Atop RHG7528 Series Manual

Industrial Managed Rack-Mount Modular
Gigabit Ethernet Switch
RHG7528 / RHG7628 Series
Version 1.0
Updated in April, 2017
P/N:89900501G
Inside the package you will find the following items:
■ Industrial Managed Rack-Mount Modular Gigabit Ethernet Switch x 1
■ Rack Mount Kit x 2
■ 4-pin Terminal block x 1 for the relay output
■ 3-pin Terminal block x 2 for the DC models power input
■ Protective caps for all SFP ports (Depend on purchased model)
■ Installation Guide with Warranty Card x 1
Front View
Back View
Never install or work on electrical or cabling during periods of lightning activity.
Never connect or disconnect power when hazardous gases are present.
Warning:Hot Surface Do Not Touch.
Caution: CLASS 1 LASER PRODUCT. Do not stare into the laser!
IndoorIndoor
This equipment should be installed indoor and not connect directly with equipment
installed outdoor.
Throw the device must follow RoHS procedure to recycle
DC for power up
CPU board only
AC single for power up
CPU board only
AC redundant for power up
CPU board only
Dual AC / Dual DC models
Single AC mode
M1M4M3M21
10G
2
34 Console Reset
Run
Ring
R.M.
ALM
P1
PWR
PoE
P2
P1
P2
1
1
2
3
4
5
6
7
8
PoEPoE
234
5 6 7 8
1 2 34
56 7 8
123 4
5678
M1M4M3M21
10G
2
34 Console Reset
Run
Ring
R.M.
ALM
P1
PWR
PoE
P1
P2
1
1
2
3
4
5
6
7
8
PoEPoE
234
5 6 7 8
1 2 34
56 7 8
123 4
5678
PWR2 PWR1
Relay2 Relay1
123 41 2 3 4
++_ _ + + _ _
PoE PWR2(Max Input 360W) PoE PWR1(Max Input 360W)
PWR1
Relay2 Relay1
123 41 2 3 4
++_ _ + + _ _
PoE PWR2(Max Input 360W) PoE PWR1(Max Input 360W)
Relay2 Relay1
123
123
F.G.-
+
123
F.G.-
+
41 2 3 4
++_ _ + + _ _
PoE PWR2(Max Input 360W) PoE PWR1(Max Input 360W)
You can then choose whether to plug in the I/O ports at this point or do it later.
Next you can then proceed to connect the device to the LAN (switch or PC),
take care on using the RJ-45 connector; after this we can then proceed to the
device’s settings.
3.
The openings to the sides are for the devices heat dissipation. Please never
obstruct or cover them with any objects.
4.
This switch’s factory IP by default is 10.0.50.1 . you can access the device by
its Web UI once it is connected to a physical network (or using Management
Utility, for more information on Management Utility, please refer to its manual).
Please be aware that the PC needed for this procedure needs to be in the
same subnet, or you may refer yourself to the device User’s Manual.
5.
Ground the device properly. You can use the FG pin in the terminal block. It is
required to connect to the grounds at all times to ensure overall maximum
performance.
1.
2. If you opt to place the device on a rack, you will need to secure the rack
mounts kit on to the device before placing it on the rack. If you opt to place the
device on a surface, you can put on the foot rubbers to prevent the device from
sliding.
1 2 3 4
+ + __
1 2 3 4
+ + - -
PoE PWR
■ Power input : 110-220 VAC, 0.58 A Max, 64W Max (For AC version models)
48-57 VDC, 0.68A Max, 32.7W Max (For DC version models)
45-57 VDC, 8.4A Max, 370W Max (For 802.3af models)
51-57 VDC, 14.4A Max, 720W Max (For 802.3at models)
■ Alarm output : 1A@24A VDC for signal use only
1 2 3
F.G. - +
DC PWR
+_F.G.
32 1
Relay output
Relay2 Relay1

LED
Color
State
Description
PWR1/
PWR2
Green
On
Power is supplied from PWR1/PWR2
Off
No power input detected from PWR1/PWR2
ALM Red
On
Alarm is triggered by user defined events
Off
Alarm is not triggered by user defined events
RUN Green
Blinking
AP firmware is running normally
Off
System is not ready or halt
Ring Green
On
All rings in normal condition or CChain in
normal condition
Blinking
Ring in protection state or a port is link down
in CChain
Off
Ring is disabled or CChain is disable
R.M Green
On
The device is a Master of the ERPS Ring or
iA-Ring or a Head of CChain
Blinking
The device is a Tail of CChain
Off
The device is a Slave of the ERPS Ring or
iA-Ring or a Member of CChain
10G
On LED
Panel
Green
On Port is linked
Blinking
Data is transmitting on this port
Off
No data is transmitting
LAN
Amber
On
Ethernet is linked at 1000Mbps
Blinking
Ethernet is linked at 100Mbps
Off
Ethernet is linked at 10Mbps
Green
On
Ethernet is linked
Blinking Ethernet is active and data is being transmitted
Off
Ethernet is not linked
SFP
(1G)
Amber
On
Ethernet is linked at 1000Mbps
Blinking
Ethernet is linked at 100Mbps
Off
Ethernet is linked at 10Mbps
Green
On
Ethernet is linked
Blinking Ethernet is active and data is being transmitted
Off Ethernet is not linked
SFP
PoE
MACsec
(10G)
Amber
OnEthernet is linked at 10GMbps
Blinking Ethernet is linked at 1000Mbps
Off Ethernet is linked at 100Mbps
Green
OnEthernet is linked
Blinking Ethernet is active and data is being transmitted
Off Ethernet is not linked
Amber
OnPower is being supplied to a Powered
Device (PD)
Off Power is not supplied to a Powered Device(PD)
Blue
OnMACsec active on that port
Blinking Ethernet is active and data is being transmitted
Off Ethernet is not linked
If the device requires servicing of any kind, you may need to disconnect and
remove it from its mounting. The initial installation should be done in a way that
makes this as convenient as possible.
■ Voltage/Power lines should be properly insulated as well as other cables. Be
careful when handing the so as to not trip over
■ Do not under any circumstance insert foreign objects of any kind into the heat
dissipation holes located in the different faces of the device. This may not only
harm the internal layout but might cause harm to you as well.
■ Do not under any circumstance open the device for any reason. Please
contact your dealer for any repair needed or follow the instructions on section
of your User’s Manual.
Field Maintenance and Service
Attention
1. It is recommend to use at least a 20 AWG cable for the AC power input.
It is suggested the cable to be resistant to at least 85°C temperature on the
power connector.
2. If the equipment is used in a manner not specified by the manufacturer, the
protection provided by the equipment may not be impaired.
3. Clean the device with dry or humid (water) soft cloth.
4. Before powering on the device, the Functional Ground (Grounding Screw)
shall be connected to the ground.
5. If the device is AC please connect PWR1. If AC redundant, connect PWR1
and PWR2 to the 100~240V AC power source. This power input manages
the full device functions except from PoE.
6. If the device is DC powered, please connect DC1 and DC2 to the DC
power supply.
7. If PoE is going to be used, also POE PWR1 and POE PWR2 should be
connected to 48~57 VDC power supplies). In order to avoid overheat and
damages to the internal components the user should follow the below
guidelines:
■ Total PoE power needed is <= 360W: connect to either power supply
■ POE PWR1 or POE PWR2 or both.
■ Total PoE power needed is >360W but <=720W (max): connect to both
■ POE PWR1 and POE PWR2 in order to avoid overhead.
8. POE PWR1 or POE PWR2 support maximum input 360 W.
9. POE PWR1 / POE PWR2 , + / - pins should be connected in same PWR input
Terminal block, please don’t cross-connect.
Environmental Limits
■ Operating Tem perature: -40 to 75°C (-40 to 167°F)
■ Storage Temperature: -40 to 85°C (-40 to 185°F)
■ Ambient Relative Humidity: 5 to 95%, 55°C (non-condensing)
■ Altitude: up to 2,000 m
■ Housing Protection : IP 30
Front View
Back View
Top View
Site View
482,6
6
464,5
31,8
440
340
44
Customers shall always obtain an authorized "RMA" number from Atop before
shipping the goods to be repaired to Atop. When in normal use, a sold product
shall be replaced with a new one within 3 months after purchase. The shipping
cost from the customer to Atop will be reimbursed by Atop.
After 3 months and still within the warranty period, it is up to Atop whether to
replace the unit with a new one; normally, as long as a product is under warranty,
all parts and labor are free of charge to the customers.
After the warranty period, the customer shall cover the cost for parts and
labor.Three months after purchase, the shipping cost from the customer to Atop
will not be reimbursed, but the shipping cost from Atop to the customer will be
paid by Atop.
Atop shall not be held responsible for any consequential losses from using Atop’s
product.
Warranty Policy
The warranty certification will not be effective until an authorized stamp issued by
Atop’s overseas agents.
Purchase Date: / / (yyyy/mm/dd)
Serial Number
Product CategoriesWarranty WarrantyProduct Categories
Media Converters
Embedded Device Servers
Ethernet Switches
Wireless
Serial Device Servers
Modbus Gateways
DIN-Rail Power Supplies
Power Adaptors
Antennas
Other Accessories
Warranty Conditions
RMA and Shipping Costs Reimbursement
Limited Liability
1. Please contact your local dealers or Atop Technical Support Center at the
following numbers.
+ 886-3-550-8137 (Atop Taiwan)
+ 86-21-6495-6232 (Atop China)
2. Please report the defected problems via Atop’s Web site or E-mail account
Web Site：www.atop.com.tw, e-mail：[email protected]
Web Site：www.atop.com.cn, e-mail：[email protected]
3. Company Addr: 2F, No. 146, Sec. 1, Tung-Hsing Rd., Jubei, Hsinchu 30261,
Taiwan, R.O.C.
Manufacturer Addr: 1st FL 30 R&D RD II,SCIENCE-BASED INDUSTRIAL
PARK,HSINCHU 300 TAIWAN, R.O.C
Atop Customer Services and Supports
Products supplied by Atop Technologies are covered in this warranty for
sub-standard performance or defective workmanship. The warranty is not,
however, extended to goods damaged in the following circumstances:
(a) Excessive forces or impacts
(b) War or an Act of God: wind storm, fire, flood, electric shock, earthquake
(c) Use of unqualified power supply, connectors, or unauthorized parts/kits
(d) Replacement with unauthorized parts
Warranty Period
─ Any changes to this material will be announced on Atop website. ─