Atmel ATSAMB11 BluSDK SMART User manual

ATSAMB11 BluSDK SMART
AT Command - Getting Started Guide
USER GUIDE
Introduction
This document explains the details about:
Getting started with the setup of ATSAMB11 Xplained board
How to use AT Command on ATSAMB11 Xplained board
Features
Reset the link layer
Set device configuration
Start scan
Stop scan
Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]
Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016
2
2
Table of Contents
Introduction .....................................................................................................................1
Features .....................................................................................................................1
Table of Contents ........................................................................................................2
1Purpose .....................................................................................................................3
2Demo Setup..................................................................................................................4
3Hardware Setup ...........................................................................................................5
4Software Setup.............................................................................................................6
4.1 Installation Steps...................................................................................................................................6
4.2 Build Procedure.....................................................................................................................................6
5Running the Demo.......................................................................................................8
6BluSDK SMART Software Architecture....................................................................10
7ATMEL EVALUATION BOARD/KIT IMPORTANT NOTICE AND DISCLAIMER........11
8Revision History ........................................................................................................12

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]
Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016
3
3
1 Purpose
This getting started guide describes the setup of ATSAMB11 Xplained board and bringing up an AT CMD
example supplied as part of BluSDK Smart release.
The AT command set is listed in the following table.
Table 1-1. AT Command Set
Command
Command Description
Command Syntax
Reset
Reset the link layer
AT+RESET
Configuration
Set device configuration
AT+CFG_DEF
Start Scan
Start scan operation
AT+SCAN
Stop Scan
Stop an ongoing scan operation
AT+STOP

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]
Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016
4
4
2 Demo Setup
Figure 2-1. Demo Setup of the AT CMD Application on ATSAMB11
USB Cable
PC
AT Command Prompt
ATSAMB11
BLE Link

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]
Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016
5
5
3 Hardware Setup
Connect the ATSAMB11 board to the host PC using a Micro-USB cable.
Figure 3-1. EDBG USB Port

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]
Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016
6
6
4 Software Setup
4.1 Installation Steps
1. Install the latest Atmel Studio [Atmel Studio 7.0 (build 629 or later) web installer
(recommended)]
http://www.atmel.com/tools/ATMELSTUDIO.aspx.
2. Install the latest Atmel Software Framework.
This package will install the following examples within the Atmel Studio environment:
AT CMD application for ATSAMB11
4.2 Build Procedure
The following procedure is explained for ATSAMB11 application example.
1. Select New Example Project.
Figure 4-1. Creating a New Example Project
2. Select “SAMB11” in device family, enter “at cmd” in search window, and expand Atmel Corp
Projects. The location and the name of the project can be selected in the respective fields. Click
OK.
Figure 4-2. Selecting AT CMD Application from Example Projects
3. Accept the license Agreement. The Atmel studio will generate the AT CMD project for ATSAMB11.
4. Build the solution.

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]
Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016
7
7
Figure 4-3. Building the AT CMD Application
5. Download the application via the USB to the ATSAMB11 board by using the Device Programing
option available in Tools as shown below.
Figure 4-4. Flashing the Application on Atmel MCU
6. Inside the device programming the user has to select the correct configuration for the device and
finally program the device by using the program button.
Figure 4-5. Flash Programming
7. Once the application is flashed, now AT CMD Application is ready for usage.

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]
Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016
8
8
5 Running the Demo
Type one of four commands you want on the console.
1. Reset command
Type “AT+RESET” and then press ‘Enter’ key.
Figure 5-1. RESET command
UART Initialized
Device name : Atmel BLE Device
Device Address : 0xF8F005F35D67, Type : 0
>>BLE Stack Initialized, use “AT+” for AT-Commands
# CMD Handler Ptr.
-------------------------------------------------------
01 RESET 100108b9
02 SCAN 10010917
03 STOP 10010941
04 CFG_DEF 100108cf
-------------------------------------------------------
AT+RESET
Searching for CMD handler...
Processing...Reset Handler
DONE
2. CFG_DEF command
Type “AT+CFG_DEF” and then press ‘Enter’ key.
Figure 5-2. CFG_DEF command
AT+CFG_DEF
Searching for CMD handler...
Processing... Config Handler
DONE

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]
Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016
9
9
3. SCAN command
Type “AT+SCAN” and then press ‘Enter’ key. After a while, scan results should be shown as below.
Figure 5-3. SCAN command
AT+SCAN
Searching for CMD handler...
Processing... Scan Handler
DONE
AT_BLE_SCAN_INFO:
Device Addr.: 0xF8F005F35BE4
AddrType : 0x00
RSSI : -68
AT_BLE_SCAN_INFO:
Device Addr.: 0xF8F005F35BE4
AddrType : 0x00
RSSI : -66
AT_BLE_SCAN_INFO:
Device Addr.: 0xACEE9E19AE82
AddrType : 0x00
RSSI : -78
AT_BLE_SCAN_INFO:
Device Addr.: 0xF8F005F35978
AddrType : 0x00
RSSI : -77
AT_BLE_SCAN_INFO:
Device Addr.: 0xF8F005F35978
AddrType : 0x00
RSSI : -76
4. STOP command
Type “AT+STOP” and then press ‘Enter’ key.
Figure 5-4. STOP command
AT+STOP
Searching for CMD handler...
Processing... Stop Handler
DONE

ATSAMB11 BluSDK SMART –AT CMD –Getting Started Guide [USER GUIDE]
Atmel-42693A-ATSAMB11-BluSDK-SMART-AT-CMD-Getting-Started-Guide_UserGuide_032016
1
0
10
6 BluSDK SMART Software Architecture
Figure 6-1 illustrates the top level diagram for the BLU-SDK SMART configuration.
Figure 6-1. ATSAMB11 Software Architecture