AT&T Merlin II Feature Module 2 User manual

AT&T
MERLIN
®
II
COMMUNICATIONS SYSTEM
Feature Module 2
User’s Guide:
Basic Touch-Tone and Rotary Telephones

©1988 AT&T
All Rights Reserved
Printed in USA
Issue 2
May, 1988
NOTICE
The information in this document is subject to change without notice. AT&T assumes no
responsibility for any errors that may appear in this document.
MERLIN is a registered trademark of AT&T.
To order copies of this document, call the AT&T Customer Information Center, 1-800-432-6600 and
include the document number 999-503-140 with your order.

Table of Contents
Introduction
2
Placing Intercom Calls
3
Dialing Outside Calls
4
Dialing Outside Calls in Systems
with Special Features
6
Placing Calls with Speed Dialing Features 8
Answering Calls
10
Paging Co-workers
12
Handling Calls with the Hold
and Transfer Features
13
Setting Up a Conference Call
14
Receiving Messages and Reminders
15
Notes
16

Introduction
About This Guide
This guide shows how to handle calls and use features of
the MERLIN II system. The MERLIN II System Manual
provides complete information about system features and
equipment.
About Your Telephone
You may have either a rotary or a Touch-Tone telephone.
You can place, answer, and handle calls on either phone,
but some optional system features require Touch-Tones.
The Switchhook
Switchhook
The switchhook serves two functions:
●
●
Holding the switchhook down for several seconds
disconnects the call.
Pressing the switchhook, then releasing it (a switchhook
flash), sends a signal to the MERLIN II system control
unit. You use the switchhook flash to put calls on
hold, transfer them, and set up conference calls.
Touch-Tones
If you have a Touch-Tone phone, you can send signals to
the control unit by touching buttons on the dial pad.
When you dial # or *, then dial one of the codes shown
in this guide, the system recognizes the digits you dial as
a feature code rather than part of a telephone number.
Your administrator assigns optional features to your
telephone. Ask him or her which features you can use.
[TT]This symbol indicates that the feature works
with Touch-Tone telephones only.
Dial Tones
There are two dial tones:
● Intercom dial tone
● Outside line dial tone
When you first lift your handset, you hear the intercom
dial tone. You have to dial a code to get the outside line
dial tone.
2

Placing Intercom Calls
You can call anyone in the MERLIN II system by dialing
his or her intercom number. You can call Call
Distribution groups (groups of people, such as sales
representatives, who answer incoming calls on a round-
robin basis) by dialing the group code.
To place an intercom call:
1 Lift your handset.
2 Dial the intercom number or the Group Call
Distribution code.
If you don’t have a list of intercom numbers and Group
Call Distribution codes for your system, see your
administrator.
Introduction
Intercom Calls
3

Dialing Outside Calls
System Type
How you place calls depends on what type of MERLIN II There are three types of pooled systems:
system you’re using. Ask your administrator, then ❑ With Button Access
check the appropriate box.
Outside line representation on this system is: ❑ With Dial Access
❑ Square ❑ With Automatic Route Selection (ARS)
❑ Pooled
Placing Calls
Ask your administrator what lines or line pools are
assigned to your telephone and follow the appropriate
steps, below.
Placing calls in a square system:
1 Lift your handset.
2 Dial 88.
You hear the outside dial tone.
3 Dial the telephone number.
NOTE: Ask your administrator if you have to enter an
account code before you dial an outside call. If you do,
see “Forced Account Code Entry,” below.
Placing calls in a pooled system with Button
Access or ARS:
1 Lift your handset.
2 Dial 9.
You hear the outside dial tone.
3 Dial the telephone number.
4

Placing calls in a pooled system with Dial Access:
1 Lift your handset.
2 Dial 9.
3 Dial the appropriate line pool access code. (If you
don't have the codes, ask your administrator.)
You hear the outside dial tone.
4 Dial the telephone number.
Placing calls on a personal line in a pooled system:
1 Lift your handset.
2 Dial 88.
You hear the outside dial tone.
3 Dial the telephone number.
Outside
Calls
5

Dialing Outside Calls in Systems with Special Features
NOTE: If you can’t dial calls after regular business hours,
your system may have Night Service with Outward
Restriction. If you need to make business calls while
Night Service is in effect, see your administrator.
Forced Account Code Entry [TT]
If your telephone is administered for Forced Account
Code Entry, you must dial an account code whenever
you place an outside call.
To make an outside call:
1 Lift the handset.
You hear the intercom dial tone.
2 Dial #22.
3 Dial the account code (maximum of 16 characters).
4 Dial #22.
5 Access the line or line pool you want tp use for the
call.
You hear the outside dial tone.
6 Dial the telephone number.
6

Privacy [TT]
The Privacy feature prevents people who share your
To make a private call:
lines from joining your conversation. Be sure to 1 Lift the handset
deactivate the feature when you don’t need it any
You hear a dial tone.
longer.
2 Dial #31 to turn Privacy on.
3 Hang up your handset when you’ve finished.
4 Lift the handset
You hear a dial tone.
5 Dial #30 to turn Privacy off.
Account Code
7
Privacy

Placing Calls with Speed Dialing Features
If your administrator has assigned speed dialing features
to your telephone, you can use codes for quick dialing of
outside calls and for redialing numbers.
Personal Speed Dial [TT]
Your administrator can assign codes #01 through #21 to:
Telephone numbers you dial often
Account numbers
MERLIN II system features
PBX, Centrex, or Custom Calling features.
To place a Personal Speed Dial call:
Get the Personal Speed Dial codes from your
administrator and follow these steps to place a call.
1 Lift your handset.
2 Dial the Personal Speed Dial code.
8