Atdec 5060 User manual

AD-WT-5060 Page 1 of 2
REQUIRED TOOLS
• Phillips head screwdriver
• Power drill
• Suitable drill bit
• Driver bit for selected
wall fasteners
• Stud nder
• Spirit level
Installation Guide
AD-WT-5060
Tilt Wall Mount 5060
A
M5x14 (x4)
Screw
D
Multi
Washer
(x4)
H
XX (x4)
I
XX (x4)
G
Spirit
Level
(x1)
E
Short
Spacer
(x8)
F
Long
Spacer
(x8)
G
XX (x4)
B
M6x14 (x4)
M6x30 (x4)
Screw
C
M8x30 (x4)
M8x50 (x4)
Screw
H
Wall Plate
I
Display Bracket (left)
J
Display Bracket (right)
IMPORTANT INFORMATION
! Please ensure this product is installed as per these installation instructions.
! The manufacturer accepts no responsibility for incorrect installation.
! Failure to mount this product correctly may cause serious injury/death during or following installation.
! This product is not suitable for outdoor use.
! Do not use this product for mobile applications.
! This product supports a maximum load of 50kg (110lb).
! Wall Plate only achieves maximum weight rating when appropriately fastened to a wall of adequate structural capacity.
! Professional installer to ensure adequate structural capacity of wall (including appropriate safety factor) to support total
weight of all equipment being mounted.
! Drilling into electrical wires can cause death - use appropriate equipment and caution when drilling holes in walls to avoid
electrical cables, water pipes and gas pipes. Do not drill into structures unless you have established it’s safe to do so.
! Suits displays with mounting hole patterns from 75mm to 620mm wide by 70mm to 405mm high.
COMPONENT CHECKLIST
0 - 50kg
(0 - 110lb)
WEIGHT RANGE
NOTE:
! Wall Plate Mounting Fasteners are NOT supplied with Wall Mounts. Professional
installer to ensure correct Mounting Fastener type, location & quantity to suit
structure where Wall Mount is installed.
! ALWAYS use a washer between the chosen fastener and the wall plate.
! Mounting fasteners to be used as per manufacturers instructions, including
minimum engagement to achieve necessary performance.

AD-WT-5060 Page 2 of 2
J
G
Slot Dimension
Ø8 x 40mm
12 3
*Fasteners shown are not included
B (M6X30) /
C (M8X30)
B (M6X30) /
C (M8X30)
D
E
D
F
F
E
D D
F
F
EE
D
F
D
B (M6X30) /
C (M8X30)
C (M8X50) C (M8X50) C (M8X50)
A (M4x14) /
B (M6X14)
D
No portion of this document or any artwork contained herein should be reproduced in any way without
the express written consent of Atdec Pty Ltd. Due to continuing product development, the manufacturer
reserves the right to alter specications without notice. ©20210813
3. Hook the Display onto the Wall Plate 4. Secure the Display and Lock Tilt Angle
-5°
+10°
-5°
+10°
NOTE:
Ensure security screw is loosened before attempting to
mount display.
NOTE:
Support display whilst tightening security screws and
adjusting tilt.
1. Mount the Wall Plate to the Wall
3.1. Angle the display and hook the Display
Brackets over the top of the Wall Plate. This
should be completed by two people.
4.1. Use a Phillips head screwdriver to tighten the security
screw on each Display Bracket, ensuring the screw sits to
the rear of the Wall Plate and the display cannot be lifted
up and off the Wall Plate.
4.2. Tilt the display to the desired viewing angle and tighten
the screw knob to lock the angle in place.
NOTE:
• Choice and supply of appropriate wall plate fasteners is the
responsibility of the installer.
• Consult a preferred fastener supplier or a structural engineer to
select fasteners which are most appropriate for the weight of
the display and wall construction method.
• Wall plate must be level. Verify using a quality spirit level tool
or the included spirit level G.
• On a Stud Wall or Drywall use a good quality Stud Finder to
position mounting fasteners in the centre of studs.
• On a Masonry Wall avoid positioning Wall Plate mounting
fasteners in a mortar join.
NOTE:
• Always use multi-washers D.
• Use the shortest combination of spacers (if necessary) ensuring the
display is not loose and screws are not forced too deep into the display.
2. Attach the Display Brackets to the Display