Atdec AV Cart 20 User manual

AD-TVC-20 Page 1 of 4
Installation Guide
AD-TVC-20
AV Cart 20
COMPONENT CHECKLIST
REQUIRED TOOLS
A
Column (x1)
B
Base Leg (x2)
C
Base Crossbar (x1)
D
Rail (x1)
E
Left Display
Bracket (x1)
F
Right Display
Bracket (x1)
G
AV Shelf
(x1)
H
AV Shelf
Bracket (x1)
I
Column Base
Cover (x1)
J
Castor
(x4)
K
Base Leg Cover
Left (x1)
L
Base Leg Cover
Right (x1)
M
Cable
Cover
(x2)
N
M6X50
Screw
(x4)
O
M6X35
Screw
(x4)
P
M6X16
Screw
(x11)
Q
Washer
(x8)
R
Column Top
Cover (x1)
S
5mm Allen
Key(x1)
T
M8 + M10
Wrench
(x1)
M-A
M5X14
Screw
(x4)
M-B
M6X14
Screw
(x4)
M-C
M6X30
Screw
(x4)
M-D
M8X30
Screw
(x4)
M-E
M8X50
Screw
(x4)
M-F
Multi
Washer
(x4)
M-G
Small
Spacer
(x8)
M-H
Large
Spacer
(x8)
• Phillips Head Screwdriver
CAPACITY
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! Failure to assemble this product correctly may cause serious injury/death during or following installation.
! This product should only be installed by professional installers of good mechanical aptitude, who fully understand these instructions and the
consequences of incorrect installation.
! Do not over tighten screws.
! Two person installation is recommended.
! Product not suitable for use outdoors.
! After installation is complete check to verify that AV Cart is secure and safe for use.
! Curved monitors, deep devices (such as all-in-one PCs), VESA mounted accessories (such as mini PC brackets and mounts), and offset VESA
locations exert additional leverage that can exceed the capacity of the mount even though the monitor weight may be within the stated range.
Please contact Atdec if you would like further information.
! WARNING! Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or toys placed on
the cart may encourage a child to climb on the cart and as a result the cart may tip over on to the child.
DISPLAY
0 - 20kg (0 - 44lb)
32” - 55”
SHELF
0 - 5kg (0 - 11lb)

AD-TVC-20 Page 2 of 4
1. Assemble base
T
P
O
S
C
B
J
L
K
Note: Lock brakes on castors to avoid
any sudden movements during installation.
T
P
O
S
C
B
J
L
K
Note: Lock brakes on castors to avoid
any sudden movements during installation.
1.1 1.2
WARNING!
! DO NOT ALLOW CHILDREN UNDER 16 TO PLAY WITH OR MOVE CART
! MOVE CART SLOWLY
! USE WITH DISPLAYS HEAVIER THAN SPECIFIED MAY RESULT IN INSTABILITY, TIP OVER AND RISK OF
DEATH OR SERIOUS INJURY
DO NOT PULLNEVER APPLY FORCE
AT TOP
APPLY FORCE ON
NARROW SIDES
PUSH NEAR MIDDLE
DO NOT APPLY
MOVING FORCE ON
FRONT OR BACK
ONLY ADULTS SHOULD
MOVE THIS CART
LOCK
BRAKES WHEN
STATIONARY
UNLOCK
BRAKES BEFORE
MOVING
DO NOT PULL
NEVER APPLY FORCE AT
TOP
APPLY FORCE ON
NARROW SIDES
PUSH NEAR MIDDLE
DO NOT APPLY MOVING
FORCE ON FRONT OR
BACK
ONLY ADULTS SHOULD
MOVE THIS CART
LOCK
BRAKES WHEN
STATIONARY
UNLOCK
BRAKES BEFORE
MOVING
3. Attach column to base
A
I
Q
N
1
2. Extend column to maximum height
Without releasing the
spring latch, slide the
upper part of the column
out slowly.
Note: Do not attempt to
pull the upper part of the
column out beyond the
MAX indicator.
Make sure the spring latch
is fully pressed in before
letting go of the upper
part of the column.
1
1
1
2.1 2.2 2.3
Whilst resting the base of
the column on the oor,
rmly hold the upper part
of the column and pull the
spring latch out.

AD-TVC-20 Page 3 of 4
5. Attach rail to column
6. Attach shelf to column
IMPORTANT
Safety Screw
Q P
D
P
G
H
4. Finish column assembly
R
M
P
7. Attach display brackets to display
F
EM-A
M-F
M-B
M-F
E
F
M-G
M-H
M-F
M-C
M-D
M-F
M-E
F
EM-A
M-F
M-B
M-F
E
F
M-G
M-H
M-F
M-C
M-D
M-F
M-E
F
EM-A
M-F
M-B
M-F
E
F
M-G
M-H
M-F
M-C
M-D
M-F
M-E
F
EM-A
M-F
M-B
M-F
E
F
M-G
M-H
M-F
M-C
M-D
M-F
M-E
Note:
• Always use a multi washer.
• Use the shortest combination of spacers (if necessary) ensuring the display
bracket is not loose and screws are not forced too deep into the display.
Note: Ensure rail is centred to column before tightening screws.

AD-TVC-20 Page 4 of 4
Display MUST be removed prior to adjusting height.
+10°
-10°
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specications without notice. ©20210330
ADJUSTMENTS
MAINTENANCE
8. Mount display on rail and secure 9. Route cables
• Tighten fasteners and check if the cart is secure and safe to use at regular intervals (at least every three months.)
• Please contact your distributor if you have any questions.
Forwards/backward tilt Height adjustment (see step 2)
IMPORTANT: Spring latch cannot be released with display mounted.
1. 2. 3.
Note: Ensure display is centred to column
before tightening screws.