Atlas Copco RTX-14 User manual

RTX-14
TORQUE CHART
This chart shows the correlation
between pump gauge psi reading
and torque output for your Rapid-Torc
RTX-14 hydraulic torque wrench.
PSI FT.LB.
1500 2010
1600 2144
1800 2412
2000 2680
2200 2948
2400 3216
2600 3484
2800 3752
3000 4020
3200 4288
3400 4556
3600 4824
3800 5092
4000 5360
4200 5628
4400 5896
4600 6164
4800 6432
5000 6700
5200 6968
5400 7236
5600 7504
PSI FT.LB.
5800 7772
6000 8040
6200 8308
6400 8576
6600 8844
6800 9 11 2
7000 9380
7200 9648
7400 9916
760 0 10184
7800 10452
8000 10720
8200 10988
8400 11256
8600 11524
8800 11792
9000 12060
9200 12328
9400 12596
9600 12864
9800 13132
10000 13400
BAR NM
104 2725
110 2907
124 3270
138 3634
152 3997
165 4360
179 4724
193 5087
207 5450
220 5814
234 6177
248 6540
262 6904
276 7267
290 7631
303 7994
317 8357
331 8721
345 9084
358 9447
372 9811
386 10174
BAR NM
400 10537
414 10901
427 11264
441 11627
455 11991
468 12354
482 12718
496 13081
510 13444
524 13808
538 14171
552 14534
565 14898
579 15261
593 15624
607 15988
620 16351
634 16715
648 17078
662 17441
676 17805
690 18168
2
Set the pressure on the pump that
corresponds to the torque value.
1Find the closest torque value for
your application, either in ft-lbs
or in Nm.
FOOT-POUNDS NEWTON-METERS
The above torque values are only applicable when using a calibrated RTX-14 hydraulic torque wrench powered by a 10,000 psi
pump fitted with a calibrated class 1 gauge.
RT-PTCen-RTX-14 Copyright Rapid-Torc®. Part of the Atlas Copco Group Revised October 2014

QUICK SETUP
GUIDE
Setting up your hydraulic torque wrench for use is easy.
Please read the included user manual and safety instruc-
tion booklet for additional guidelines.
1
FOUR BASIC STEPS TO OPERATE YOUR RTX-14
4
Scan the code to see a brief overview video on how to use the document or go to
rapidtorc.com/torque_setup
RT-PTCen-RTX-14 Copyright Rapid-Torc®. Part of the Atlas Copco Group Revised September 2014
Wear personal protec-
tive equipment, such as
eyeglasses and steel-toe
shoes.
1
2
3
SET PRESSURE
Make sure the hoses are
free of any defects. The
couplers are on pump
and the tool should be
securely connected.
Place tool on at surface.
Turn pump on. Cycle the
tool. Press the “ON’ but-
ton on the remote, hold
until tool clicks. Release,
wait for the tool to click.
Repeat the cycle. Ensure
there is no leak.
4
Use the torque conver-
sion chart to set the psi
for the torque you need.
Press the remote’s “ON”
button and slowly turn
the pressure regulator
clockwise to reach the
right pressure.
CYCLE YOUR TOOL
CONNECT HOSES
WEAR PPE
2
3