Associated Electrics PRO2 LT10SW SHORT WHEELBASE User manual

2
:: Introduction:: Introduction
:: RTR Features:: RTR Features
:: Additional:: Additional
Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and
maintaining your new RTR. Please take a moment to read through this manual to help familiarize yourself with these steps.
We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the
illustrations. New parts will be noted on supplementary sheets.
Tools included:
• Allen wrenches 1.5mm, 2.0mm, 2.5mm
•12mm Shock Tool
• Multi-wrench
Associated Electrics, Inc.
26021 Commercentre Dr.
Lake Forest, CA 92630
http://www.RC10.com · http://twitter.com/Team_Associated · http://www.instagram.com/teamassociatedrc/ · http://www.facebok.com/TeamAssociated/
Customer Service
Tel: [phone]
Fax: [phone]
:: Other Helpful Items:: Other Helpful Items
• 2.4GHz 2-channel radio with new DVC (Dynamic Vehicle Control) receiver featuring built-in adjustable gyro
• High-torque, metal-gear Reedy Servo with spring style servo saver
• Powerful Reedy 3300kV brushless motor
• Water-resistant high-power Reedy brushless speed control with T-plug connector and LiPo low voltage cutoff
• Water-resistant enclosed receiver box
• Lightweight street stock inspired wheels
• High grip all terrain tires
• Durable and lightweight aluminum top shaft
• Low center-of-gravity molded composite chassis with hook-and-loop battery straps that accommodate both NiMH and 2/3s
LiPo battery packs
• Metric hardware throughout
• 22 precision rubber-sealed ball bearings
• Impact absorbing front and rear bumpers
• Adjustable body mounts
• Rear CVA drive shafts for more reliability
• Aluminum 12mm big bore coil-over shock absorbers
• 2.6:1 ratio gearbox with heavy-duty sealed gear differential and externally adjustable slipper clutch
• Rugged steel turnbuckles for adjustable camber and front toe-in
• Adjustable suspension geometry
• Vertical ball ends for roll center adjustments, front and rear
• Many Factory Team options already available!
Your new RTR comes factory assembled including radio gear, motor, and
ESC. However, there are some items you will need to complete your kit
(refer to catalog section for suggestions):
• AA-size batteries for transmitter (x4)
• Peak Detection Charger or LiPo Compatible Charger
• 6 cell NiMH battery pack or 2S LiPo battery pack w/High Current T Plug.
• Green Slime shock lube (AE # 1105) • FT Tire Adhesive, medium (AE # 1597)
• Thread Locking Compound (AE # 1596) • Silicone Shock Fluid (Refer to catalog for complete listings)
• Silicone Diff Fluid (Refer to catalog for complete listings) • Body Scissors (AE # 1737)
• 7 Piece Hex Driver Set (AE # 1650) • FT Hex Wrenches (AE # 1650)
• FT Dual Turnbuckle Wrench (AE #1114) • Needle Nose Pliers • Soldering Iron
• Calipers or a Precision Ruler • Reamer / Hole Punch • Ride Height Gauge
• FT Nut Drivers (AE #1666 - 1668, used with #1650 handle) • Wire Cutters • Hobby Knife

3
:: Hardware - 1:1 Scale View:: Hardware - 1:1 Scale View
3x8mm (25201)
3x10mm (25202)
3x12mm (25203)
3x14mm (89208)
3x16mm (25204)
Flat Head (fhcs)
2x4mm (31510)
2.5x8mm (31521)
3x5mm (31530)
3x8mm (31532)
3x10mm (25211)
3x12mm (89202)
3x14mm (25187)
3x16mm (89203)
3x22mm (25189)
3x24mm (89204)
3x26mm (89205)
3x30mm (91478)
Button Head (bhcs) Ball Bearings
3x7x3mm (91475)
5x10x4mm (91560)
6x13x5 (91562)
10x15x4 (91563)
3x3mm (25225)
Set Screws
Notes:
E-clip 1/8 (6299)
Clips
Ballstuds
HD 6mm (91047)
HD 8mm (91048)
HD 10mm (91049)
M3 Nut (91477)
M3 Alum. Locknut, Blue (31550)
M3 Locknut, Black (25215)
M3 Locknut w/Flange (25612)
FT 3mm Locknuts, Blue(25392)
M4 Locknut w/Flange (91378)
FT M4 Locknuts w/Flange,
Blue (31551)
Nuts (lock/plain)
Cap Head (shcs)
2.5 x 14mm (71032)
Servo Mount Washer (89218)
(.250 x .125 x .815)
FT Ballstud Washer, Aluminum
(0.5mm) (31381)
FT Ballstud Washer, Aluminum
(1mm) (31382)
FT Ballstud Washer, Aluminum
(2mm) (31383)
3x6x0.5mm Washer (89218)
Shims and Washers

:: Table of Contents:: Table of Contents
:: Notes:: Notes
1................... Cover
2................... Introduction
3...................1:1 Hardware “Fold Out”
4................... Table of Contents
5 - 6..............Quick Start Guide
7.....................Front Top Plate and
Steering Build
8 - 9..............Front Suspension Build
9 - 10...........Rear Suspension Build
10 - 11.........Gear Differential Build
11 - 12........Gearbox Build
12.................Slipper Build
13.................Gearbox Install
14.................Rear Hub and CVA Build
14 - 15........Turnbuckles Build
15 - 17.........Shocks Build
17 - 19........Electronics Build
19 - 20........Bumpers and Chassis
Braces Build
20 - 21........Tires and Body Build
21.................Tuning Tips
22................Back Cover
4
Associated Electrics, Inc.
26021 Commercentre Dr.
Lake Forest, CA 92630
Customer Service
Tel: [phone]
Fax: [phone]
There is a 1:1 hardware foldout page in the
front of the manual. To check the size of a part,
line up your hardare with the correct drawing
until you find the exact size. Each part in the
foldout has a number assigned to it for ordering
replacement parts.
This symbol indicates a special
note or instruction in the manual.
This symbol indicates a Racers Tip.
!
http://www.RC10.com · http://twitter.com/Team_Associated · http://www.instagram.com/teamassociatedrc/ · http://www.facebok.com/TeamAssociated/

5
3/23
:::: Quick Start GuideQuick Start Guide
:::: Quick Start GuideQuick Start Guide - (cont.)- (cont.)
:::: Quick Start GuideQuick Start Guide - (cont.)- (cont.)
Battery Charging Steps and Safety:
Remove the battery from the vehicle before charging.
Place battery on a fire resistant surface.
Avoid any contact with water or other liquids.
Be sure to select the correct charging mode for the type
of battery you are charging.
ALWAYS use a compatible charger for charging your batteries.
Caution: Never leave the battery unattended while charging.
Always disconnect the charger from the power source when
finished charging.
Caution: Always disconnect the battery when you are
finished driving the vehicle.
Battery Installation:
1. Install the battery with the battery
wires directed towards the front of
the vehicle.
2. Secure the hook and loop strap
near the rear shock tower.
Pull the strap over the motor wires
for added security.
3. Secure the hook and loop strap
near the front shock tower.
You may move the foam pad to either
the front or the rear of the battery
compartment to adjust the weight
balance of the vehicle.
Peak Detection
Quick Charger
1 2
3Install antenna wire
through antenna tube,
then install antenna
tube as shown.

6
:::: Quick Start GuideQuick Start Guide - (cont.)- (cont.)
:::: Quick Start GuideQuick Start Guide - (cont.)- (cont.)
Battery Notes and Tip:
Connect the battery as shown.
Disconnect the battery when not in use!
LiPo: LiPo batteries (lithium polymer) are high current
rechargeable batteries. LiPo batteries offer extended run time and peak
performance over NiMH batteries. They require a peak detection charger
designed specifically for LiPo batteries.
These batteries require special care and handling.
LiPo batteries are recommended for advanced users only!
ALWAYS charge a LiPo battery in LiPo mode.
If using a 3S LiPo battery, use a smaller pinion gear as a starting point (use part
#1335 17T Pinion). This provides the gear ratio suggested for the more
powerful 3S LiPo battery. Gearing will depend on the surface you are running
on, and the size of the track/area that you are driving in.
Radio System Tuning and Controls:
RULE: Transmitter on First/Vehicle on Second,
Vehicle off First/ Transmitter off Last!
1) Slide the battery cover to remove cover.
2) Install alkaline or rechargeable AA size
batteries into the battery holder.
3) Slide the battery cover back into place making
sure it is completely closed and secure.
4) Turn the power ON. If the power indicator LED
fails to light, check the batteries for insufficient
contact or incorrect polarity.
On/Off Switch
Radio System Tuning and Controls:
DO NOT hold the trigger when turning on the radio.
If using optional battery for transmitter, be sure to plug
it in correctly. Plugging in a battery backwards can
cause damage.
Refer to Radio owners manual for more in-depth
instructions on radio operation and functions.
Throttle set to Neutral!
Adjust steering
trim so front
wheels point
straight.
Adjust steering
Neutral
Push trigger
for Brake
Pull trigger
for Throttle
Install body and body clips. Ready to go!
straight.

7
:::: Front Top Plate and Steering Build - StepFront Top Plate and Steering Build - Step 22
:::: Front Top Plate and Steering Build - Step 3Front Top Plate and Steering Build - Step 3
:: Front Top Plate and Steering Build - Step 1:: Front Top Plate and Steering Build - Step 1
Do not overtighten steering bolts. Make sure
there is free movement in the steering rack.
!
Note orientation
of steering rack.
!
Note orientation
of the brace.
!
91475
3 x 7 x 3
Ball Bearing
91391
Steering
Rack
x4x4
x2x2
x2x2
91047
Heavy-duty
Ballstud,
6mm
91391
Steering
Rack Crush
Tube
91391
Steering
Bellcrank
Brace
x2x2
89202
M3 x 12mm
BHCS
91047
Heavy-duty
Ballstud,
6mm
x2x2
25204
M3 x 16mm
FHCS
91391
Steering
Bellcrank
Brace
91475
3 x 7 x 3
Ball Bearing
x4x4
x2x2
25189
M3 x 22mm
BHCS
91358
Chassis
Brace Set
(Top Plate)
x2x2
25202
M3 x 10mm
FHCS
91359
Bulkhead
71092
Chassis

8
:::: Front Suspension BuildFront Suspension Build - Step 1- Step 1
:::: Front Suspension BuildFront Suspension Build - (LT10, DK10) -- (LT10, DK10) - Step 3Step 3
:::: Front Suspension BuildFront Suspension Build -- Step 2Step 2
Build 2 (1 left, 1 right)
Build 2 (1 left, 1 right)
71003
Front Shock
Tower
91049
Heavy-duty
Ballstud, 10mm
x2x2
x2x2
31383
FT Ballstud
Washer,
Aluminum
(2mm)
25201
M3 x 8mm
FHCS
91477
M3 Nut
(Black)
x2x2
89205
M3 x 26mm
BHCS
71066
Front Body
Mount
x2x2
x2x2
x2x2
31509
M2 x 3mm
BHCS
31509
M2 x 3mm
BHCS
91394
Hinge Pin
(front, outer)
71068
Front Arms
91394
Hinge Pin
(front, Inner)
71049
Front Hinge
Pin Brace
25211
M3 x 10mm
BHCS
x2x2
#1596
thread lock
91048
Heavy-duty
Ballstud,
8mm
91417
Caster
Block
x2x2
31530
M3 x 5mm
BHCS
25215
M3 Locknut,
black
91560
5 x 10 x 4
Bearing
71127
Front
Axles
91417
Steering
Block
#1596
thread lock
91047
Heavy-duty
Ballstud,
6mm
x2x2
89202
M3 x 12mm
BHCS
91402
Caster
Block
Bushing
x2x2

9
:::: Front Suspension BuildFront Suspension Build -- ((LT10, DK10LT10, DK10) -) - Step 4Step 4
:::: Rear SuspensionRear Suspension BuildBuild - Step 1- Step 1
:::: Front Suspension BuildFront Suspension Build - (- (LT10, DK10LT10, DK10) - Step 5) - Step 5
91359
C Mount
91359
Rear Chassis
Plate
31521
M2.5 x 8mm
BHCS
LT10
DK10
71068
Rear Arms
x2x2
91394
Hinge Pin
(rear, Inner)
25187
M3 x 14mm
BHCS
91359
D Mount
x2x2
89202
M3 x 12mm
BHCS
x4x4
71032
M2.5 x 14mm
SHCS
71035
Front Body
Post
x2x2
x2x2

10
:::: RearRear Shock Tower and Bumper BuildShock Tower and Bumper Build - Bag- Bag D - DDD - DD - Step 2- Step 2
:: Rear:: Rear Shock Tower and Bumper Build - Bag D - DD - Step 1Shock Tower and Bumper Build - Bag D - DD - Step 1
:::: FrontFront Shock Tower and Bumper BuildShock Tower and Bumper Build - Bag C - Step 3- Bag C - Step 3
89204
M3 x 24mm
BHCS
x2x2
91477
M3 Nut
(Black)
x2x2
71003
Rear Shock
Tower
:::: Rear SuspensionRear Suspension BuildBuild - Step 2- Step 2
:::: Rear SuspensionRear Suspension BuildBuild - Step 3- Step 3
:::: Gear DiffGear Diff BuildBuild - Step 1- Step 1
91463
Gear Diff
Washer
9831
Gear Diff
O-Ring
(Small)
91463
Gear Diff
O-Ring
(Large)
x2x2
91465
Gear Diff
Outdrive
91466
Gear Diff
Gear
42025
Gear Diff
Outdrive
Pin
91463
Gear Diff
Sun Gear
91463
Gear Diff
Planet
Washer
91463
Gear Diff
Planet
Gear
91463
Gear Diff
Cross Pin
x4x4
x4x4
x2x2
89208
M3 x 14mm
FHCS
25203
M3 x 12mm
FHCS
x2x2
x2x2
x2x2
x2x2
25211
M3 x 10mm
BHCS
25211
M3 x 10mm
BHCS
25187
M3 x 14mm
BHCS
91358
Rear Chassis
Brace
x2x2
31383
FT Ballstud
Washer,
Aluminum
(2mm)
91049
Heavy-duty
Ballstud, 10mm
x2x2
x2x2

11
:::: Gearbox Build - Step 1Gearbox Build - Step 1
91560
5 x 10 x 4,
Bearing
915563
10 x 15 x 4,
Bearing
91430
Gearbox
(right & left)
91132
Idler Gear
Shaft
x2x2
x2x2
:::: Gear DiffGear Diff BuildBuild - Step 3- Step 3
:::: Gear DiffGear Diff BuildBuild - Step 2- Step 2
Idler Gear
* Ensure free outdrive
rotation before
installation!
!
42025
Gear Diff
Outdrive
Pin
91463
Gear Diff
Sun Gear
91463
Gear Diff
O-Ring
(Large)
91465
Gear Diff
Outdrive
91466
Gear Diff
Gear
91463
Gear Diff
Washer
9831
Gear Diff
O-Ring
(Small)
x2x2
9831
Gear Diff
Gasket
31350
M2.5 x 10mm
FHCS
x4x4
91560
5 x 10 x 4,
Bearing
91466
Idler Gear
x2x2
#6588
black grease
* Fill diffs to this level
!
Diff fluid
#5463,
500k

12
:::: Slipper Build - Step 1Slipper Build - Step 1
:::: Gearbox Build - Step 3Gearbox Build - Step 3
:::: Gearbox Build - Step 2Gearbox Build - Step 2
25202
M3 x 10mm
FHCS
x3
x2x2
x2x2
91428
Motor Plate,
Blue
9611
Slipper
Pad
7485
FT V2
Slipper Hub 9654
Spur Gear
87T, 48P
31532
M3 x 8mm
BHCS
x2
89203
M3 x 16mm
BHCS
x5
Add a drop of Diff
Lube (#6591) to
the teeth of the diff
gear, idler gears,
and top shaft.
!
#6591
diff lube
M3 x 8mm
BHCS
89203
x5x5
Lube (#6591) to
the teeth of the diff
gear, idler gears,
and top shaft.
!
#6591
diff lube
25202
x3
x3
91428
Motor Plate,
91606
Top Shaft
Aluminum
91431
Motor
Guard
91478
M3 x 30mm
FHCS
x2x2 71038
Body Mount
Brace
(Left & Right)
x2x2
9739
Slipper
Spring
31551
M4 Locknut,
with flange
and knurl
91423
Slipper
Spring
Adapter

13
:::: Gearbox Install - Step 3Gearbox Install - Step 3
:::: Gearbox Install - Step 2Gearbox Install - Step 2
:::: Gearbox Install - Step 1
The Locknut should
be flush with the
top shaft when
installed.
See page 23 for gear
mesh, and slipper clutch
setting instructions!
!
!
The Locknut should
be flush with the
top shaft when
25211
M3 x 10mm
BHCS
x2x2
25203
M3 x 12mm
FHCS
x2x2
71066
Rear Body
Post
71066
Rear Body
Post Pivots
71038
Rear Body
Mount
25204
M3 x 16mm
FHCS
x2x2
x2x2
x2x2
71032
M2.5 x 14mm
SHCS
25202
M3 x 10mm
FHCS
x2x2
x4x4
LT10
DK10

14
:::: Turnbuckles Build - Step 1
:::: Rear Hub and CVA Build - Step 2Rear Hub and CVA Build - Step 2
:::: Rear Hub and CVA Build - Step 1Rear Hub and CVA Build - Step 1
Build x2 (right and left side)
Build x2 (right and left side)
Build x2 (right and left side)
91562
6 x 13 x 5
Bearing
91563
10 x 15 x 4
Bearing 91418
Rear Hub
91048
Heavy-duty
Ballstud, 8mm
91562
6 x 13 x 5
91436
CVA Wheel
Hex Pin
91418
Wheel
Hex (rear) 31509
M2 x 3mm
BHCS
91394
Hinge Pin
(rear, outer)
91438
CVA
Pin
#6588
black grease
91438
CVA
Coupler
91439
CVA Bone
65mm
71019
HD
CVA Axle
91469
Ball Cup
91469
Ball Cup
91723
Turnbuckles,
3x48mm
Build x2 (right and left side)
Orient the notch
to the left throughout the
car. It indicates which end
has the left hand threads!
!Racers Tip:
Use black grease
(#6588) on the
threads of the
turnbuckles for
easier ball cup
installation!
27.00mm
Steering Turnbuckle
Orient the notch
!

15
:::: Shocks Build - Step 1Shocks Build - Step 1
:::: Turnbuckles Build - Step 3Turnbuckles Build - Step 3
:::: Turnbuckles Build - Step 2
91444
12mm
Shock Piston
91489
3 x 27.5
Shock Shaft
(front)
91490
3 x 35
Shock Shaft
(rear)
6299
1/8 E-Clip
6299
1/8 E-Clip
Racers Tip:
Use a marker over the
numbers on the pistons to
make them easily visible!
Build x2 (right and left side)
Racers Tip:
Use black grease
(#6588) on the
threads of the
turnbuckles for
easier ball cup
installation!
Front Camber Turnbuckle
23.00mm
91469
Ball Cup
91469
Ball Cup
91723
Turnbuckles,
3x48mm
Orient the notch
to the left throughout the
car. It indicates which end
has the left hand threads!
!
Build x2 (right and left side)
Racers Tip:
Use black grease
(#6588) on the
threads of the
turnbuckles for
easier ball cup
installation!
Rear Camber Turnbuckle
23.50mm
91469
Ball Cup
91469
Ball Cup
91723
Turnbuckles,
3x48mm
Orient the notch
to the left throughout the
car. It indicates which end
has the left hand threads!
!

16
:::: Shocks Build - Step 3Shocks Build - Step 3
:::: Shocks Build - Step 4Shocks Build - Step 4
:::: Shocks Build - Step 2Shocks Build - Step 2
Front Shock: 30wt
Rear Shock: 30wt
Step 9-10
Stroke
Front: 26.0mm
Rear: 35mm
Free Length
Front: 86.25mm
Rear: 103.50mm
Free
Length
Stroke
Stroke
Step 1-3 Step 3-4 Step 5-6 Step 7
Shock Bleeding Steps:
1. Pull shock shaft down.
2. Fill shock body 3/4 full with silicone
fluid.
3. Slowly move the shock shaft up and
down to remove air from under piston.
4. Wait for bubbles to come to surface.
5. Fill shock body to top with silicone fluid.
6. Place a drop of oil in the cap and on
cap threads.
7. Install cap and tighten completely.
8. Slowly compress shaft all the way to
the top. If there is pressure at the top
of the stroke, there is too much oil or
air. You must bleed it out.
9. Slowly pull shaft out.
10. Unscrew the cap 3/4 turn and tilt the
shock at a slight angle.
11. Slowly compress the shaft to push
out excess oil and air. You should see
bubbles coming out from under the
cap.
12. With the shaft compressed, tighten
the cap and re-check for pressure at
the top of the stroke. If there is still
pressure, repeat steps 9 thru11.
Shock fluid
#5422
Shock fluid
#5422
91454
Shock Cap
(Molded)
Front
Shocks None 5mm
Rear
Shocks
Pre-Load
Spacers
1mm
2mm
3mm
5mm
91636
12mm front
spring (54mm),
White (4.10lb)
91639
12mm rear
spring (72mm),
Green (2.20lb) Build x2 front and x2 rear shocks
#1105
green slime
91469
Shock
eyelet
91469
Shock
Pivot Ball
71051
Shock Body
12 x 27.5mm
(front)
71052
Shock Body
12 x 36mm
(rear)
91444
Shock
Internals
5407
O-Ring
91454
Shock
Bottom Cap
31327
Shock
Bottom Cap
O-Ring
91491
Shock Cap
O-Ring
x2x2
Lightly rub shock oil
on the o-ring before
installation!
!
!
71054
Pre Load
Spacers
91454
Spring
Cup
71054
Spring
Collar
#1105
green slime
Racers Tip:
Coating the o-rings
with green slime
(#1105) helps seal
& reduce o-ring
swell! Green slime
not included in kit!
71086
6mm Spacer
(Rear Only)

17
:::: Electronics Build - Step 1Electronics Build - Step 1
:::: Electronics Build - Step 2Electronics Build - Step 2
:::: Shocks Build - Step 5Shocks Build - Step 5
Build x2 (right and left side) Build x2 (right and left side)
91469
Steering
Link
Servo
71047
Servo
Saver
25201
M3 x 8mm
FHCS
91047
Heavy-duty
Ballstud, 6mm
Align the servo horn 90 degrees.
Adjust steering trim once vehicle is
complete.
!
!
89218
3x8mm
Washer
91391
Servo
Mount
31532
M3 x 8mm
BHCS
x4x4
x2x2
x4x4 x2x225201
M3 x 8mm
FHCS
Use outside
hole in
front arm!
!
Use outside
hole in
rear arm!
!
25612
M3 Locknut,
with flange
(black)
25612
M3 Locknut,
with flange
(black)
89202
M3 x 12mm
BHCS
91444
Shock
Bushing
91444
Shock
Bushing
25189
M3 x 22mm
BHCS

18
:::: Electronics Build - Step 4
:::: Electronics Build - Step 5Electronics Build - Step 5
:::: Electronics Build - Step 3Electronics Build - Step 3
* Receiver grommet
plug can be removed if
you use a personal
transponder!
* Install the ESC wires
and the Servo wires
into the wire grommet
before installing the
grommet into the
receiver box!
!
!
71023
Wire
Grommet
Plug
71023
Receiver Box
Grommet
71023
Receiver Box
Plug and
Grommet
71026
Receiver
Box
25211
M3 x 10mm
BHCS
71023
Belt Cover
Cap
91431
Gear
Cover
31530
M3 x 5mm
BHCS
x2x2
See page 23 for
gear mesh setting
instructions!
!
1336
Pinion Gear,
18T, 48P
25225
3 x 3mm
Set Screw
Motor
31532
M3 x 8mm
BHCS
x2x2
x2x2
89218
3 x 8mm
Washer

19
:::: Electronics Build - Step 6Electronics Build - Step 6
:::: Electronics Build - Step 7Electronics Build - Step 7
:: Bumper and:: Bumper and Chassis BracesChassis Braces Build - Step 1Build - Step 1
Receiver
71023
Receiver
Box Seal
71026
Receiver
Box Lid
25211
M3 x 10mm
BHCS
x2x2
6727
Servo Tape
25225
M3 x 3mm
Set Screw
6338
Antenna
Tube & Cap
Battery
not included!
71050
Hook and
Loop Straps 71197
Battery
Foam Spacer
x2x2 ESC
6727
Servo Tape
71041
Pro SC10
Front Skid
Plate
71041
Front
Bumper
Brace
89202
M3 x 12mm
BHCS
25203
M3 x 12mm
FHCS
x2x2
x2x2
25204
M3 x 16mm
FHCS
x2x2

20
:: Bumper and Chassis BracesChassis Braces BuildBuild - Step 2
:: Tires and Body Build - Step 1:: Tires and Body Build - Step 1
:: Tires and Body Build - Step 2
Build x4
Clean the tire and wheel bead.
Carefully apply CA glue (tire ad-
hesive) to the tire bead on both
sides. Do one side at a time,
allow it to dry before
gluing the other side!
CA glue not included!
#1597
ca glue
#1597
ca glue
!
91738
M4 Locknut,
with flange
and knurl
21173
Small
Body Clips
72117
Pro2 LT10 SW
Body, White
72117 - Pro2 LT10 SW Body, White
72118 - Pro2 LT10 SW Body, Clear
x4x4
x4x4
71042
Rear Bumper
(PRO SC10)
71042
Rear Bumper
Brace
(PRO SC10)
71042
Rear Bumper
Pivot
(PRO SC10)
91478
M3 x 30mm
BHCS
89204
M3 x 24mm
BHCS
25187
M3 x 14mm
BHCS
x4x4
72113
Tire, Insert,
and Wheel
Front
72112
Tire, Insert,
and Wheel
Rear