Assa Abloy RIXSON FM9930 User manual

FM9930 Floor Mounted Door Release
DR100240A
Contact Plate
Adjusting Screw
Location
THRU BOLT MOUNTING
Notes:
1. Do not scale drawing.
2. Total projection 8-3/16". (Includes Electromagnet, Armature Assembly and Floor Bracket.)
3. Power requirements: 24VAC/DC, .25 amp.
4. See Step 1 on DR100240B for switch box location. Anchor switch box to withstand a
minimum 300 lb. pull.
5. Door closing mechanism should have a 3 lb. closing force at the degree of door opening
where door armature and electromagnet engage.
6. All dimensions given in inches (mm).
7. Holding Force is 3 to 235 Pounds.
WIRING DIAGRAM
24 VAC
24 VDC
-
+
Wall Plate
Electromagnet and
Mounting Bracket
Assembly
Switch
Box
Momentary
Release Switch
(Optional)
Contact
Plate Pull Side
of Door
Door
Plate
6-32 x 5/16" OHMS
(2 Places)
1/4-20 x 2-1/16"
THMS
(2 Places)
1-13/16
(46)
Approx. 3" (76.2)
To Door Edge
2-3/16
(55.6)
3/16
(4.8)
5-3/16
(131.8)
C
LConduit
3/4
(19)
Door
Plate
DR100240A
www.rixson.com
ASSA ABLOY
RIXSON®
DATE
TEMPLATE NUMBER
Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright© 2005, 2009, Yale Security Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
03-09

FM9930 Floor Mounted Door Release
Mounting Floor Portion
1. Locate angle bracket.
2. Attach bracket to floor with three (3) 1/4-20x1-1/2" FHPMS and three (3) 1/4-20
cement anchors.
3. Mount switch box to bracket using three (3) 1/4-20x1/2" RHMS.
4. Connect wire leads from power source to wire leads from magnet, and push wires
back into switch box.
5. Mount magnet assembly to switch box using four (4) 6-32x5/16" FHMS.
6. Mount cover to magn t assembly using two (2) 6-32x5/16" OHMS.e
Mounting Door Portion
1. IMPORTANT: Door portion must be installed with mounting holes in vertical
position.
2. Contact plate adjusting screw must be loose to allow contact plate to swing freely.
3. Remove paper liner on adhesive surface exposing marking template beneath.
NOTE: Template must remain on armature.
4. With electromagnet energized, position contact plate to cover entire magn t surface.
If magnet can not be energized, hold contact plate against magnet nually. Open
door to engage door armature and exert pr ssure. Release door to close. Marking
template will transfer to door. If necessary, align template securely to door.
5. Mark hole locations o door using centerlines on marking template. Drill two (2) 5/16"
dia. holes through door on 1-1/4" centers.
6. Install door armature assembly to door. Must be mounted on pull side of door. Slot in
contact plate adjusting screw must be accessible after mounting.
e
ma
e
DR100240B
DR100240B
www.rixson.com
ASSA ABLOY
RIXSON®
DATE
TEMPLATE NUMBER
Rixson® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Copyright© 2005, 2009, Yale Security Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
03-09