Assa Abloy Yale 7370 Series User manual

7370 Series Multi-Point Lock
for Window Shutter Applications
Installation Instructions
Recommended Installation:
Install 7370 so that the
deadbolt is equidistant from
the top and bottom of the
shutter.
Attention Installer
Any retrofit or other field modification to a fire rated opening can
potentially impact the fire rating of the opening, and Yale Locks &
Hardware makes no representations or warranties concerning
what such impact may be in any specific situation. When
retrofitting any portion of an existing fire rated opening, or
specifying and installing a new fire-rated opening, please consult
with a code specialist or local code official (Authority Having
Jurisdiction) to ensure compliance with all applicable codes and
ratings.
An ASSA ABLOY Group brand
80-8470-7370-010 (10-12)

2
TABLE OF CONTENTS
Step 1 – Installation of Deadbolt Assembly
Step 2 – Installation of Bottom Bolt Assembly
Step 3 – Installation of Top Pusher Assembly
Step 4 – Aligning assemblies in preparation for drilling and pinning
Step 5 – Applying the Drill Jig for proper drilling
Step 6 – Pinning the Rods to engage the Deadbolt Lever
Step 7 – Installation of Inside and Outside Trim
Step 8 – Installation of Cylinder in Outside Trim (Optional)
Step 9 – Assemble the Top Latch to the Frame
Step 10 – Installation of Deadbolt Strike
Step 11 – Install the Bottom Strike
3
3 & 4
4
5 & 6
7
8
8
9
9
10
10
This device is intended to be part of an integrated window shutter, frame and hardware assembly
UL-approved for both FEMA 361 and ICC 500 guidelines for inswing window shutters. This
instruction sheet will take you through the following steps for full installation.
Installation Jig Components Drill Guide for Deadbolt Case
An ASSA ABLOY Group brand
80-8470-7370-010 (10-12)

3
Step 1 – Installation of the Deadbolt Assembly
Step 2 – Installation of the Bottom Bolt Assembly
• Place the window shutter on a horizontal surface
with the pin lever notch located at the top of the
shutter facing up.
• The recommended deadbolt assembly location
should be equidistant from the top and bottom
of the shutter.
• Assemble the deadbolt case into the lock pocket
provided in the door. Note the orientation of the
lock, the top of the deadbolt case indicates that
this should be toward the top of the shutter.
• Assemble the lock to the edge of the shutter
using (2) 1/4-20 x 1" Flat Head Cap Screws.
Lower Thru
Bolt Cutout
•
slide along the lower rod tubing but not slide on its
own when the rod is held vertically. Be sure that the
set screw is oriented so that it will be accessible
through the Lower Thru Bolt Cutout on the top side of
the shutter.
• When you insert the assembly into the shutter and
through the nylon guides of the deadbolt case this
lifting pad will be in a position to allow you to make the
final necessary adjustment. Note the orientation of the
bottom bolt assembly the double screw head side (not
shown in this image) should be facing the hinge side
of the shutter.
Continue on next page………….
Loosen the set screw so that the lifting platform will
Set Screw
An ASSA ABLOY Group brand
80-8470-7370-010 (10-12)

Step 2 – Installation of the Bottom Bolt Assembly continued
4
Nylon Guides •
Sub Assembly into the prep. hole in the bottom of the
shutter. As you guide the assembly up into the shutter
you will need to guide it into the bottom nylon guide of
the Deadbolt Assembly and then up thru the top nylon
guide.
• Seat the bottom bolt bracket against the shutters lower
reinforcement plate.
• Align Bottom Bolt Plate to shutter prep.
• Fasten the Bottom Bolt Assembly and Bottom Bolt
Plate to the bottom of the shutter using (2) #12-24 x 1"
Flat Head Cap Screws.
With the Deadbolt Retracted, slide the Bottom Bolt
Step 3 – Installation of the Top Pusher Assembly
•
shutter, making sure the plunger pin is oriented with
the clearance slot on the stop side of the shutter.
• Visually align the rod of the Top Pusher Assembly so
that it enters the tube of the Bottom Bolt Assembly
that extends out of the Deadbolt Assembly.
• Align the Top Strike plate to shutter prep. noting the
position of the beveled edge. It should be on the
same side as the plunger pin.
• Fasten the Top Strike plate and Top Pusher Assembly
to the top of the shutter using (2) #12-24 x 1" Flat
Head Cap Screws.
Slide this assembly into the prep. at the top of the
Strike Plate
Note beveled edge position
Plunger Pin
Top Pusher
Assembly
An ASSA ABLOY Group brand
80-8470-7370-010 (10-12)

5
Step 4 – Alignment of components in preparation for drilling and pinning
•
so that it extends the top latch to the proper
position for pinning. The Top Bolt Clamp will
assure that the top latch is in the correct
position for final installation.
• Prepare the lifting platform installation jig by
removing the two wing fasteners and their
washers.
• Introduce the lifting platform jig up through the
under side of the shutter as shown.
• Using the two wing fasteners and their
washers, secure the lifting platform jig to the
shutter.
The lifting platform jig will now be in position to
allow sliding the lifting platform (shown in step 2)
so that it rests against the shelf of the jig.
Continued on next page………….
Thread the Top Clamp into the threaded hole
An ASSA ABLOY Group brand
80-8470-7370-010 (10-12)

6
Step 4 – Alignment of components in preparation for drilling and pinning
Before continuing to the next step be certain the
top pusher and bottom bolt are in the correct
position.
• Bottom Bolt should be flush to the bottom of
the shutter.
• The lifting platform (item 1) should be moved
down the bottom rod and placed against the
shelf of the lifting platform jig.
• Next secure the platforms position by
tightening the cone point set screw (item 2).
This will assure the point on the set screw
embeds itself firmly into the bottom rod.
1
2
An ASSA ABLOY Group brand
80-8470-7370-010 (10-12)

7
Step 5 – Applying the drill jig for proper drilling
• Manually project the deadbolt by applying force
to the deadbolt lever toward the bottom of the
shutter.
• The deadbolt lever is now in a position to allow
the Drill Guide to be positioned above the
deadbolt and fixed into position using the two
drill guide positioning holes provided in both
sides of the deadbolt case.
• The Drill Guide is an alligator type jig. Loosen
the Drill Guide clamping screw, allowing the
jaws to rotate 90 degrees to allow the guide to
be positioned above the deadbolt and closed
around the shutter so that the pins on both
sides of the Drill Guide engage the two Drill
Guide Positioning Holes.
• Once the Drill Guide is engaged in the
positioning holes, tighten the Drill Guides
clamping screw so that it will firmly secure the
jig around the shutter.
• Using the Drill Guide Hole, drill a 1/8" hole (drill
provided with jig components) thru both sets of
rods.
Drill Guide
Positioning
Holes
Deadbolt
Lever
Drill Guide
Hole
Drill Guide
Positioning Pins
Drill Guide
Clamping Screw
An ASSA ABLOY Group brand
80-8470-7370-010 (10-12)

Step 6 – Pinning the Rods to engage the Deadbolt Lever
8
Step 7 – Installation of Inside and Outside Trim
Hole shown in proper pinning position.
Drive Pin
• Loosen the Drill Guide clamping screw allowing
the Drill Guide to be removed from the shutter.
• Manually retract the deadbolt by applying force
to the deadbolt lever toward the top of the
shutter.
• This will put the pinning hole in the proper
position for fastening the Drive Pin.
• Insert the Drive Pin from the underside of the
shutter and through the holes in the rods and
fasten the Drive Pin in place with the spring
washer.
• Install the outside trim by inserting it from
underneath the shutter (outside face).
• As it enters the shutter cavity the lifting pad in
the escutcheon will rest on the underside of the
lifting pad secured to the rods in step 4.
• Press the outside escutcheon against the
shutter surface.
• Install the inside trim by placing it over the
shutter prep and positioning the lifting pad of
the inside trim on the underside of the lifting
pad.
• Visually align the mounting holes of the inside
escutcheon to the mounting posts from the
outside escutcheon.
• Insert 4 mounting screws #12 -24 x 1-1/2" and
tighten screws.
The Lifting Platform Jig and the Top Clamp can now be removed from the shutter.
An ASSA ABLOY Group brand
80-8470-7370-010 (10-12)

9
Step 8 – Installation of Cylinder in Outside Trim (Optional)
Cylinder
Cylinder Collar
Cylinder Retaining Nut
Backplate
Outside Trim
Assembly
Step 9 – Assemble the Top Latch to the Frame
• Assembly the top latch into the top of the frame
using (4) 1/4"-20 x 1" Flat Head Cap Screws.
The angled surface should face the shutter.
• Insert the Cylinder into the Cylinder Collar
• Place the Cylinder Retaining Nut against the
backplate of the outside trim assembly,
• Feed the cylinder and cylinder collar into the
cylinder hole of the escutcheon and screw the
cylinder retaining nut to the cylinder until it is
fully seated with the cam straight up as shown.
• Secure the cylinder to the escutcheon by
tightening the cylinder retaining nut.
An ASSA ABLOY Group brand
80-8470-7370-010 (10-12)

Step 10 – Installation of Deadbolt Strike
Step 11 – Install the Bottom Strike
• Assemble the Deadbolt Strike to the frame
using (2) 1/4"-20 x 1" Flat Head Cap Screws.
Deadbolt Strike
• Place the Bottom Strike into the Strike Shim
and fasten to the frame using (2) 1/4"-20
Screws.
Install the Shutter into the frame assembly and shim for proper shutter gap and for the
shutter being square and plumb.
Bottom Strike
Strike Shim
Yale® is a registered trademark of Yale Security Inc., an ASSA ABLOY Group company. Other products' brand names may be trademarks or registered trademarks of their
respective owners and are mentioned for reference purposes only. These materials are protected under U.S. copyright laws. All contents current at time of publication.
Yale Security Inc. reserves the right to change availability of any item in this catalog, its design, construction, and/or its materials.
Copyright © 2010, 2012 Yale Security Inc., an ASSA ABLOY Group company.
All rights reserved. Reproduction in whole or in part without the express written permission of Yale Security Inc. is prohibited.
Product Support Tel 800. • www.yalelocks.com438.1951
Yale Locks & Hardware is a division of Yale Security Inc., an ASSA ABLOY Group company.
An ASSA ABLOY Group brand
80-8470-7370-010 (10-12)