounted
(Fig. 7A).
2. Attach the ground wire to
the bottom of the controller
assembly (E1, Fig. 7A).
3. Connect the cable from
the cylindrical lock to
the bottom of the controller
assembly (TB1, Fig. 7B).
If Hardwiring is required,
go to “Hardwire Wiring Options”
on page 14.
4. Place extra wire inside door hole
and/or outside escutcheon,
being careful not to pinch wires.
Connectors go on only one way.
Do not offset connectors, and make
sure they are completely seated.
Ground
Wire
Fig. 7A
1
Outside
Escutcheon
2
Ground
Wire
Reader
Cable
Reader
Ribbon
Cable
1
Inside
Escutcheon
(Back)
3
TB1
Inside of Door
3
2
Lock
Cable
RedBlack
Red
Black
Green
Green
With
Deadbolt
Without
Deadbolt
Fig. 7B
Lock Body
Wire Harness
Lock Body
Wire Harness TB1
Ground
Motor
Connector
Remote Power
REX Connector
TB1
TB1 3

01/31/14
1-800-810-WIRE • www.sargentlock.com • A7855C 11
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Profile Series v.G1.5/LK Mortise Lock
1. Slide lever handle onto spindle
until fully seated (Fig. 8A).
2. Insert #8-32 x 1-1/4” screws through inside
escutcheon and thread into outside escutcheon.
3. Straighten escutcheons and tighten securely.
4. Tighten the set screw securely with 1/8” hex
wrench.
Step #8 – Inside Lever Installation
Step #9 – Install and Secure Cylinder
1. Slide cylinder through the spring and rosette/collar
and screw into lock body, rotating the cylinder clockwise (Fig. 9A).
Cylinder should be flush with rosette/collar.
Note: The 43 cylinder may be used when installing
this product with or without a gasket.
Note: SARGENT logo must be horizontal and
on the top of the cylinder (Fig. 9B).
2. Secure the cylinder by tightening cylinder clamp
screw located above the deadbolt using #2
Phillips screwdriver (Fig. 9C).
3. Using the key, test cylinder functions:
• 8278 Function: Key retracts latch
• 8276 Function: Key retracts
latch and projects and
retracts deadbolt
Fig. 9B
Position cylinder so that the
SARGENT logo is right-side up.
Correct Incorrect
Fig. 9C
Outside of Door
Cylinder Clamp Screw
#2 Phillips
Screwdriver
Fig. 9A
Outside of Door
Key
Type 43 Cylinder
Inside of Door
Fig. 8A
Spindle
Set Screw
Inside Lever

12 1-800-810-WIRE • www.sargentlock.com • A7855C
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
01/31/14
Profile Series v.G1.5/LK Mortise Lock
Step #10 – Attach Front Plate
Attach front plate with (2) flat head screws.
Step #11 – Attach Battery Keeper and Cover
1. Secure the inside escutcheon using two #8-32 screws through top and
bottom of the escutcheon (Fig. 11A). Thread into outside escutcheon.
Note: For RF Technology versions (G1-TU, G1-TP, G1-TA),
refer to “RF Technology Lock” section on page 14
to install through-bolt screws.
2. Straighten escutcheons and tighten securely,
being careful to avoid pinching wires.
3. Attach inside cover to escutcheon
making sure to line up tabs with
retaining slots in cover.
4. Secure with security screw
using security tool (P/N 01-0297)
provided (Fig. 11A).
Inside of door
Fig. 11A
Battery Keeper
Battery
Cover
Security
Screw
Security Tool
01-0297
(Included)
#8-32
Screws
#8-32
Screws
Fig. 10A
Front Plate
(2) Flat Head Screws
Lock Body Screws
Outside
of Door

01/31/14
1-800-810-WIRE • www.sargentlock.com • A7855C 13
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Profile Series v.G1.5/LK Mortise Lock
Tabs
Fig. 13A
Retaining Slots
Step #13 – Install Inside Cover
1. Attach inside cover to escutcheon making
sure to line up tabs with retaining
slots in cover.
2. Secure with security screw using
provided security tool Fig. 13A).
Step #12 – Install and Remove Batteries*
A. Install Batteries and Keeper
1. Place (6) “AA” batteries into the compartment, being careful to properly align polarity (Fig. 12A).
2. To install battery keeper, insert the tabs on the bottom of the keeper into the battery compartment slots
and press the keeper tightly against batteries and inserting tabs into bottom slots.
• For RF technology, use RF Technology lock information “RF Technology Lock” on page 14.
IMPORTANT: *Do not install batteries if controller is powered by external power supply.
• Test for proper operation before closing door.
B. Remove Battery Keeper
To remove the battery keeper, pull the keeper away from the batteries (Fig. 12B).
Fig. 12B
+
-
+
+
-
+
Fig. 12A
Bottom Tabs
(Battery Keeper) Keeper Tabs
Battery Keeper
Tip Out

14 1-800-810-WIRE • www.sargentlock.com • A7855C
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
01/31/14
Profile Series v.G1.5/LK Mortise Lock
Installation for the RF Technology Lock for
G1-TU, G1-TA, G1-TP is, for the most part,
installed as described in section 6.
In addition:
The antenna board must be carefully
moved to access the upper through-bolt
screw. Care should be taken to prevent
damage to the antenna retaining tabs
during this process (Fig. 7A).
1. Press the two tabs away from the
antenna board and lift the board
off the mounting posts.
2. Insert the flat head through-bolt and
secure the escutcheon in place.
3. After tightening the top through-bolt,
replace the antenna board by placing
it on the mounting posts and pressing
into the retaining tabs.
RF Technology Lock
7Flathead
Through-bolt
Fig. 7A
Antenna
Board
Mounting
Posts
Antenna
Board
Antenna Board
Retaining Tabs
Controller
Assembly

01/31/14
1-800-810-WIRE • www.sargentlock.com • A7855C 15
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Profile Series v.G1.5/LK Mortise Lock
Hardwiring options include one or a combination of Forced/Propped Door, Hard Power and/or Remote
Unlock (REX). Refer to the examples on the following pages:
1. Forced/Propped Door Option (DM-).
2. Hard Power and Remote Unlock (91-).
3. Hard Power and Remote Unlock (-91), with Forced Propped Door (DM-).
Important
1. Caution: Disconnect all input power before beginning installation to prevent electrical shock and
equipment damage.
2. Installer must be a trained, experienced service person.
3. All wiring must comply with applicable local electrical codes, ordinances and regulations.
Installation Notes
1. With new applications, an ElectroLynx® door harness with 8 and 4 pin connectors will be
pre-installed inside door by ASSA ABLOY door manufacturer when specified during ordering process.
2. Wiring to pigtail harness is per facility wiring requirement.
ElectroLynx® connector terminations and wire colors all match.
3. If door does not have an ElectroLynx® type door harness, cut connectors off product and hard-wire,
or consult factory for appropriate mating harness.
ElectroLynx®
As part of their promise to provide innovative, fast and effective, and higher security
solutions to their customers, ASSA ABLOY Group companies offer ElectroLynx, a
universal quick-connect system that simplifies the electrification of the door opening.
ElectroLynx® is a registered trademark of ASSA ABLOY, Inc.
Locking Mechanism
Plug
Receptacle
ElectroLynx® Connector System Notes
The system is designed to be installation friendly with connectors
from the electric hinge through the door to the rail. The only wiring
required is to the loose wires on the pigtail harness
assembly on the frame side of the electric hinge.
IMPORTANT:
The plug and receptacle connectors are designed to mate and lock
together as shown in the figure. Plug the connectors into each other
with the locking mechanism aligned as indicated.
Do NOT force connectors on any other way.
Wiring Options
8

16 1-800-810-WIRE • www.sargentlock.com • A7855C
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
01/31/14
Profile Series v.G1.5/LK Mortise Lock
Before the controller is attached to the door (Fig. 1A):
1. Attach the reader cable to the controller.
2. Attach the connector from the lock into the bottom
of the circuit board (TB2, Fig. 3B).
3. Plug the ground wire into the bottom of the controller assembly (E1, Fig. 3B).
4. Route the connector from the raceway through the top opening between the controller and the escutch-
eon, along the battery keeper, back under the bottom opening between the controller and escutcheon and
attach at the bottom of the controller.
Note: Connectors go on only one way.
Do not offset connectors and make sure they are completely seated.
A
A
B
C
D
Fig. 1
ElectroLynx Lock Wire Connections
Door Position Switch (DPS)
Install the SARGENT 3287 Door Status Switch according to
instructions included in the kit.
Wire the 3287 Door Status Switch to the ElectroLynx frame har-
ness and to the door status wires:
1. Connect the common wire of the switch to the common wire
of the harness.
2. Connect the normally open wire of the switch to the door
position wire of the harness.
Note: The third wire (normally closed) of the 3287 Door Sta-
tus Switch is not used for this type of system.
Inside
Escutcheon
(Back)
Inside of Door
1
1
2
3
4
4
4
2
Inside
Escutcheon
(Front)
Fig. 1A

01/31/14
1-800-810-WIRE • www.sargentlock.com • A7855C 17
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Profile Series v.G1.5/LK Mortise Lock
321
4-pin
Connector
Installation
1. ElectroLynx® System Wiring Instructions (Fig. 1, 1A and Fig. 2):
a. Look for the mating part on ASSA ABLOY doors and frames.
b. Plug in all connectors during product installation (Fig. 2).
c. Hard wire door status switch as shown
2. Non-ElectroLynx® System Wiring Instructions (Fig. 1 and Fig. 2):
a. Cut the 4-pin connector off the Forced/Propped harness and hard wire to
non-ElectroLynx® two conductor door harness.
b. DM- requires two conductors.
c. Hard wire door harness to power transfer device.
d. Hard wire door status switch to power transfer device.
Fig. 2
Forced/Propped Door
Connector J4
Forced/Propped Door Option
ElectroLynx Wiring System
Door Status Switch
*Wire for switch contact closure
when door is opened - Typical
locations shown in Fig. 1 QC4A Electric Hinge
With 4-pin connectors and pigtail harness
ElectroLynx Door Harness
With 8 and 4-pin connectors
(Harness location dependent on door type)
DM- Prefix (52-3409)
Forced/Propped Door Harness
Ground
Tab E3
Option #1 – Forced / Propped Door (DM-)
D
C B
A
Door
Inside
Escutcheon
Outside
Escutcheon
(TB2) Remote/Power
Unlock Connector
(TB1) Motor
Connector
1 - Red
2 - Black
3 - White (C)
4 - Green (*NC)
4 - Tan
3 - Pink
A
B
C
D
Fig. 1
1 - Red
2 - Black
3 - White
4 - Green

18 1-800-810-WIRE • www.sargentlock.com • A7855C
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
01/31/14
Profile Series v.G1.5/LK Mortise Lock
Option #2 – Remote Power and Remote Unlock (91-)
A
B
C
D
Fig. 1
Installation
1. ElectroLynx® System Wiring Instructions (Fig. 1, 1A and Fig. 3):
a. Look for the mating part on ASSA ABLOY doors and frames.
b. Plug in all connectors during product installation (Fig. 3).
c. Hard wire hard power and/or remote unlock (REX) (Fig. 3).
2. Non-ElectroLynx® System Wiring Instructions (Fig. 1 and Fig. 3):
a. Cut the 8-pin connector off the Remote Power/Unlock
harness and hard wire to non-ElectroLynx® door harness.
b. Remote power requires three conductors and
remote unlock requires two conductors.
c. Hard wire door harness to power transfer device.
d. Hard wire door status switch to power transfer device.
*IMPORTANT: (6) “AA” batteries MUST be removed from
controller when using 3267 power supply.
Ground Tab E3 (TB2) Remote/Power
Unlock Connector
(TB1) Motor
Connector
Door * Inside
Escutcheon
Outside
Escutcheon
A
Note: Refer to 3267 Power
Supply
Instruction Sheet A7477
Fig. 3A
Remote Powering and Remote Unlocking
ElectroLynx Wiring System
QC4A Electric Hinge
With 8-pin connectors,
8 wires and pigtail harness
ElectroLynx Door Harness
With 8 and 4-pin connectors - Harness location is
dependent
on door type
91-Prefix (52-3010)
Remote Power and
Unlocking Harness
C B
Normally Open
Momentary Switch
(Remote Unlock
REX Option)
1 - Red 2 - Black 3 - White 4 - Orange 5 - Blue 6 - Brown 7 - Yellow 8 - Green
1 2 3 4 5 6 7 8
+9V (-) REX REX Data Out Data In RTS EGND
120VAC L/N/G
* 3267 9VDC
Power Supply
1 - Black
2 - Red
3 - White (NO)
4 - Green
5 - Orange (C)
6 - Blue
7 - Brown
8 - Yellow
-9VDC
+9VDC
EGND
1 - Black
2 - Red
3 - White (NO)
4 - Green
5 - Orange (C)
6 - Blue
7 - Brown
8 - Yellow

01/31/14
1-800-810-WIRE • www.sargentlock.com • A7855C 19
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
Profile Series v.G1.5/LK Mortise Lock
Option #3 – Hard Power/Remote Unlock (91-) Combined With Forced/Propped Door (DM-)
Fig. 1
A
B
C
D
Installation
1. ElectroLynx® System Wiring Instructions (Fig. 1, 1A and Fig. 3):
a. Look for the mating part on ASSA ABLOY doors and frames.
b. Plug in all connectors during product installation (Fig. 3).
c. Hard wire hard power and/or remote unlock (REX) (Fig. 3).
2. Non-ElectroLynx® System Wiring Instructions (Fig. 1 and Fig. 3):
a. Cut the 8 and 4-pin connectors off the Remote Power/Unlock
harness and hard wire to non-ElectroLynx® door harness.
b. Remote power requires three conductors; and remote unlock
and DM- require two conductors.
c. Hard wire door harness to power transfer device.
d. Hard wire door status switch to power transfer device.
*IMPORTANT: (6) “AA” batteries MUST be removed from
controller when using 3267 power supply.
Ground Tab E3 (TB2) Remote/Power
Unlock Connector
(TB1) Motor
Connector
Door * Inside
Escutcheon
Outside
Escutcheon
A
Note: Refer to 3267 Power
Supply
Instruction Sheet A7477 Fig. 3A
Remote Powering and Remote Unlocking
ElectroLynx Wiring System
QC4A Electric Hinge
With 8-pin connectors,
8 wires and pigtail harness
ElectroLynx Door Harness
With 8 and 4-pin connectors - Harness location is
dependent
on door type
C B
Normally Open
Momentary Switch
(Remote Unlock
REX Option)
1 - Red 2 - Black 3 - White 4 - Orange 5 - Blue 6 - Brown 7 - Yellow 8 - Green
1 2 3 4 5 6 7 8
+9V (-) REX REX Data Out Data In RTS EGND
120VAC L/N/G
* 3267 9VDC
Power Supply
1 - Black
2 - Red
3 - White (NO)
4 - Green
5 - Orange (C)
6 - Blue
7 - Brown
8 - Yellow
-9VDC
+9VDC
EGND
Door Status Switch
*Wire for switch contact closure
when door is opened - Typical
locations shown in Fig. 1
D
1 - Red
2 - Black
3 - White (C)
4 - Green (*NC)
321
4 - Tan
3 - Pink
1 - Black
2 - Red
3 - White (NO)
4 - Green
5 - Orange (C)
6 - Blue
7 - Brown
8 - Yellow
1 - Red
2 - Black
3 - White
4 - Green

20 1-800-810-WIRE • www.sargentlock.com • A7855C
Copyright © 2014, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Reproductions in whole or in part without express written permission of Sargent Manufacturing Company is prohibited.
01/31/14
Profile Series v.G1.5/LK Mortise Lock
For devices with cylinders, insert key into cylinder and rotate.
Check to see if:
1. The key retracts the latch.
Key should rotate freely.
Key should extend and retract the deadbolt (if applicable).
2. The inside lever retracts latchbolt.
Thumbturn should extend and retract the deadbolt (if applicable).
3. Enter 1234* to unlock outside lever handle and retract latch and deadbolt if provided).
Note: If the lock is prox only (G1-PA) or RF Technology with Prox (G1-TA),
refer to keypad programming instruction manual A7857.
9Operational Check
~½”