Atdec AW-ORA-F User manual

Ora Monitor Arm F-clamp
Installation Guide
AW-ORA-F
COMPONENT CHECKLIST
VESA Plate (x1)
Upper Link (x1)
Lower Link (x1)
F Clamp (x1)
4mm
Hex Key
(x1)
M4x10
Screw
(x4)
Security
Screw
(x1)
Hardware & Tools
CAPACITY
IMPORTANT INFORMATION
•Install Ora Monitor Arm as per these installation
instructions.
•The manufacturer accepts no responsibility for
incorrect installation.
•Do not over-tighten screws and adjustment points on
product.
•This product is not suitable for outdoor use.
•Do not use this product for mobile applications.
•Please ensure desk structure and mounting surface
are of sufficient strength to support this product and
mounted equipment.
•Deep devices (such as all-in-one PCs), VESA mounted
accessories (such as mini PC brackets and mounts),
and offset VESA locations exert additional leverage
that can exceed the capacity of the mount even
though the monitor weight may be within the stated
range. Please contact Atdec if you would like further
information.
•Suits displays with VESA mounting hole patterns
75x75 and 100x100. Spacer kit (sold separately) may
be required for recessed 75x75 hole patterns.
•For edge clamp Installations, ensure the monitor is
always positioned over the work surface. Do not
position the monitor beyond the rear edge of the
work surface.
•Periodic adjustment to counterbalance and tilt tension
may be required.
No portion of this document or any artwork contained herein should be
reproduced in any way without the express written consent of Atdec Pty
Ltd. Due to continuing product development, the manufacturer reserves
the right to alter specifications without notice. ©20230210
2 - 8kg (4.4 - 17.6lb)
Up to 35” (curved or flat)
(Larger monitors within the weight
capacity may be compatible, please
contact Atdec for advice).
Weight:
Display Size:
WARRANTY
TOOLS REQUIRED
10 Years Limited
Phillips head screwdriver

Configure F Clamp for desk thickness
1 Attach F-clamp to Desk
OR
1.1
0 - 35mm
(0 - 1 ⅜”)
Standard Desks
35 - 70mm
(1 ⅜ - 2¾”)
Thicker Desks
Re-tighten
2x screws
Alternative Fixing Options
Ora Bolt Through
Fixing AW-FB
(sold separately)
Position clamp on
edge of work surface
IMPORTANT
Ensure clamp
is pushed up
against work
surface edge
1.2
1.3
NOTE
Bevelled edges
not compatible
TIP
When positioning the desk clamp, offset the
clamp to the left or right of the seating position.
The monitor will then be centred for the user.
100mm
(4”)
Tighten firmly
by hand or
using 4mm
hex key
1.4
HINT!
IMPORTANT
Ensure metal
washer is in
place on the tip
of the screw
Hook on lower bracket
and re-tighten 2x screws
If the gap behind the work surface is less than
70mm (2¾”), unhook the lower bracket and
reattach it from under the desk.

2 Attach Lower Link to Clamp
2.1
2.2
2.3
360°
Select rotation
360°
180°
360°
180°
360°
180°
180°
NOTE
Pivot lower link to the forward
position shown in Step 2.2
before selecting 180˚ rotation.
OR
PRESS
DOWN
IMPORTANT
Ensure plastic sleeve
is fitted on lower link
3 Attach Upper Link
3.1
Using the 4mm hex
key, tighten set screw
until joint rotation is
firm and smooth
3.3
3.4
Press down firmly to
ensure the upper link
is fully located onto
the lower link
PUSH DOWN
AND HOLD
3.2
CAUTION!
Check Cover Strip
To inspect cover
strip, fully lower the
upper link . If
damaged or missing,
stop installation and
contact Atdec for
assistance.
Attach VESA Plate using
supplied M4x10 screws.
Attach monitor
to arm
4 Mount Monitor
4.1
4.2
100mm
75mm
100mm
75mm
4.3
Click
NOTE
Recessed 75x75mm
VESA interfaces will
require a spacer kit
(sold separately)
Check VESA mounting
compatibility of monitor
NOTE
For other sizes, use
suitable adaptor plate
(sold separately).
Ensure screw length
suits the monitor
TOO
LONG
OK
TOO
SHORT

5 Adjustments
5.1 Tilt Tension
5.2 Monitor Rotation Tension (optional)
Adjust rotation tension
using 4mm hex key.
NOTE
Adjustment may
only be required
for ultrawide
monitors
HOLDS POSITION
HOLDS POSITION
DRIFTS
DROOPS FORWARD
TIGHTEN
TIGHTEN
LOOSEN
LOOSEN
If required, adjust tilt
tension using 4mm
hex key. (do not
over-tighten)
NOTE
Support the
screen while
adjusting
5.3 Counterbalance Adjustment
Increase
tension
Reduce
tension
TIP
For best results,
adjust
counterbalance
with the arm and
monitor in the
position shown.
Adjustment is
easiest when the
monitor is in the
highest position.
TIP
When installing multiple arms with the same monitor,
use the setting on the counterbalance adjustment
gauge to quickly ‘pre-set’ other arms (fine-tuning may
be required after pre-setting).
Using the 4mm hex key,
adjust counterbalance
to suit the monitor
weight
DROOPS BOUNCES UP HOLDS
POSITION
COUNTER-
BALANCE
ADJUSTMENT
SCREW
COUNTER-
BALANCE
ADJUSTMENT
GAUGE
Lighter
Monitors
Heavier
Monitors
5.4 Security Screw (optional)
If desired, once
monitor is
attached to the
arm, install the
security screw.
This disables the
release switch,
preventing theft.
Do not position monitor beyond the rear edge
of the desk.
Click
SLIDE
5.5 Removing Monitor
5.6 Positioning
LIFT

6 Cable Management
6.1 Overview
NOTE
Ensure enough cable
slack is given to
allow for movement
of the monitor
NOTE
Allow 1.2m of cable from the work surface to the
monitor. Add additional cable length to route the
cable from the work surface to the computer.
Go to
6.4
Go to
6.3
If desired,
store hex key
in lower link
6.2
PULL
6.3 Route Cables Through Upper Link
S
L
I
D
E
S
L
I
D
E
NOTE
Ensure cables do
not interfere with
sliding cover on.
TUCK
TUCK
Tuck cables behind
tabs inside lower link.
6.4
SLIDE
Remove lower link
cable cover.
6.6
SLIDE
Re-attach lower link
cable cover.
6.5