Atop ABLELink EH2006 User manual

Atop ABLELink® Industrial Switch
ATOP® EH2006
ATOP® EH2005-Fs
ATOP® EH2005-Fm
5/6-port Industrial Switch
Quick Installing Guide
EH2006
EH2005-Fs
EH2005-Fm
Version 1.2
Updated on October, 2006
Tel: [phone]
Fax: [phone]
www.atop.com.tw

Quick Installing Guide Version 1.2
Atop ABLELink® Industrial Switch
EH2006/EH2005-Fs/EH2005-Fm
Copyright © 2006 ATOP Technologies, Inc.
All rights reserved
- 1 -
1. Introduction
Thank you for purchasing Atop EH Indusial Switch Hub. This document intends to
provide customers with brief descriptions about the product and to assist our
customers to get started.
2. Inside the Package
-Main Product
 EH2005-Fs/Fm or EH2006 Device
- Standard Accessories
 Terminal Block for Power input x2
 Hardcopy of EH series Quick Installing Guide x 1
- Optional Accessories
 AD15-24C (US) AC100V~240V/DC24V, US Plug (optional)
 AD15-24D (EU) AC100V~240V/DC24V, EU Plug (optional)
3. Product outline
EH2006
The EH2006 supports six 10/100
base-TX Fast Ethernet connections
with RJ-45 connectors
EH2005-Fs
The EH2005-Fs supports four
10/100 base-TX Fast Ethernet with
RJ45 connectors and one
100Base-FX single-mode Fiber
connection with SC connector
EH2005-Fm
The EH2005-Fm supports four
10/100 base-TX Fast Ethernet with
RJ-45 connectors and one
100Base-FX multi-mode Fiber
connection with ST connector

Quick Installing Guide Version 1.2
Atop ABLELink® Industrial Switch
EH2006/EH2005-Fs/EH2005-Fm
Copyright © 2006 ATOP Technologies, Inc.
All rights reserved
- 2 -
4. Hardware Installation
Step1: Connect to Power
 Prepare suitable DC 9~30V power source and connected to EH switch by 3-pin
Terminal blocks.
 You can connected two DC input for power auto-backup need.
 Check P1/P2 LED for correct power source, everything is OK if the LES(s) was
lighted
Step2: Connect to Network Device by Ethernet
 Connected your device by standard UTP/STP cable with RJ-45 connectors to EH
switch.
 The LINK LED will be lighted if the Ethernet connection was linked.
 It is indicated and blinked if data was transfer by EH switch hub.
UL Notice for Power supplier
All the series of EH products are intended to be supplied by a Listed Power Unit
marked with “LPS”, “Limited Power Source” or “Class 2” and output rate 9~30VDC,
0.3A minimum. Or, use the recommended power supply in “Optional Accessories.
5. LED Indicators
There are four LED indicators located at the front panel of EH series.
Name LED Status Description
Off Everything is OK
ALM RED
On Something is wrong. It will be lighted, if the any power
input was fail, or the network port was broken.
Off Power input 1/2 is not plugged yet
P1/P2 Green
On Power status is Ready
Off Link is Boren or Cable not be plugged
Green Blink Traffic be indicted for data transfer
Off 10M rate be active
RJ45 Yellow On 100M rate be active
Off No data be transmitted
Data Blink Working when data transmitted
Off No media be available
Fiber
SC/ST Link On Working when media was ready
7. Configuration and Setting Methods
Any settings or configuration are unnecessary.

Quick Installing Guide Version 1.2
Atop ABLELink® Industrial Switch
EH2006/EH2005-Fs/EH2005-Fm
Copyright © 2006 ATOP Technologies, Inc.
All rights reserved
- 3 -
8. Pin assignment of Network Connections
10/100BaseT(X) Ethernet Port Connection
RJ-45
Pin 1 2 3 4 5 6 7 8
Signal Tx+ Tx- Rx+
Rx-
100BaseFx Fiber Cable Wring
-SC/ST Connectors
SC Connectors ST Connecters
Fiber port
Single-Mode Multi-mode
-Cable Wiring
TX A  BRX
ST Connector RX B 
A
TX
TX A  BRX
SC Connector RX B 
A
TX
Terminal Block for Power input
FGVin-Vin+
Pin Vin+ Vin- FG
Signal DC9~30V 0V Frame Ground
9. ATOP Customer Services and Supports
1. Please contact your local dealers or Atop Technical Support Center at the following
numbers.
 [phone] (Atop Taiwan)
 [phone] (Atop China)
2. Please report the defected problems via Atop’s Web site or E-mail account
Web Site:www.atop.com.tw, e-mail: [email protected]
Web Site:www.atop.com.cn, e-mail: [email protected]