Astral Pool CONTROL BASIC PLUS User manual

Code 0000138008 rev 1.0
EN
DE
ES
FR
IT
PT
CONTROL BASIC PLUS ASTRALPOOL
INSTRUCTIONS MANUAL
HANDBUCH
MANUAL DE INSTALACION
MANUEL D’INSTALLATION
MANUALE D’INSTALLAZIONE
MANUAL DE INSTALAÇÃO

Code 0000138008 rev 1.0

Code 0000138008 rev. 1.0
1
CONTROL BASIC PLUS ASTRALPOOL
PACK CONTENTS
A) "Basic ASTRALPOOL" pH / REDOX control device
B) PVC Crystal 4x6 with suction device (2 m)
C) Polyethylene delivery hose (3m)
D) Attachment screw (f=6 mm)
E) Foot filter (PVC riser)
F) FPM duckbill valve (3/8” GAS)
G) ModBus connector
Wall Mounting Setup
TECHNICAL SPECIFICATIONS
Dimensions (H – W – L) 234x162x108 mm
Weight 1 kg
Power supply 50 Hz 230 VAC
Consumption 12 W or 18 W
Pump flow rate 1,5 l/h; 5 l/h
Maximum back-pressure 1,5 bar
Pump state Pause - Supply
Measure scale 0 ÷ 14.0 pH; Redox 0÷ +1000 mV
Device precision ± 0,1 pH; ± 10 mV
Device accuracy ± 0,02 pH; ± 2 mV
Electrode regulation Automatic
ATTENZIONE / WARNING / ATTENTION / ACHTUNG
G

Code 0000138008 rev. 1.0
2
Instruction Setting
Functions:
• Calibration
o (Press for 3 Seconds):
o Standard Routine calibration for 7 and 4 buffer solution
• Set Point
o Press
§ Keep Press Set Key and adjust value with
§ Sp_7.4ph
• Press for 5 Seconds and run Program Setup:
o Program
§ Press to set the following Item
• PUMP Config.
§ Adjust pH or Redox
• Language
§ (It’s possible to have 5 language EN, IT, SP, DE, FR
§ dosage type
§ Adjust value with and
• It’s possible to adjust value between PROP or ON/OFF
• Flow
§ Adjust value with and
• It’s possible to enable(ON) or disable (OFF) signal input
• rs485 settings
Press to set the following Item
§ rs-485
• Adjust value with and

Code 0000138008 rev. 1.0
3
• It’s possible to enable(ON) or disable (OFF) the communication.
§ wdg config.
• Adjust value with and
• It’s possible to set as: Hardware Reset, Com. Reset, Stop Dosage and
WDG Alarm (default value).
§ rs485 watchdog
• Adjust value with and
• It’s possible to adjust the time in seconds. If it is set as OFF (default value)
the communication watchdog is disabled.
§ address
• Adjust value with and
• It’s possible to adjust the address of the device from 1 (default value) to 247
§ parity
• Adjust value with and
• The value of the parity bit, it’s possible to set as: Even (default value), Odd
or No.
§ baudrate
• Adjust value with and
• The value of the speed of the transmission, it’s possible to set as: 2400,
4800, 9600 (default value), 19200.
•
o Setpoint 7.4ph
o Adjust value with and
§ It’s possible to adjust from 0 to 14 pH value and 0 to 1000 mV for Redox
o Setpoint Type Acid
§ Adjust value and
§ It’s possible to adjust Acid or Alkaline dosing and High or Low for Redox
o OFA Time off
§ Adjust value and
§ It’s possible to adjust OFA time in minutes

Code 0000138008 rev. 1.0
4
o Calibration 7/4pH
§ Adjust value and
§ It’s possible to select 2 points 7 and 4 pH, 1 point only 7pH or function disable; for
Redox function disable only.
o Man Temperature 25
°
C
§ Adjust value and
§ pH measure only.
• Save and escape Program setup with ESC key
o Exit save
§ Adjust value with up or down key and confirm with
o Priming
• Priming Pump Keep Press for 3 seconds
Wire Connection:
1) Input pH or Redox Probe
2) Input Temperature Probe (PT100)
3) Input Level Probe (Product Tank)
4) Input Flow Rate (High Voltage 230 Vac)
5) Output Relay Alarm remote (Dry contact,
Relay 250 Vac 10 A)
6) Output Relay Drive Solenoid Valve (Dry
contact, Relay 250 Vac 10 A)
7) Power Supply 230 Vac
8) Switch Power Supply
9) Connection to a chlorine generator (example)
10) Port connection for the ModBus communication
ModBus connetion
Pin N°
Description
1
T+R+ (B)
2
T-R- (A)
3
GND
4
Not used
1
2
3
4
5
6
7
8
CHLORINE
GENERATOR
250 V/50 A
REMOTE CONTROL
SWITCH
(NOT INCLUDED)
230 Vac
F
N
9
10

Code 0000138008 rev. 1.0
5
pH Probe Calibration
Wash
Keep probe into Buffer solution
Calibration
Press Cal Key 3 Seconds
5
7pH___Press_CAL
Calibration During 1 minutes
Wait________60s
6
7pH_Quality_100%
Quality Probe
7
Wash
Keep probe into Buffer solution
4pH___Press_CAL
Calibration During 1 minutes
Wait________60s
10
4pH_Quality_100%
Quality Probe
11
Wash
Press Enter Key to save and exit
14
Normal Status
15
Note:
If you have setting Calibrabration = 7 pH the function has 1 point calibrate only 7 pH buffer solution.

Code 0000138008 rev. 1.0
6
Redox Probe Calibration
Wash
Keep probe into Buffer solution
Calibration
Press Cal Key 3 Seconds
5
465mv___Press_CAL
Calibration During 1 minutes
Wait________60s
6
465mv_Quality_100%
Quality Probe
7
Press Cal Key 3 Secondù
10
Normal Status
11

Code 0000138008 rev. 1.0
7
Alarm
Display
Relay
Actions to do
Level
Level____7,2_ph
Alarm Relay
Close
- Push Enter Key to open
Alarm Relay
- Restore Product tank
OFA First Alarm (time >70%)
OFA_Alarm__7,2_ph
Alarm Relay
open
- Push Enter Key to reset
OFA Second Alarm (time =100%)
OFA_STOP___7,2_ph
Alarm Relay
Close
- Push Enter Key to reset
Flow Rate
Flow_______7,2_ph
Alarm Relay
open
- Restore Flow Rate
System Error
Parameter_Error
Alarm Relay
Open
- Press Enter Key to replace
Default parameter
Communication Watchdog alarm
Wdg_Alarm
Alarm Relay
Close
- Check the communication
network
Calibration Function
Error_7_ph
Error_4_ph
Error_465_mV
Alarm Relay
open
- Restore Probe or Buffer
solution and repeat calibration
function
To restore Default parameters run Following steps:
•Power off Pool Basic unit
•Keeping Press UP and DOWN Key switch on the
Power.
•The unit will flash Init.default__no
•Press up Init.default__Yes
•Enter Key to restore Default parameters.
Default parameters:
•Language = UK
•Set Point value= 7,4 pH; 750mV (Rx)
•Dosing Method = Acid; Low (Rx)
•Time OFA = OFF
•Calibration = 7/4 (2 point); 465mV (Rx)
•Flow Input = OFF

Code 0000138008 rev.1.0
1
CONTROL BASIC PLUS ASTRALPOOL
Verpackungsinhalt
A) "Basic ASTRALPOOL" pH / REDOX Kontrollsystem
B) PVC-Schlauch Crystal 4x6 (2 m)
C) Polyethylen-Schlauch (3 m)
D) Schrauben mit Dübeln (f = 6 mm)
E) Fußfilter (PVC)
F) Rückschlagventil aus FPM (3/8” GAS)
G) ModBus-Anschluss
Wandmontage
TECHNISCHE DATEN
Abmessungen (H - B - T) 234x162x108 mm
Gewicht 1 kg
Spannungsversorgung 230 Vac
Verbrauch 12 W oder 18 W
Förderleistung der Pumpe 1,5 l/Std.; 5 l/Std.
Max. Gegendruck 1,5 bar
Pumpenstatus Pause - Betrieb
Messskala 0 ÷ 14.0 pH; Redox 0 ÷ +1000mV
Messgenauigkeit ± 0,1 pH; ±10 mV
Genauigkeit Maß ± 0,02 pH; ±2 mV
Kalibrierung der Elektrode automatisch
ATTENZIONE / WARNING / ATTENTION / ACHTUNG