Assa Abloy Yale Real Living Assure Lever YRL256 Technical specifications

P/N YRL-LKFTSINSTL-FUL Rev A
1
FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN DAMAGE TO
THE PRODUCT AND VOID THE FACTORY WARRANTY
#7 wood & #8-32
machine x 20mm
Combination screws
x4
M4 x 22mm
Pan head machine
screws
x2
#8-32 x 5/16"
Machine screws
x2
Battery Cover
Key
AA Alkaline
Batteries
Latch
Strike Plate
Interior Mounting Plate
Interior Lock
Battery Cover
Template
Levers
®
Before you begin
for step-by-step installation
instructions & to register
your product
DOWNLOAD
THE BILT APP
®™
Yale Assure Lever Key Free Touchscreen
Installation and Programming Instructions
(YRL256)
Optional
Smart Module*
Key Free
Cylinder
*Yale Smart Module
is not included with
YRL236-NR models.

P/N YRL-LKFTSINSTL-FUL Rev A
2
Preparing to Install
Utility Knife
Drill Wood Mortise
Chisel
Pencil Tape
Measure
Level
Tools necessary only for new
doors or adjusting existing prep.
Template
Tools Needed
Standard
Phillips Head
Screwdriver

P/N YRL-LKFTSINSTL-FUL Rev A
3
Checking Measurements
2-3/8" or 2-3/4"
(60mm or 70mm)
Backset
2-1/8" (54mm)
Diameter
1-3/8" or 1-3/4"
(35mm or 44.5mm)
Door Thickness
1" (25mm)
Diameter

P/N YRL-LKFTSINSTL-FUL Rev A
4
?Determining Door Handing
Left Hand Right Hand
Face a door swinging open
away from you.
If it swings open to the right,
it is a right hand door. If it
swings open to the left, it is a
left hand door.
Exterior
Inswinging Door
Interior Left Hand
Reverse
Right Hand
Reverse
Face a door swinging open
toward you.
If it swings open to the right, it
is a right hand reverse door. If it
swings opens to the left, it is a
left hand reverse door.
Exterior
Outswinging Door
Interior
Outside of Door
Curve of latchbolt must contact strike plate first.
Frame
Door
Latchbolt Curve
Strike
Plate
Exterior
!
Optional
Smart Module
Inside of Door

P/N YRL-LKFTSINSTL-FUL Rev A
5
Preparing Door & Frame
Necessary for new doors or adjusting existing prep.
1" (25mm)
Deep
Inside
of Door
Frame
Frame
!
Drill holes 1/2 way
through door then
complete from other side
to prevent splitting.
2-1/8"
(54mm)
Dia.
2-3/8" (60mm)
or
2-3/4" (70mm)
Backset
1"
(25mm)
Dia.

P/N YRL-LKFTSINSTL-FUL Rev A
6
x4
1Installing Latch & Strike Plate
Right Hand Installation Shown
2-3/8" through bolt posts
2-3/4" through bolt posts
Note: Adjustment based on backset
O
optional
default
PULL
Outside
of Door
Frame
*Backset
*2-3/8" (60mm)
or
2-3/4" (70mm)

P/N YRL-LKFTSINSTL-FUL Rev A
7
2
Outside of
Right Hand Door
Inside of
Right Hand Door
Installing Touchscreen
Right Hand Installation Shown
!
!
“TOP” mark must be
on top surface and tailpiece
in vertical position.
Incorrect orientation will
cause lock to fail.

P/N YRL-LKFTSINSTL-FUL Rev A
8
x2
3Installing Interior Mounting Plate
Right Hand Installation Shown
Inside of
Right Hand Door
Inside of
Right Hand Door

9
4
P/N YRL-LKFTSINSTL-FUL Rev A
Attaching the Cable Assembly
Right Hand Installation Shown
!
Use cable
hooks for
proper cable
routing.
Inside of
Right Hand Door
!Ensure cable is securely
fastened into adapter.

P/N YRL-LKFTSINSTL-FUL Rev A
10
5
X2
Installing Interior Lock
Right Hand Installation Shown
X
Inside of
Right Hand
Door
“Click”

P/N YRL-LKFTSINSTL-FUL Rev A
11
6Installing Exterior Key Free Cylinder
Outside of
Right Hand Door
!Key free cylinder must be installed
with bar away from latch.
Bar
Latch

P/N YRL-LKFTSINSTL-FUL Rev A
12
7Installing Exterior Lever
Outside of
Right Hand Door
!Press pin while installing
lever so lock is not damaged.

P/N YRL-LKFTSINSTL-FUL Rev A
13
8Installing Interior Lever
Inside of
Right Hand Door
!
Press pin while installing
lever so lock is not damaged.

P/N YRL-LKFTSINSTL-FUL Rev A
14
Testing Mechanical Operation
Outside of
Right Hand
Door
Outside of
Right Hand
Door
!Test interior and exterior operation with door open.
!
Test thumbturn and both levers in locked and unlocked positions.
If operation fails, check installation beginning with Step 3 and refer to
Hardware Troubleshooting.

P/N YRL-LKFTSINSTL-FUL Rev A
15
9Installing Optional Smart Module
(if included)
NOTE: If a Smart module was included with your lock, it
is in a separate box with additional module installation
instructions.
Inside of
Right Hand Door
!
Batteries must not be
installed prior to inserting
and/or removing module.

P/N YRL-LKFTSINSTL-FUL Rev A
16
10 Installing Batteries & Cover
Congratulations, you've installed the
®™
Yale Assure Lever Key Free Touchscreen ( )!YRL256
Programming Instructions will help
you customize your product.
Inside of
Right Hand Door
"Welcome to
Yale Real Living."

P/N YRL-LKFTSINSTL-FUL Rev A
17
Testing Touchscreen Operation
!Test with door open.
A Master Enty Code must be created upon installation or after resetting the lock to factory default. Programming
and use of lock is not possible until this step has been successfully completed. See of Programming
Instructions below.
1
Enter Entry Code
Press
!
Enter Entry Code
Press
If touchscreen operation test fails, check installation beginning with Step 2.
OR

18
P/N YRL-LKFTSINSTL-FUL Rev A
Resetting Lock to Factory Default
3. The reset button (see image above) is marked.
2. Remove the interior lock to access the reset button.
4. Re-insert 3 batteries and hold the reset button for 3 seconds.
6. Release the reset button.
7. Re-install the interior lock onto the door.
*Upon reset, Master Entry Code creation is the only option available and
must be performed prior to any other programming of the lock.
1. Remove the battery cover and batteries.
5. While still holding the reset button, insert the 4th battery, and hold the
reset button for an additional 3 seconds.
When resetting the lock, all user codes, including the Master Entry Code*,
are deleted. All programming features are reset to original default settings.
See “Factory Settings”.
Reset Button
Interior Lock

P/N YRL-LKFTSINSTL-FUL Rev A
19
Factory Settings
®
While Yale has included several features to prevent lockout
(9-Volt battery jumper, low battery warnings), it is still possible
for a lockout situation to occur. Because this product does not
®
have a mechanical override (a key), Yale recommends to use
this product in an environment where there are additional
entry points into the dwelling.
NOTE TO INSTALLER AND CONSUMER
*The Master Entry Code must be created prior to any other programming of the lock.
Registration required*
Settings Factory Setting
Master Entry (PIN) Code
Automatic Re-lock Disabled
Lockout Mode Disabled
Wrong Code Entry Limit 5 Times
Shutdown Time 60 Seconds
One Touch Locking Enabled
Inside Indicator Light Disabled (Off)
Automatic Re-lock Time 30 Seconds
Language Setting Mode English
Volume Setting Low

P/N YRL-LKFTSINSTL-FUL Rev A
20
Hardware Troubleshooting
Cycle lock in both the locked and unlocked positions. If problems are found:
Tailpiece and spindle will not mate and fit into the interior escutcheon
a. Ensure that your door is between 1-3/8" and 1-3/4" thick
b. Ensure that the square shaped spindle has “Top” writing and arrow facing upwards
c. Place the tailpiece in the vertical position
d. Verify that the thumb turn is in the horizontal (unlocked) position
Thumbturn does not rotate electronically or physically
a. Verify that inside of the lock is properly seated on the mounting bracket
b. Ensure that the square shaped spindle has “Top” writing and arrow facing upwards
c. Place the tailpiece in the vertical position
d. Verify that the thumb turn is in the horizontal (unlocked) position
I'm getting an alert when I try to lock or unlock the door electronically
a. Do not turn or depress the lever during operation, this could cause a jam alarm
b. Check that thumb turn does not have anything preventing it from physically rotating
c. Verify that you can rotate thumb turn freely
My lock is not making any sound when I push buttons
a. Using the programming tree in the manual to verify that Audio is enabled
b. If Audio is enabled, ensure that the white cable, that connects the keypad to the interior
of the lock, is not pinched or broken
When rotating the thumbturn I hear noise
a. A little bit of noise is normal when operating the thumbturn
b. If cranking, grinding or clicking occurs please verify your installation
The locking pins will not retract when I try to install the levers
a. If the thumb turn is in vertical (locked) position, rotate the thumb turn the horizontal
(unlocked) position and it will retract